When a powered on dual-mode controller has been configured to operate
as LE only with secure connections, then the BR/EDR side of things can
not be switched back on. Do reconfigure the controller it first needs
to be powered down.

The secure connections feature is implemented in the BR/EDR controller
while for LE it is implemented in the host. So explicitly forbid such
a transaction to avoid inconsistent states.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The BR/EDR Secure Connections feature should only be enabled when the
Secure Simple Pairing mode has been enabled first. However since secure
connections is feature that is valid for BR/EDR and LE, this needs
special handling.

When enabling secure connections on a LE only configured controller,
thent the BR/EDR side should not be enabled in the controller. This
patches makes the BR/EDR Secure Connections feature depending on
enabling Secure Simple Pairing mode first.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Start Discovery was reporting 0 RSSI for invalid RSSI only for
BR/EDR devices. LE devices were reported with RSSI 127.
Signed-off-by: NSzymon Janc <szymon.janc@tieto.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.19+

When the controller gets powered on via the management interface, then
register the supported SMP channels. There is no point in registering
these channels earlier since it is not know what identity address the
controller is going to operate with.

When powering down a controller unregister all SMP channels. This is
required since a powered down controller is allowed to change its
identity address.

In addition the SMP channels are only available when the controller
is powered via the management interface. When using legacy ioctl, then
Bluetooth Low Energy is not supported and registering kernel side SMP
integration may actually cause confusion.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

For dual-mode controllers it is possible to disable BR/EDR and operate
as LE single mode controllers with a static random address. If that is
the case, then refuse switching BR/EDR back on after the controller has
been powered.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When hci_req_run() calls its provided complete function and one of the
HCI commands in the sequence fails, then provide the opcode of failing
command. In case of success HCI_OP_NOP is provided since all commands
completed.

This patch fixes the prototype of hci_req_complete_t and all its users.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The force_sc_support debugfs option was introduced to easily work with
pre-production Bluetooth 4.1 silicon. This option is no longer needed
since controllers supporting BR/EDR Secure Connections feature are now
available.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The cmd_complete callbacks for pending mgmt commands may fail e.g. in
the case of memory allocation. Previously this error would be caught and
returned to user space in the form of a failed write on the mgmt socket
(when the error happened in the mgmt command handler) but with the
introduction of the generic cmd_complete callback this information was
lost. This patch returns the feature by making cmd_complete callbacks
return int instead of void.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch updates the Add Device mgmt command handler to use a
hci_request to wait for HCI command completion before notifying user
space of the mgmt command completion. To do this we need to add an extra
hci_request parameter to the hci_conn_params_set function. Since this
function has no other users besides mgmt.c it's moved there as a static
function.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch updates the Remove Device mgmt command handler to use a
hci_request to wait for HCI command completion before notifying user
space of the mgmt command completion. This way we ensure that once the
mgmt command returns all HCI commands triggered by it have also
completed.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Many places using hci_update_background_scan() try to synchronize
whatever they're doing with the help of hci_request callbacks. However,
since the hci_update_background_scan() function hasn't so far accepted a
hci_request pointer any commands triggered by it have been left out by
the synchronization. This patch modifies the API in a similar way as was
done for hci_update_page_scan, i.e. there's a variant that takes a
hci_request and another one that takes a hci_dev.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

None of the hci_request related things in net/bluetooth/hci_core.h are
needed anywhere outside of the core bluetooth module. This patch creates
a new net/bluetooth/hci_request.c file with its corresponding h-file and
moves the functionality there from hci_core.c and hci_core.h.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

To keep the parameter list and its semantics clear it makes sense to
split the hci_update_page_scan function into two separate functions: one
taking a hci_dev and another taking a hci_request. The one taking a
hci_dev constructs its own hci_request and then calls the other
function.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The optimization for filtering out extended inquiry results, advertising
reports or scan response data based on provided UUID list has a logic
bug. In case no match is found in the advertising data, the scan
response is ignored and not checked against the filter. This will lead
to events being filtered wrongly.

Change the code to actually only drop the events when the scan response
data is not present. If it is present, it needs to be checked against
the provided filter.

The patch is a bit more complex than it needs to be. That is because
it also fixes this compiler warning that some gcc versions produce.

