To detect cases if the firmare or board file is corrupted or otherwise modified print crc32 value
of both. Now the output looks like:

ath10k_pci 0000:02:00.0: pci irq msi interrupts 1 irq_mode 0 reset_mode 0
ath10k_pci 0000:02:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002
ath10k_pci 0000:02:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 1
ath10k_pci 0000:02:00.0: firmware ver 10.4.1.00030-1 api 5 features no-p2p crc32 d2901e01
ath10k_pci 0000:02:00.0: board_file api 1 bmi_id 1:1 crc32 7e56fd07
ath10k_pci 0000:02:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Earlier we printed all the info messages after a successful device
initialisation and firmware boot, but that's problematic if something goes
wrong and there's no easy way to know what firmware version was used and so on.

Split the info messages into smaller pieces and print them as soon as we have
the info available.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

That way we can split the messages to be printed in different stages of
device initialisation.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is to make it easier to split them later and also make room for crc32
checksums.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

We check board id from all board types, not just qca99x0, so the error message
was misleading.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

QCA988X firmware starting from 10.2.4.70.12-2 has capability to support
Mesh Control Field Present bit in QoS field in native Wi-Fi mode.
Hence apply Mesh subtype according to the WMI service map.

Firmware will allows unicast, broadcast, multicast, and WDS frame
(FromDS = 1 and ToDS = 1) to be received via the interface, once Mesh
subtype is used.

The firmware and this patch together make native Wi-Fi mode comply to
IEEE802.11s Mesh frame in open mode, but the firmware doesn't yet
support secured Mesh mode.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

QCA988X firmware starting from 10.2.4.70.12-2 supports new
vdev subtypes for proxy STA and Mesh, hence add them to be used
as needed.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Update WMI 10.x service map to sync with firmware 10.2.4.70.12-2
released on 11/11/2015 which is the latest QCA988X firmware as of
11/18/2015.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix write permission for few of the debugfs entries
which support write file operations as well.
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Allocations from the DMA zone were originally added for legacy ISA
stuff, or PCI devices that have specific limitations in their DMA
addressing capabilities. It has no place in ath10k, which can do
full 32-bit DMA.

Fixes memory allocation errors on some platforms.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Enable AP + STA interface combination support for 10.x and
this enables Repeater mode testing (with WDS Repeater combinations
as well). Fix indentation as well.

Based on the suggestions from Michal and Yanbo Li,
thanks to them
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The error message order of board data fetch is board info,
directory, and then file name, hence place print arguments
in the order.

Fixes: 0a51b343 ("ath10k: add board 2 API support")
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Txbuf is no longer a DMA pool and can be easily
tracked with a mere msdu_id. This saves 10 bytes
on 64bit systems and 6 bytes on 32bit systems of
precious sk_buff control buffer.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This prepares the driver for future ieee80211_txq
and wake_tx_queue() support.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Frames are not guaranteed to be 802.11 frames in
ath10k_htt_tx() and the tx completion handler.
In some cases, like TDLS, they can be Ethernet.
Hence checking, e.g. frame_control could yield
bogus results and behavior.

Fortunately this wasn't a real problem so far
because there's no FW/HW combination to encounter
this problem.

However it is good to fix this in advance.

Fixes: 75d85fd9 ("ath10k: introduce basic tdls functionality")
Fixes: eebc67fe ("ath10k: fix pmf for wmi-tlv on qca6174")
Fixes: 7b7da0a0 ("ath10k: drop probe responses when too many are queued")
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It was wasteful to have all the flags as separate
bools.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It was wasteful to keep it in the struct.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It was wasteful to keep it in the struct.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It was wasteful to keep it in the struct because
it can be passed as function argument down the tx
path.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

All functions should have ath10k_{filename}_
prefixes.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It was wasteful to have two flags describing
the same thing.

While at it fix code style of
ath10k_tx_h_use_hwcrypto().
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The QCA99X0 4 addresses RX packets pad 2 bytes at the beginning of
MSDU instead the end of ieee80211 header to keep alignment. The currently RX
data path can't parse the header correctly in this case. This patch fixes it
for QCA99X0.
Signed-off-by: NYanbo Li <yanbol@qca.qualcomm.com>
[kvalo@qca.qualcomm.com: checkpatch fixes and naming changes]
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To prevent race when connect flow may run in parallel with
the disconnect event.

Scenario leading to the bug is: while running connect flow on the AP,
STA sends disconnect. log follows.

