This driver handles only L2TP data frames; control frames are handled
by a userspace application. It implements L2TP using the PPPoX socket
family. There is a PPPoX socket for each L2TP session in an L2TP
tunnel.  PPP data within each session is passed through the kernel's
PPP subsystem via this driver. Kernel parameters of each socket can be
read or modified using ioctl() or [gs]etsockopt() calls.
Signed-off-by: NJames Chapman <jchapman@katalix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hi,

This is the third submission of the network driver for PS3.
The differences from the previous one are:

  - renamed source file names so that their prefix can match
    with the module name
  - added cbe-oss-dev@ozlabs.org line for MAINTAINER file
  - changed some in copyright comments

If there are no more comments, please apply for 2.6.23.

Thank you

--
Subject: PS3: Ethernet driver

From: Masakazu Mokuno <mokuno@sm.sony.co.jp>

Add Gigabit Ethernet support for the PS3 game console.  The module will
be called ps3_gelic.

CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NMasakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

It needs writesb(), not available on all platforms.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Unmaintained, superceded by skge.

Prodded to deletion by Adrian Bunk.  Acked by Stephen Hemminger.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Support for the Asix AX88796 network controller, an
NE2000 compatible 10/100 ethernet device with internal
PHY.

The driver supports PHY settings via either ioctl() or
the ethtool driver ops.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NFranck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 delete mode 100644 arch/mips/configs/ocelot_c_defconfig
 delete mode 100644 arch/mips/momentum/ocelot_c/Makefile
 delete mode 100644 arch/mips/momentum/ocelot_c/cpci-irq.c
 delete mode 100644 arch/mips/momentum/ocelot_c/dbg_io.c
 delete mode 100644 arch/mips/momentum/ocelot_c/irq.c
 delete mode 100644 arch/mips/momentum/ocelot_c/ocelot_c_fpga.h
 delete mode 100644 arch/mips/momentum/ocelot_c/platform.c
 delete mode 100644 arch/mips/momentum/ocelot_c/prom.c
 delete mode 100644 arch/mips/momentum/ocelot_c/reset.c
 delete mode 100644 arch/mips/momentum/ocelot_c/setup.c
 delete mode 100644 arch/mips/momentum/ocelot_c/uart-irq.c
 delete mode 100644 arch/mips/pci/fixup-ocelot-c.c
 delete mode 100644 arch/mips/pci/pci-ocelot-c.c

Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add an optional debug interface for displaying state of transmit/receive
rings. Creates a file debugfs/sky2/ethX for each device that is up.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Changes to last version:
- spelling fix
- cleaned up probe code

Thomas.

Ethernet driver for EISA only SNI RM200/RM400 machines
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

CONFIG_NETDEVICES, CONFIG_NET_ETHERNET:
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.

CONFIG_SMC9194:
Move it so that it appears correctly in menuconfig.
Signed-off-by: NJan Engelhardt <jengelh@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The EMAC driver, in drivers/net/ibm_emac, for the embedded Ethernet
MAC found in PowerPC 4xx embedded chips is not suitable for
arch/powerpc.  It will not build because it relies on the old arch/ppc
OCP mechanism.  BenH has a new, device-tree aware version of the
driver which will work in arch/powerpc, but until it's merged, this
patch will disable the old, non-building version.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

ucc_geth has been migrated to use the common phylib code. So lets add a
'select PHYLIB' to the UCC_GETH Kconfig entry.
Signed-off-by: NJan Altenberg <jan.altenberg@linutronix.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Hi,

This patch has removed unnecessary dependency on VIA velocity config.

Yoichi
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The UCC_GETH Kconfig option in drivers/net/Kconfig had a line to select the
UCC_FAST option is arch/powerpc/sysdev/qe_lib/Kconfig, which is only used
on PowerPC builds.  On other architectures, this would generated a warning.
The fix is to have UCC_FAST depend on UCC_GETH.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

CONFIG_MLX4_DEBUG works out to a def_bool y for those that have 
CONFIG_EMBEDDED set.  Make it depend on MLX4_CORE.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch creates platform_device entries for the Marvell mv64x60
ethernet controller ports, based on information contained in the
device tree.

This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures.  Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: NJan Engelhardt <jengelh@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

It is preferable to group drivers by usage (net, scsi, ATA, ...) than
by bus.  When reviewing drivers, the [PCI|USB|PCMCIA|...] maintainer
is probably less qualified on networking issues than a networking
maintainer.  Also, from a practical standpoint, chips often
appear on multiple buses, which is why we do not put drivers into
drivers/pci/net.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add an InfiniBand driver for Mellanox ConnectX adapters.  Because
these adapters can also be used as ethernet NICs and Fibre Channel 
HBAs, the driver is split into two modules: 
 
  mlx4_core: Handles low-level things like device initialization and 
    processing firmware commands.  Also controls resource allocation 
    so that the InfiniBand, ethernet and FC functions can share a 
    device without stepping on each other. 
 
  mlx4_ib: Handles InfiniBand-specific things; plugs into the 
    InfiniBand midlayer. 
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

PHY support for pasemi_mac.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch lets RBTX49XX boards use generic platform_driver interface
for the ne driver.

