The current FIFO low threshold was too low, and caused the FIFO to run
empty when core domain went to INA state between FIFO fills. This patch
increases the low threshold to keep that from happening.

The threshold values depend quite much on the HW and the use cases, so
this should actually be somehow configurable from board files, perhaps.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The code presumed that all ComplexIO interrupts are errors. This is not
the case. This patch adds proper error mask for CIO interrupt handling.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

SMRPS function always sent BTA after sending the SMRPS packet. This is
not needed, and also caused some (buggy) panels to bug. This patch
removes the BTA.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Currently the update area on manual update displays is automatically
enlargened to fully cover scaled overlays. This patch makes that
optional, allowing the panel driver to choose if it's used or not.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Previously a work was started on FRAMEDONE interrupt, and this work
either sent a BTA synchronously or looped until TE_SIZE was zero, to
wait for the end of the transfer.

This patch changes a BTA to be sent asynchronously from FRAMEDONE
interrupt, and when a BTA interrupt is received, the transfer is
finished. This way we do the whole process asynchronously, and also
inside interrupt context.

This will give us much better latency to handle the end of the frame
than with the previous work based solution.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Change dsi_vc_config_l4/vp() to loop for the VC_BUSY flag to change, and
return an error if it fails.

Busy looping is bad, but there's no interrupt that can be used for all the
cases where VC can be busy. So the caller should first try to make sure
that the VC is not busy, if possible, and then call dsi_vc_config_l4/vp().

Most notable case when the caller cannot be sure if the VC is busy is
after frame has been sent. Usually DSI buffers have been emptied until we
need to reconfig the VC, but in some rare cases the VC can still be busy,
and this patch will handle that case.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Once the DSI PLL is separated from the DSI display a full DSI reset will
not be performed every time the display is enabled so the interface and
VCs must be disabled when disabling the display. If the VCs are not
disabled some register accesses will abort.
Signed-off-by: NVille Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The TRM tells us to wait for the DSI PLL derived clocks to become
active before selecting them for use. I didn't actually have any issues
which this would fix but according to the TRM it seems to be the right
thing to do.
Signed-off-by: NVille Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Print an error message if dsi_calc_clock_rates() fails just like it's
done when dispc_calc_clock_rates() fails.
Signed-off-by: NVille Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Do not leave the free running pixel clock enabled if the DSI PLL reset
times out.
Signed-off-by: NVille Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Prepare for supporting panels other than Taal in this driver.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Add support for configuring regulators in the panel specific
configuration data.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The driver will support other panels in addition to Taal, print also the
name.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Add a structure for panel specific configration to be able to support
more than one panel in the future.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Make ESD check usage configurable in DSI panel data, as opposed to a
define.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Get board specific information from the Nokia DSI panel data structure
instead of the DSS.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Introduce a configuration struct for platform/board specific information
of Nokia DSI command mode panels, to be used in addition to struct
omap_dss_device (passed via the 'void *data' member).
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Add gpio irq based external TE support with timeout.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Switch from numbered to named labels to make it easier to add new
labels for error handling.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Move ESD work queuing and cancelling out of taal_power_on/off() to avoid
problems related to taal_esd_work() calling the power on/off functions.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Change state only if power on was succesful.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Move dsi_bus_lock/unlock() out of taal_power_on/off() to avoid deadlock
in taal_esd_work().
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Bail out from taal_enable_te() and taal_run_test() if panel is not
enabled.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Check return values and bail out on errors.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

ESD work is never queued in probe, no need to cancel it on probe error.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Separate gpio_request() and request_irq() error handling.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

After the addition of proper hardware reset, taal_hw_reset(), there's no
need for an additional platform enable/disable. Remove them.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Avoid potential race conditions in sysfs access to taal data.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Issue a proper reset pulse on the reset line instead of just doing power
on/off.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

taal_bl_update_status was missing locks to protect taal_data. This caused
a kernel crash randomly, as the code attempted to set the brightness while
the OMAP's DSI block was actually disabled.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Using nanoseconds as arguments to functions that set the DSI timeouts was
perhaps not so good idea. The timeouts are based on different DSI clocks,
so the possible range for the timeouts vary greatly depending on the
clocks. Also, the multipliers used with the timeouts cause big gaps in the
timeout range, meaning that the nanosecond based functions could cause the
timeout to be quite far from the intended value.

This patch changes the functions to take the plain tick values with the
multiplier enable/disable bits, and sets the TA/LP_RX/HS_TX timeouts to
maximum. While the timeouts could be much lower, the fact is that when
TA/LP_RX/HS_TX timeout happens, we are in an error situation and not in a
hurry anyway.

STOP_STATE_COUNTER is a different matter, but it is only used at
initialization time, and won't normally affect the performance.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Check if the peripheral answered something, and if so, dump the data
and return an error.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Change dsi_vc_dcs_read_2() data parameter to two u8 parameters to make the
byte-order clear.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Using the shared workqueue led to to a deadlock in the case where the
display was unblanked via keyboard.

What happens is something like this:

- User presses a key

context 1:
- drivers/char/keyboard.c calls schedule_console_callback()
- fb_unblank takes the console semaphore
- dsi bus lock is taken, and frame transfer is started (dsi bus lock is
  left on)
- Unblank code tries to set the panel backlight, which tries to take dsi
  bus lock, but is blocked while the frame transfer is going on

context 2, shared workqueue, console_callback in drivers/char/vt.c:
- Tries to take console semaphore
- Blocks, as console semaphore is being held by context 1
- No other shared workqueue work can be run

context 3, HW irq, caused by FRAMEDONE interrupt:
- Interrupt handler schedules framedone-work in shared workqueue
- Framedone-work is never ran, as the shared workqueue is blocked. This
  means that the unblank thread stays blocked, which means that context 2
  stays blocked.

While I think the real problem is in keyboard/virtual terminal code, using
a private workqueue in the DSI driver is perhaps safer and more robust
than using the shared one. The DSI works should not be delayed more than a
millisecond or so, and even if the private workqueue gives us no hard
promise of doing so, it's still safer bet than the shared workqueue.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

dsi_vc_flush_receive_data() is meant to dump data when something has gone
wrong, and thus we should use DSSERR, not DSSDBG.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Trigger WARN_ON() messages from various places in the code in case the
memory region is not currently locked.
Signed-off-by: NVille Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

When more than one memory region needs to be lockd at the same time use
the memory region id to fix the order in which the locks are taken. Also
one needs to use the _nested() versions of the locking primitives. The
memory region id can serve as the lock class there as well.
Signed-off-by: NVille Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

R/W semaphore is a good fit for the memory region locking pattern.
So use it.
Signed-off-by: NVille Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Add locking to the memory regions to make sure the memory region size
won't be changed while some other piece of code is performing some
checks or setup based on that information.
Signed-off-by: NVille Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Separate the memory region from the framebuffer device a little bit.
It's now possible to select the memory region used by the framebuffer
device using the new mem_idx parameter of omapfb_plane_info. If the
mem_idx is specified it will be interpreted as an index into the
memory regions array, if it's not specified the framebuffer's index is
used instead. So by default each framebuffer keeps using it's own
memory region which preserves backwards compatibility.

This allows cloning the same memory region to several overlays and yet
each overlay can be controlled independently since they can be
associated with separate framebuffer devices.
Signed-off-by: NVille Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>