<7>[  668.736269] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Configure for connection CID 1
<7>[  668.736269] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil_vring_init_tx() max_mpdu_size 2048
<7>[  668.736301] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil_vring_alloc()
<7>[  668.736363] wil6210 0000:01:00.0: wlan0: DBG[MISC]vring[1024] 0xffbe8000:d962ce08 0xdb244000
<7>[  668.736394] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Head 0x00880300 -> 0x00880308
<7>[  668.736394] wil6210 0000:01:00.0: wlan0: DBG[ WMI]WMI command 0x0821 [28]
<7>[  668.736426] DBG[ WMI]Cmd 00000000: 20 00 24 00 00 00 00 00 00 00 21 08 00 00 00 00   .$.......!.....
<7>[  668.736426] DBG[ WMI]cmd 00000000: 00 00 00 00 00 00 5f 5c 00 00 00 00 00 04 00 08  ......_\........
<7>[  668.736457] DBG[ WMI]cmd 00000010: 01 01 00 00 00 00 00 00 00 00 ff 0f              ............
<7>[  668.736488] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]Pseudo IRQ 0x00000004
<7>[  668.736519] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Handle WMI 0x1824 (reply_id 0x1821)
<7>[  668.736519] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]wil6210_mask_irq_pseudo()
<7>[  668.736519] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]ISR MISC 0x20000000
<7>[  668.736551] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Handle WMI 0x1003 (reply_id 0x1821)
<7>[  668.736551] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Disconnect 04:ce:14:00:07:70 reason [proto 3 wmi 4]
<7>[  668.736582] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil6210_disconnect()
<7>[  668.736613] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]Thread IRQ
<7>[  668.736613] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]Thread ISR MISC 0x20000000
<7>[  668.736644] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]MBOX event
<7>[  668.736644] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Mbox head 00880330 tail 00880328
<7>[  668.736676] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Mbox evt 001a 0010 0000 00
<7>[  668.736676] wil6210 0000:01:00.0: wlan0: DBG[ WMI]WMI event 0x1821 MID 0 @3255145 msec
<7>[  668.736707] DBG[ WMI]evt 00000000: 1a 00 10 00 00 00 00 10 00 00 21 18 69 ab 31 00  ..........!.i.1.
<7>[  668.736707] DBG[ WMI]evt 00000010: 01 01 00 00 00 00 00 00                          ........
<7>[  668.736738] wil6210 0000:01:00.0: wlan0: DBG[ WMI]queue_work -> 0
<7>[  668.736738] wil6210 0000:01:00.0: wlan0: DBG[ WMI]wmi_recv_cmd -> 1 events queued
<7>[  668.736769] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]wil6210_unmask_irq_pseudo()
<7>[  668.736832] wil6210 0000:01:00.0: wlan0: DBG[MISC]Disconnect 04:ce:14:00:07:70, CID=1, reason=3
<7>[  668.736832] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil_disconnect_cid(CID 1, status 1)
<7>[  668.736894] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil_vring_fini_tx() id=1
<7>[  668.736894] wil6210 0000:01:00.0: wlan0: DBG[MISC]free Tx vring 1 [1024] 0xffbe8000:d962ce08 0xdb244000
<7>[  668.736957] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Handle WMI 0x1821 (reply_id 0x1821)
<7>[  668.736988] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Complete WMI 0x1821
<7>[  668.737019] wil6210 0000:01:00.0: wlan0: DBG[ WMI]wmi_call(0x0821->0x1821) completed in 0 msec
<3>[  668.737019] wil6210 0000:01:00.0: wlan0: Tx config failed, status 0x01
<7>[  668.739518] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil_cfg80211_del_station(04:ce:14:00:07:70, reason=2)
<7>[  668.739550] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil6210_disconnect()
<7>[  668.739550] wil6210 0000:01:00.0: wlan0: DBG[MISC]_wil6210_disconnect(bssid=04:ce:14:00:07:70, reason=2, ev-)
<7>[  668.739581] wil6210 0000:01:00.0: wlan0: DBG[MISC]Disconnect 04:ce:14:00:07:70, CID=-2, reason=2
<7>[  668.742705] wil6210 0000:01:00.0: wlan0: DBG[MISC]free Tx vring 1 [1024] 0x  (null):d962ce08 0x  (null)
<3>[  668.742736] __dma_free_remap: trying to free invalid coherent area:   (null)
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The RX rate idx is not correct for 11G mode OFDM packet.
Because the bitrate table start with CCK index instead of OFDM.
Signed-off-by: NYanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Of a word in struct htt_data_tx_desc htt version >= 3.4 firmware uses
LSB 16-bit for frequency configuration which is used for offchannel tx
and MSB 16-bit is for peerid. But other firmwares using version 2.X
(10.1, 10.2.2, 10.2.4 and 10.4) are using 32-bit for peerid in htt tx
desc. So far no issue is found with the existing code setting peerid and
freq for HTT version 2.X, this could be mainly because of 0 as frequecy
(home channel) is being always passed with those firmwares. There may be
issues when non-zero freq is passed with firmware using < 3.4 htt version.
To be safe use target_version_major and target_version_minor along with
htt-op-version before configuring peer id and freq in htt tx desc. This
patch extends ath10k_mac_tx_frm_has_freq() to check for htt_op_version_tlv
and uses the helper while setting peerid in htt_tx_desc.

