Audio-related clocks need to be represented in the device tree. Update
bindings to describe which clocks are needed, and DT files to include
those clocks.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Audio-related clocks need to be represented in the device tree. Update
bindings to describe which clocks are needed, and DT files to include
those clocks.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

NVIDIA's Tegra114 reference platform Dalmore has voltage switch
regulators which are controlled by the Tegra GPIOs.

Add DT node for fixed regulators.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

NVIDIA's Tegra114 reference platform, Dalmore, uses the TPS65090 as
secondary PMICs which is mainly act as voltage switch regulator
controlled by i2c communication.

Add DT node for TPS65090.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
[swarren: remove unit-address from node name since it's unique already]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Dalmore uses the TPS51632 as CPU regulator. The device is connected
on I2C5.

Add DT node for TPS51632.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This patch adds the node for the bq20z45 I2C gas gauge which is
compatible with the sbs-battery power supply driver.
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
[swarren: remove unit-address from node name since it's unique already]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

NVIDIA's Tegra114 has 6 SPI controllers. These controllers are
redesign on T114 with different register interface.

Add DT entry for spi controllers and make it compatible with
"nvidia,tegra114-spi", since they are a new incompatible design.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed reg property for 3rd SPI controller]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

NVIDIA's Tegra114 SoCs have the matrix keyboard controller which
supports 11x8 type of matrix. The number of rows and columns
are configurable.

Add DT entry for KBC controller with compatibility as "nvidia,tegra114-kbc".
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Add APB DMA requestor and serial aliases for serial controller.
There are two serial drivers i.e. 8250 based simple serial driver
and APB DMA based serial driver for higher baudrate and performace.

The simple serial driver is selected by compatible value
"nvidia,tegra114-uart", "nvidia,tegra20-uart", and the APB DMA based
driver is selected by compatible value "nvidia,tegra114-hsuart",
"nvidia,tegra30-hsuart".
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

NVIDIA's Tegra114 has 5 I2C controllers. These controllers have the
following changes which makes incompatible with previous hardware:
- Single clock source to I2C controller.
- Interrupt support for per packet transfer.

Add DT entry for I2C controllers and make it compatible with
"nvidia,tegra114-i2c".
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed location of status property for consistency]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

NVIDIA's Tegra114 has 32 channels APB DMA controller. Add DT entry for
APB DMA controllers and make it compatible with "nvidia,tegra114-apbdma".

Tegra114 DMA controller is not compatible with Tegra30/Tegra20 DMA
controller driver as in Tegra114, the global pause also clock gate the
DMA register and hence it iw not possible to write the DMA register
with global pause.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed DT node order]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This patch adds a device tree node for the four PWM controllers present
on Tegra114.
Signed-off-by: NAndrew Chew <achew@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

We should be defining the PWM nodes with status as "disabled" in the
chip-specific dtsi file, since we don't know whether specific boards
will use the PWM or not. This patch fixes the PWM node status for
Tegra20 and Tegra30.

Also fixed the one user of PWM, which is the Tegra20 medcom-wide board,
so that PWM is set to "okay" in the board-specific dts file.
Signed-off-by: NAndrew Chew <achew@nvidia.com>
[swarren: in medcom-wide: fixed node sort order, removed duplicate pwm:
label, fixed syntax error]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Dalmore has a built-in eMMC device and a user-accessible SD card slot.
Add device tree nodes to enable these.

Based on changes by: Pritesh Raithatha <praithatha@nvidia.com>
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
[swarren: added commit description, fixed DT node sort order]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This patch adds in the SDHCI nodes for the busses supported on Tegra114
boards.
Signed-off-by: NPritesh Raithatha <praithatha@nvidia.com>
[Rhyland added clk refs to & reordered sdhci nodes and removed spaces]
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
[swarren: fixed DT node sort order]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This change adds the default pinctrl nodes for the Dalmore Tegra114
platform.
Signed-off-by: NPritesh Raithatha <praithatha@nvidia.com>
[Rhyland added patch description]
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
[swarren: fixed DT node sort order]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The USB PHY nodes are all grouped together rather than being sorted based
on reg address like all other nodes fix this.