  CC      net/bluetooth/mgmt.o
net/bluetooth/mgmt.c: In function ‘mgmt_device_found’:
net/bluetooth/mgmt.c:7028:7: warning: ‘match’ may be used uninitialized in this function [-Wmaybe-uninitialized]
  bool match;
       ^

It seems that gcc can not clearly figure out the context of the match
variable. So just change the branches for the extended inquiry response
and advertising data around so that it is clear.
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When an adapter is removed (hci_unregister_dev) any pending mgmt
commands for that adapter should get the appropriate INVALID_INDEX
response. Since hci_unregister_dev() calls hci_dev_do_close() first
that'd so far have caused "not powered" responses to be sent.

Skipping the HCI_UNREGISTER case in mgmt_powered() is also not a
solution since before reaching the mgmt_index_removed() stage any
hci_conn callbacks (e.g. used by pairing) will get called, thereby
causing "disconnected" status responses to be sent.

The fix that covers all scenarios is to handle both INVALID_INDEX and
NOT_POWERED responses through the mgmt_powered() function. The
INVALID_INDEX response sending from mgmt_index_removed() is left
untouched since there are a couple of places not related to powering off
or removing an adapter that call it (e.g. configuring a new bdaddr).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If we're in the AUTO_OFF stage the powered_update_hci() function is
responsible for doing the updates to the HCI state that were not done
during the actual mgmt command handlers. One of the updates needing done
is for BR/EDR SC support. This patch adds the missing HCI command for SC
support to the powered_update_hci() function.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The pairing_complete() function is used as a pending mgmt command
cmd_complete callback. The expectation of such functions is that they
are not responsible themselves for calling mgmt_pending_remove(). This
patch fixes the incorrect mgmt_pending_remove() call in
pairing_complete() and adds it to the appropriate changes.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The pairing_complete() function relies on a hci_conn reference to be
able to access the hci_conn object. It should therefore only release
this reference once it's done accessing the object, i.e. at the end of
the function.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

mgmt_pending_remove() should be called with hci_dev_lock protection
and currently the rule to take dev lock is that all mgmt req_complete
functions should take dev lock. So this patch fixes the same in the
missing functions

Without this patch there is a chance of invalid memory access while
accessing the mgmt_pending list like below

bluetoothd:  392] [0] Backtrace:
bluetoothd:  392] [0] [<c04ec770>] (pending_eir_or_class+0x0/0x68) from [<c04f1830>] (add_uuid+0x34/0x1c4)
bluetoothd:  392] [0] [<c04f17fc>] (add_uuid+0x0/0x1c4) from [<c04f3cc4>] (mgmt_control+0x204/0x274)
bluetoothd:  392] [0] [<c04f3ac0>] (mgmt_control+0x0/0x274) from [<c04f609c>] (hci_sock_sendmsg+0x80/0x308)
bluetoothd:  392] [0] [<c04f601c>] (hci_sock_sendmsg+0x0/0x308) from [<c03d4d68>] (sock_aio_write+0x144/0x174)
bluetoothd:  392] [0]  r8:00000000 r7 7c1be90 r6 7c1be18 r5:00000017 r4 a90ea80
bluetoothd:  392] [0] [<c03d4c24>] (sock_aio_write+0x0/0x174) from [<c00e2d4c>] (do_sync_write+0xb0/0xe0)
bluetoothd:  392] [0] [<c00e2c9c>] (do_sync_write+0x0/0xe0) from [<c00e371c>] (vfs_write+0x134/0x13c)
bluetoothd:  392] [0]  r8:00000000 r7 7c1bf70 r6:beeca5c8 r5:00000017 r4 7c05900
bluetoothd:  392] [0] [<c00e35e8>] (vfs_write+0x0/0x13c) from [<c00e3910>] (sys_write+0x44/0x70)
bluetoothd:  392] [0]  r8:00000000 r7:00000004 r6:00000017 r5:beeca5c8 r4 7c05900
bluetoothd:  392] [0] [<c00e38cc>] (sys_write+0x0/0x70) from [<c000e3c0>] (ret_fast_syscall+0x0/0x30)
bluetoothd:  392] [0]  r9 7c1a000d r8:c000e568 r6:400b5f10 r5:403896d8 r4:beeca604
bluetoothd:  392] [0] Code: e28cc00c e152000c 0a00000f e3a00001 (e1d210b8)
bluetoothd:  392] [0] ---[ end trace 67b6ac67435864c4 ]---
bluetoothd:  392] [0] Kernel panic - not syncing: Fatal exception
Signed-off-by: NJaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When the host decides to use a non-resolvable private address, it
must ensure that this generated address does not match the public
address of the controller. Add an extra check to ensure this required
behavior.

In addition rename the variable from urpa to nrpa and fix all of the
comments in the code that use the term unresolvable instead of the
term non-resolvable as used in the Bluetooth specification.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When using Start Service Discovery and when background scanning is used
to report devices, the RSSI is reported or the value 127 is provided in
case RSSI in unavailable.