Fixes: 8d6d3624 ("ath10k: fix offchan reliability")
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Rename ath10k_mac_need_offchan_tx_work() to ath10k_mac_tx_frm_has_freq()
to make it more meaningful. This helper will be used in the future
change. No functionality change.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There is an extra 4-byte member when compared to WMI 10.2 added to
assoc complete command in WMI 10.4. This new member is used for 160Mhz
related configuration. This WMI command mismatch between host and
firmware does not cause any real issues because this new member is not
used in 10.4 firmwares so far (10.4.1.00030-1). This difference in WMI
command interface brings in a new wmi_ops for 10.4 gen_peer_assoc().
No noticeable functionality differences with this change can be seen
with the current 10.4 firmwares, but the WMI interface has to be
fixed to work with future 10.4 firmwares which may be using this new
member.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

As not all QCA98XX radios are not connected to Bluetooth modules, enabling the
BT coex feature in firmware will have side effects if the radio's GPIO are
connected with other (non-BT) HW modules. Add debugfs file to control the
firmware BT coex logic and set the feature as disable by default to avoid that
btcoex is accidentally enabled.

To enable this feature, execute:

echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/btcoex

To disable:

echo 0 > /sys/kernel/debug/ieee80211/phyX/ath10k/btcoex

The firmware support this feature since 10.2.4.54 on 2G-only board, dual band
or 5G boards don't support this. The feature's name is WMI_SERVICE_COEX_GPIO
and the btcoex file is not created if firmware doesn't support it.
Signed-off-by: NYanbo Li <yanbol@qca.qualcomm.com>
[kvalo@qca.qualcomm.com: use btcoex filename and other smaller fixes]
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch adds pktlog support for 10.4 fw versions.
Signed-off-by: NVivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

No functionality change, just sync to the latest
pdev params that 10.4 firmware defines.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

No real functionality change, add WMI command/event
defines to be in sync with 10.4 firmware.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

No functional changes, adds new wmi service bits for
10.4 firmware to be sync with 10.4 firmware.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch enables thermal throttling support for 10.4 firmware.
Signed-off-by: NTamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Set peer's management frame protection flag in peer assoc command,
this setting will enable/disable encrytion of management frames in fw.

Setting of this flag is based on whether MFP is enabled/disabled at STA
and a firmware feature flag ATH10K_FW_FEATURE_MFP_SUPPORT. This is because
only firmwares 10.1.561 and above have support for MFP.
Signed-off-by: NTamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: NManikanta pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Abstraction layer for peer flags is added to fix ABI breakage.
Signed-off-by: NTamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: NSenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch replaces multiple if conditional checks with a single if condition
in WMI management rx handler. Found during code review.
Signed-off-by: NManikanta Pubbisetty <manikanta.pubbisetty@gmail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This supports a way to get target stats through normal
ethtool stats API.

For instance:
# ethtool -S wlan1
NIC statistics:
     tx_pkts_nic: 353
     tx_bytes_nic: 25142
     rx_pkts_nic: 6
     rx_bytes_nic: 996
     d_tx_ucast_pkts: 89
     d_tx_bcast_pkts: 264
     d_tx_ucast_bytes: 3020
     d_tx_bcast_bytes: 22122
...
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This will allow us to call it from elsewhere when implementing
ethtool stats.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Improper use of strlcpy caused garbage to be appended to the
firmware version string.  Fix this by paying attention to the
ie_lenth.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It can take a user a while to understand why their
NIC that advertises 802.11n support cannot actually
do 802.11n.  Print out a warning in the logs to save
the next poor person to use this NIC some trouble.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>