提交 801173fe 编写于 作者: J Jagan Teki 提交者: Shawn Guo

ARM: dts: imx6qdl-icore: Add FEC support

Add FEC support for Engicam i.CoreM6 dql modules.

Observed similar 'eth0: link is not ready' issue which was
discussed in [1] due rmii mode with external ref_clk, so added
clock node along with the properties mentioned by Shawn in [2]

FEC link log:
------------
$ ifconfig eth0 up
[   27.905187] SMSC LAN8710/LAN8720 2188000.ethernet:00: attached PHY driver
               [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=2188000.ethernet:00, irq=-1)
[   27.918982] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready

[1] https://patchwork.kernel.org/patch/3491061/
[2] https://patchwork.kernel.org/patch/3490511/

Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>
上级 9daee307
......@@ -74,6 +74,12 @@
regulator-boot-on;
regulator-always-on;
};
rmii_clk: clock-rmii-clk {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <25000000>; /* 25MHz for example */
};
};
&can1 {
......@@ -93,6 +99,15 @@
assigned-clock-parents = <&clks IMX6QDL_CLK_OSC>;
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
clocks = <&clks IMX6QDL_CLK_ENET>, <&clks IMX6QDL_CLK_ENET>, <&rmii_clk>;
phy-mode = "rmii";
status = "okay";
};
&gpmi {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpmi_nand>;
......@@ -150,6 +165,22 @@
};
&iomuxc {
pinctrl_enet: enetgrp {
fsl,pins = <
MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b1
MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
MX6QDL_PAD_ENET_REF_CLK__GPIO1_IO23 0x1b0b0
MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
>;
};
pinctrl_flexcan1: flexcan1grp {
fsl,pins = <
MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b020
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册