I apologize for the churn; I should have noticed this during review of the
patches that caused this.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Remove white-space from empty line; triggers checkpatch.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Add references to tegra_car clocks for the basic device nodes. Also remove
the clock-frequency property of the serial node as the UART driver can now
use the clock framework to obtain the frequency.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Adding the bindings of the clock source of PMC in DT.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

There was only chip enable and readdy/busy pins for the nand controller.
This add the rest of the pins.
pinctrl_nand_16bits contains the specific muxes for 16 bits NANDs.
Signed-off-by: NRichard Genoud <richard.genoud@gmail.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Comments on NAND pins where inverted.
Signed-off-by: NRichard Genoud <richard.genoud@gmail.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The ab8500 device is a child of the prcmu device, which is a memory mapped
bus device, whose children are addressable using physical memory addresses,
not using mailboxes, so a mailbox number in the ab8500 node cannot be
parsed by DT. Nothing uses this number, since it was only introduced
as part of the failed attempt to clean up prcmu mailbox handling, and
we can simply remove it.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch adds #dma-cells property to PL330 DMA controller nodes for
supporting generic dma dt bindings on SOCFPGA platform. #dma-channels
and #dma-requests are not required now but added in advance.
Signed-off-by: NPadmavathi Venna <padma.v@samsung.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The PMC HW is not 100% compatible across all Tegra series. We need to
specify them in DT.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The new clockframework introduced DT IDs for each clock. To be able to remove
the device registrations, this driver needs to be updated to use the DT IDs.
Note that the actual removal of the clk_register_clkdev() calls will be done
in a later series.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The GPIO pin of SD slot card detection should active low.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Tested-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The orion5x-lacie-ethernet-disk-mini-v2.dts file was using
"marvell-orion5x-88f5182" as a compatible string, while it should have
been "marvell,orion5x-88f5182".
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

There is no need to have a #address-cells property in the MPIC Device
Tree node, and more than that, having it confuses the of_irq_map_raw()
logic, which will be used by the Marvell PCIe driver.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Setting the reg-io-width to 1 byte represents more accurate
description of the HW.

This will fix an issue where UART driver causes kernel
panic during bootup. Gregory CLEMENT traced the issue to
autoconfig() in 8250.c, where the existence of FIFO is
checked from UART_IIR register. The register is now read as
32-bit value as the reg-io-width is set to 4-bytes. The
retuned value seems to contain bogus data for bits 31:8,
causing the issue.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The commit:

  48be9ac9 ARM: Dove: split legacy and DT setup

removed the RTC initialization.  This patch re-enables the RTC
via the DT.
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch modifies the Armada 370 Reference Design DTS file to enable
support for the two USB ports found on this board.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The Marvell RTC on Kirkwood makes use of the runit clock. Ensure the
driver clk_prepare_enable() this clock, otherwise there is a danger
the SoC will lockup when accessing RTC registers with the clock
disabled.
Reported-by: NSimon Baatz <gmbnomis@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The kirkwood SoC GPIO cores use the runit clock. Add code to
clk_prepare_enable() runit, otherwise there is a danger of locking up
the SoC by accessing the GPIO registers when runit clock is not
ticking.
Reported-by: NSimon Baatz <gmbnomis@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

When DT support for kirkwood was first introduced, there was no clock
infrastructure.  As a result, we had to manually pass the
clock-frequency to the driver from the device node.

Unfortunately, on kirkwood, with minimal config or all module configs,
clock-frequency breaks booting because of_serial doesn't consume the
gate_clk when clock-frequency is defined.

The end result on kirkwood is that runit gets gated, and then the boot
fails when the kernel tries to write to the serial port.

Fix the issue by removing the clock-frequency parameter from all
kirkwood dts files.

Booted on dreamplug without earlyprintk and successfully logged in via
ttyS0.
Reported-by: NSimon Baatz <gmbnomis@gmail.com>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch adds #dma-cells property to PL330 DMA controller
nodes for supporting generic dma dt bindings on samsung exynos
platforms. #dma-channels and #dma-requests are not required now
but added in advance.
Signed-off-by: NPadmavathi Venna <padma.v@samsung.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

As DT support for clocks and smp_twd is enabled, add clock entry
for smp_twd clock to DT.

This fixes the following error while booting the kernel:
smp_twd: clock not found -2
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
[swarren: include kernel log spew that this fixes]
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

BCM2835-ARM-Peripherals.pdf states that the I2C module's input clock is
nominally 150MHz, and that value is currently reflected in bcm2835.dtsi.
However, practical measurements show that the rate is actually 250MHz,
and this agrees with various downstream kernels.

Switch the I2C clock's frequency to 250MHz so that the generated bus
clock rate is accurate.
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

According to fsl,imx53-pinctrl.txt, the pin number of DISP1_DAT_21
should be 545, while 543 is IPU_CSI0_D_3.  Along with the change,
one duplication of DISP1_DAT_0 in disp1-grp1 is removed.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The Armada 370 Reference Design board has one SD card slot, directly
connected to the SDIO IP of the SoC, so we enable this IP. there are no
GPIOs for card-detect and write-protect so we do not specify any.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>