* Use platform_device to pass ioaddr and irq to the ne driver.
* Remove unnecessary ifdefs for RBTX49XX from the ne driver.
* Make the ne driver selectable on these boards regardless of CONFIG_ISA
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

As SMC91X ethernet controller are used in blackfin STAMP 533 development
board, this patch add blackfin support to the smc91x linux driver.
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a race condition in the transmit code, where the dma interrupt could update
the free tx buffer count concurrently and wedge the tx queue.

Fix the misuse of the rx frame status and rx frame length registers: no more
"fifo overrun" errors caused by the OFLOW bit being tested in the frame length
register (instead of the status register), and no more missed packets due to
incorrect length taken from status register (instead of the frame length
register).

Fix a panic (skb_over_panic BUG) caused by allocating and then copying an
incoming packet while the packet length register was changing.

Cut-and-paste the reset code from the powermac mace driver (mace.c), so the NIC
functions when MacOS does not initialise it (important for anyone wanting to
use the Emile boot loader).

Cut-and-paste the error counting and timeout recovery code from mace.c.

Fix over allocation of rx buffer memory (it's page order, not page count).

Converted to driver model.

Converted to DMA API.

Since I've run out of ways to make it fail, and since it performs well now,
promote the driver from EXPERIMENTAL status. Tested on both quadra 840av and
660av.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Macintosh CS89x0 Ethernet: Netif updates
Addition of netif_stop_queue() before transmission by Michael Schmitz
skb_copy_{from,to}_linear_data() conversion by Geert Uytterhoeven
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Documentation/modules.txt doesn't exist, but
Documentation/kbuild/modules.txt does.

Signed-off-by: Alexander E. Patrakov
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Get rid of the CONFIG_NETPOLL_RX option completely since all the
dependencies have been removed long ago...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: NJeff Garzik <jgarzik@pobox.com>
Acked-by: NMatt Mackall <mpm@selenic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Transmit on Demand: Fix spelling in config option, and make it actually enable TOD.
Signed-off-by: NMichael Reiss <michael.f.reiss@freescale.com>
Signed-off-by: NMichael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

migrate ucc_geth to use the common phylib code.

There are several side effects from doing this:

o deprecate 'interface' property specification present
  in some old device tree source files in
  favour of a split 'max-speed' and 'interface-type'
  description to appropriately match definitions
  in include/linux/phy.h.  Note that 'interface' property
  is still honoured if max-speed or interface-type
  are not present (backward compatible).
o compile-time CONFIG_UGETH_HAS_GIGA is eliminated
  in favour of probe time speed derivation logic.
o adjust_link streamlined to only operate on maccfg2
  and upsmr.r10m, instead of reapplying static initial
  values related to the interface-type.
o Addition of UEC MDIO of_platform driver requires
  platform code add 'mdio' type to id list
  prior to calling of_platform_bus_probe (separate patch).
o ucc_struct_init introduced to reduce ucc_geth_startup
  complexity.
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Current tc35815 driver is very obsolete and less maintained for a long
time.  Replace it with a new driver based on one from CELF patch
archive.

Major advantages of CELF version (version 1.23, for kernel 2.6.10) are:

* Independent of JMR3927.
  (Actually independent of MIPS, but AFAIK the chip is used only on
   MIPS platforms)
* TX4938 support.
* 64-bit proof.
* Asynchronous and on-demand auto negotiation.
* High performance on non-coherent architecture.
* ethtool support.
* Many bugfixes and cleanups.

And improvoments since version 1.23 are:

* TX4939 support.
* NETPOLL support.
* NAPI support. (disabled by default)
* Reduce memcpy on receiving.
* PM support.
* Many cleanups and bugfixes.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Gianfar needs crc32 to be selected to compile.
Signed-off-by: NDave Jiang <djiang@mvista.com>

--
 drivers/net/Kconfig |    1 +
 1 files changed, 1 insertions(+), 0 deletions(-)
--
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Change the Kconfig files so that the Freescale QE options are automatically
selected if a QE device is selected.  Previously, you'd need to manually
select UCC_FAST if you want any "fast" UCC devices, such as Gigabit Ethernet.
Now, the QE Gigabit Ethernet option is always available if the device has a
QE, and UCC_FAST is automatically enabled.  A side-effect is that the
"QE Options" menu no longer exists.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Use tabs instead of white spaces for CHELSIO_T3 entry.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The driver attempts to upgrade the FW if the card has the wrong version.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch adds or changes some HW specific settings for spider_net on
Celleb.
Signed-off-by: NKou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Remove the use of CONFIG_MV643XX_ETH_[012] variables on most platforms.
Instead, platform-specific code enables the ports supported by the
hardware.  After this patch, these config variables are only used in
arch/ppc, so also move them from drivers/net/Kconfig to arch/ppc/Kconfig.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Acked-by: NJeff Garzik <jeff@garzik.org>
Cc: Paul Mackerras <paulus@samba.org>

sk98lin is scheduled for removal in July 2007. This patch makes the
deprecation more obvious in the configuration interface. FWIW, Gentoo have
been shipping a patch very similar to this for a long time.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Remove the experimental tag for the pcnet32 NAPI implementation.
Signed-off-by: NDon Fry <pcnet32@verizon.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>