tx_desc can be dereferenced as a null pointer when count is passed in
as 0.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Provide support to e1000e for displaying the new format of the PBA found
in the EEPROM.  The unique PBA identifier is no longer restricted to
hexadecimal numbers and must now be read and displayed as a string.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During init, reading the 2 PHY ID registers back-to-back in the default
fast mode could return invalid data (all F's) and in slow mode could
return data to the second read the data from the first read.  To resolve
the issue in fast mode, set to slow mode before any PHY accesses; to
resolve the issue in slow mode, put in a delay for every 82579 PHY access.
Since this PHY is currently only paired with the pch2lan MAC and the PHY
type is not known before the first PHY access which can fail this way,
check for this based on MAC-type.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The LPLU (Low Power Link Up) and Gigabit Disable bits (a.k.a. OEM bits)
were being configured incorrectly when device goes to D3 state.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When link partner is sending continuous Config symbols, the 82571 Serdes
FIFO can overflow resulting in Invalid bit getting set.  To resolve this,
if Sync and Config bits are both 1 ignore the Invalid bit and restart
auto-negotiation.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The workaround function e1000_configure_k1_pchlan() assumes the h/w
semaphore is already acquired.  This was originally missed when setting up
the part for the ethtool loopback test.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Increasing the transmit fifo by 4K (by decreasing the receive fifo size
specified in .pba by the same amount) increases Tx performance.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On certain 82571-based mezzanine NICs in some blade servers, the ethtool
link test can fail due to the serdes_has_link flag not set correctly.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The kernel goes BUG() at the time 'ethtool -p eth0 3' comes
back, which is due to adapter->led_blink_task initialized
several times.  At the time it is still running this results
in a corrupted task_list of the associated workqueue.

The fix is to move the workqueue initialization to the
probe function instead.
Signed-off-by: NHolger Eitzenberger <holger@eitzenberger.org>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some minor cleanup to use string calls that use bound checks just to
be extra safe.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

commit f62bbb5e
ixgbe: Update ixgbe to use new vlan accleration.

removed ETH_FLAG_NTUPLE from the supported flags.

This patch puts it back on to allow for setting ntuple via ethtool.

CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables X540 hardware to use it's own set of support
functions.  This is useful as it has no need of SFP+ support.  A
couple minor bugs with the eeprom semaphore were also cleaned up.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The existing PHY ID for X540 was from early production hardware and
is no longer correct.  This patch corrects that.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on a patch from Jesse Gross.

Enable vlan tag insertion even when vlan group is not configured.

For ixgb HW both CTRL0.VME and VLE bit in the Tx descriptor need to be set
in order to enable HW acceleration.

Introduced separate functions for enabling/disabling of vlan tag stripping
similar to ixgbe.

CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on work by Joe Perches <joe@perches.com>

Using static const to decrease data and overall object size.

CC: Joe Perches <joe@perches.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>

Dean noticed that 'err' wasn't being set when the "goto err_dma"
statement is executed in the following hunk from the commit. It's value
will be zero as a result of a successful call to e1000_init_hw_struct().

This patch changes the error condition to be correctly propagated.

CC: stable@kernel.org
Signed-off-by: NDean Nelson <dnelson@redhat.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update with Intel Wired Ethernet public git trees.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update Intel Wired LAN ixgbevf documentation.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update Intel Wired LAN ixgbe documentation.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update Intel Wired LAN igbvf documentation.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update Intel Wired LAN igb documentation.

v2- Updated the ethtool support link, removed the LRO section and
    anti-spoofing sections.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update Intel Wired LAN e1000e documentation.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update Intel Wired LAN e1000 documentation.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch provides the debugfs facility to the bonding driver.
The "bonding" directory is created in the debugfs root and directories of
each bonding interface (like bond0, bond1...) are created in that.

 # mount -t debugfs none /sys/kernel/debug

 # ls /sys/kernel/debug/bonding
 bond0  bond1
Signed-off-by: NTaku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid Wang <dwang2@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should be returning -EFAULT here.

Mostly this patch is to silence a smatch warning.  The upper levels
of this driver turn all non-zero return values from isar_load_firmware()
into 1.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update vxge driver version to 2.5.1
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NRam Vepa <ram.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Configure the workload clock register and TIM register for independent
interrupt moderation based on the individual vpath utilization instead
of common link utilization.  This greatly improves latency.
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NRam Vepa <ram.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When hot-unplugging a vxge adapter while running, the driver's remove
routine prints warning and then stalls the calling thread.  This is due
to vxge_remove calling vxge_device_unregister to unregister the netdev
before calling flush_scheduled_work clear any pending work.  Swapping
the order of these two functions resolves the issue.
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NRam Vepa <ram.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a workqueue to handle the device reset during a transmit timeout, as
there can be a deadlock during bringup.  Also, set the netif carrier off
before the watchdog reset is started to prevent the timeout from
reoccurring while still processing the first.
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NRam Vepa <ram.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only BAR0 is ever accessed, thus making the calls to pci_request_regions
overkill.  Change calls of pci_request_regions to pci_request_region to
reduce the size of the mapped area.
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NRam Vepa <ram.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling pci_disable_sriov when unloading a SR-IOV physical function
driver from a host when a guest is using a virtual function from that
device can cause a host crash or VM crash.  The crash is caused by the
virtual config space no longer being present when PF is removed (due to
the pci_disable_sriov).  This can be avoided by not calling
pci_disable_sriov to disable the PCI space when shutting down the PF.
Each function in the X3100 operates independently and in this case will
operate properly in the absence of the PF.

Also, added improved logic in the detection of SR-IOV initialization.
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NRam Vepa <ram.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move function locations to remove the need for internal declarations and
other misc clean-ups.
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NArpit Patel <arpit.patel@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The nf_pre_routing functions in bridging have collected two
distinct ways of returning NF_DROP over the years, inline and
via goto.  There is no reason for preferring either one.

So this patch arbitrarily picks the inline variant and converts
the all the gotos.

Also removes a redundant comment.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Various drivers are using implementations of ethtool_ops::get_link
that are equivalent to the default ethtool_op_get_link().  Change
them to use that instead.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While an interface is down, many implementations of
ethtool_ops::get_link, including the default, ethtool_op_get_link(),
will report the last link state seen while the interface was up.  In
general the current physical link state is not available if the
interface is down.

Define ETHTOOL_GLINK to reflect whether the interface *and* any
physical port have a working link, and consistently return 0 when the
interface is down.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support in enic 802.1Qbh port profile provisioning code
to use the mac address set by IFLA_VF_MAC. For now we handle this mac as a
special case for a VM mac address sent to us by libvirt. The VM mac address
is sent to the switch along with the rest of the port profile provisioning
data. This patch also adds calls to register and deregister the mac address
during port profile association/deassociation.
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid Wang <dwang2@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements the ndo_set_vf_mac netdev operation for enic
dynamic devices. It treats the mac address set by IFLA_VF_MAC as a
special case to use it in the port profile provisioning data.
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid Wang <dwang2@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>