For Start Discovery the value 0 is reported to keep backwards
compatibility with the existing users.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When no RSSI value is available then make sure that the result is
filtered out when the RSSI threshold filter is active.

This means that all Bluetooth 1.1 or earlier devices will not
report any results when using a RSSI threshold filter.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The mgmt.c file already has a bluetooth_base_uuid variable which has the
exact same value as the reverse_base_uuid one. This patch removes the
redundant variable.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch fixes the Get Connection Information mgmt command to take
advantage of the new cmd_complete callback. This allows for great
simplifications in the logic for constructing the cmd_complete event.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch converts the Get Clock Information mgmt command to take
advantage of the new cmd_complete callback for pending commands.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch converts the Start/Stop Discovery mgmt commands to use the
cmd_complete callback of struct pending_cmd. Since both of these
commands return the same parameters as they take as input we can use the
existing generic_cmd_complete() helper for this.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch updates the Unpair Device code to take advantage of the
cmd_complete callback of struct pending_cmd.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch converts the Pair Device mgmt command to use the new
cmd_complete callback for pending mgmt commands. The already existing
pairing_complete() function is exactly what's needed and doesn't need
changing.

In addition to getting the return parameters always right this patch
actually fixes a reference counting bug and memory leak with the
hci_conn that's attached to the pending mgmt command - something that
would occur when powering off or unplugging the adapter while pairing is
in progress.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch converts the user confirmation & PIN code mgmt commands to
take advantage of the new cmd_complete callback for pending mgmt
commands. The patch also adds a new generic addr_cmd_complete() helper
function to be used with commands that send a mgmt_addr_info response
based on a mgmt_addr_info in the beginning of the command parameters.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch converts the Disconnect mgmt command to take advantage of the
new cmd_complete callback that's part of the pending_cmd struct. There
are many commands whose response parameters map 1:1 to the command
parameters and Disconnect is one of them. This patch adds a
generic_cmd_complete() function for such commands that can be reused in
subsequent patches.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

As preparation for making generic cmd_complete responses possible we'll
need to track the parameter length in addition to just a pointer to
them. This patch adds the necessary variable to the pending_cmd struct.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

We've got a couple of generic scenarios where all pending mgmt commands
are processed and responses are sent to them. These scenarios are
powering off the adapter and removing the adapter. So far the code has
been generating cmd_status responses with NOT_POWERED and INVALID_INDEX
resposes respectively, but this violates the mgmt specification for
commands that should always generate a cmd_complete.

This patch adds support for specifying a callback for the pending_cmd
context that each command handler can use for command-specific
cmd_complete event generation. The actual per-command event generators
will come in subsequent patches.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

In case of failure or when unplugging a controller, the allocated
memory for the UUID list of the discovery filter is not freed. Use
the newly introduced helper for reset the discovery filter and with
that also freeing existing memory.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This patch adds support for the Start Service Discovery command. It
does all the checks for command parameters and configured the discovery
filter settings correctly. However the actual support for filtering
will be added with another patch.
Signed-off-by: NJakub Pawlowski <jpawlowski@google.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The previous patch provided the framework for integrating the UUID
filtering into the service discovery. This patch now provides the
actual filter logic.
Signed-off-by: NJakub Pawlowski <jpawlowski@google.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Using Start Service Discovery provides the option to specifiy a list
of UUID that are used to filter out device found events. This patch
provides the framework for hooking up the UUID filter.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Using Start Service Discovery allows to provide a RSSI threshold. This
patch implements support for filtering out device found events based
on the provided value.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

With the upcoming addition of support for Start Service Discovery, the
discovery handling needs to filter on RSSI and UUID values. For that
they need to be stored in the discovery handling. This patch adds the
appropiate fields and also make sure they are reset when discovery
has been stopped.
Signed-off-by: NJakub Pawlowski <jpawlowski@google.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The actual process of compiling the correct HCI commands for triggering
discovery is something that should be generic. So instead of mixing it
into the Start Discover operation handling, split it out into its own
function utilizing HCI request handling and just providing status in
case of errors or invalid parameters.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Sending the required cmd_complete for the management commands should be
done in one place and not in multiple places. Especially for Start and
Stop Discovery commands this is split into to sending it in case of
failure from the complete handler, but in case of success from the
event state update function triggering mgmt_discovering. This is way
too convoluted and since hci_request serializes the HCI command
processing, send the cmd_complete response from the complete handler
for all cases.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>