Add PnP support to radio-sf16fmr2 driver to support SF16-FMD2 card (SB16 +
TEA5757). The driver can now handle two cards (FMR2 is hardwired to 0x384,
FMD2 can be put at 0x384 or 0x284 by PnP).
Tested with both SF16-FMR2 and SF16-FMD2 (the can work at the same time by
using kernel parameter "pnp_reserve_io=0x384,2" so the FMD2 is put at 0x284).
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for uncompressed 8-bit raw bayer formats.
Signed-off-by: NSakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Implement more generic quirk registers than just limit and capability
registers. This comes with the expense of a little bit more access time so
these should be only used when really needed.
Signed-off-by: NSakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some sensors do use binning but do not have valid limits in binning
registers. Use non-binning limits in that case.
Signed-off-by: NSakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

rval was not properly initialised in smiapp_read_nvm(). Do that.
Signed-off-by: NSakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The pre_pll divisor must be such that ext_clk / pre_pll divisor does not
result in a frequency that is greater than pll_ip_clk_freq. Fix this.
Signed-off-by: NSakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some sensors only allow 8-bit access, so use safe 8-bit access before the
sensor has been identified.
Signed-off-by: NSakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some sensors implement only 8-bit read functionality and fail on wider
reads. Add a quirk flag for such sensors.
Signed-off-by: NSakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Pass struct sensor to register access commands. This allows taking quirks
into account in register access.
Signed-off-by: NSakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Instead of providing a function in platform data, allow also providing the
name of the external clock and use it through the clock framework.
Signed-off-by: NSakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Report SNR in 0.1 dB scale instead of raw hardware register values.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gspca_pac7302 module supports the webcam with usb id: 093a:2627.
It is a Genius FaceCam 300.
The module does not need any changes but listing the usb id along with a vertical flip flag.
The included patch adds this to the module source.
Signed-off-by: NJozsef Marton <jmarton@users.sourceforge.net>
Acked-by: NMárton Németh <nm127@freemail.hu>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Continuous flip of bit2 reg 0x70 can cause device to become unresponsive.

Also correct reg read mistake.
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Trival patch to get it working with my cards stuff.
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Acked-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This device supports V4L2_STD_ALL, but its check for 60Hz standards
is broken, as NTSC is not the only standard that uses 60Hz.

Cc: Federico Vaga <federico.vaga@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

V4L2 driver for the Video Input Port within STA2X11 board
Signed-off-by: NFederico Vaga <federico.vaga@gmail.com>
Acked-by: NGiancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NFederico Vaga <federico.vaga@gmail.com>
Acked-by: NGiancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Video user controls such as brightness, contrast, saturation, and
hue are now handled.
Signed-off-by: NFederico Vaga <federico.vaga@gmail.com>
Acked-by: NGiancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

fintek-cir, ite-cir and nuvoton-cir may try to free an I/O region
and/or IRQ handler that was never allocated after a failure in their
respective probe functions.  Add and use separate labels on the
failure path so they will do the right cleanup after each possible
point of failure.

Compile-tested only.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Correct incorrect scancode for KEY_1
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There are many different Medion X10 remotes that need slightly different
keymaps. We may not yet have all the needed keymaps, in which case a
wrong keymap may be used. This happened with Medion X10 OR2x remotes
before the keymap for them was added, causing the ati_remote driver to
select the Medion Digitainer keymap instead. Unfortunately, the Medion
Digitainer keymap doesn't have the standard X10 up/down scancodes
assigned to KEY_UP and KEY_DOWN keycodes, making wrongly assigned
remotes mostly unusable.

Add the regular KEY_UP and KEY_DOWN scancodes to the Medion X10
Digitainer keymap, making any Medion remote mostly usable even when
wrongly used with that keymap (standard buttons, such as
up/down/left/right, 0-9, play/stop/pause, have the same scancode in all
the X10 remotes).
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add another Medion X10 remote keymap. This is for the Medion OR2x
remotes with the Windows MCE button.

The receiver shipped with this remote has the same USB ID as the other
Medion receivers, but the name is different and is therefore used to
detect this variant.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch were applied by mistake, as it were rejected by Don, who
requested it to be broken into per-change patches.

This reverts commit 0982db20.

Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Volokh Konstantin <volokh84@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There was a warning when ran "make versioncheck"

drivers/staging/media/as102/as102_fe.c: 20 linux/version.h not needed.
Signed-off-by: Njoseph daniel <josephdanielwalter@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The card is similar to TeVii s470, but has different LNB power control.
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The Logitech pan/tilt reset UVC control contains two V4L2 button
controls to reset pan and tilt. As the UVC control is not marked as
auto-update, the button bits are set but never reset. A pan reset that
follows a tilt reset would thus reset both pan and tilt.

Fix this by not caching the control value of write-only controls. All
standard UVC controls are either readable or auto-update, so this will
not cause any regression and will not result in extra USB requests.
Reported-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Tested with Yfeng 680 ATV dongle.
Signed-off-by: NIsmael Luceno <ismael.luceno@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This issuses applyed only for Adlink MPG24 board with go7007
 & wis2804, all whese changes was tested for continuos
 load&restart mode

This is minimal changes needed for start up go7007&wis2804 to work correctly
  in 3.4 branch

Changes:
  - When go7007 reset device, i2c was not worked (need rewrite GPIO5)
  - As wis2804 has i2c_addr=0x00/*really*/, so Need set I2C_CLIENT_TEN flag for validity
  - some main nonzero initialization, rewrites with kzalloc instead kmalloc
  - STATUS_SHUTDOWN was placed in incorrect place, so if firmware wasn`t loaded, we
    failed v4l2_device_unregister with kernel panic (OOPS)
  - some new v4l2 style features as call_all(...s_stream...) for using subdev calls
  - wis-tw2804.ko module code was incompatible with 3.4 branch in initialization v4l2_subdev parts.
    now i2c_get_clientdata(...) contains v4l2_subdev struct instead non standart wis_tw2804 struct

Adds:
  - Additional chipset tw2804 controls with: gain,auto gain,inputs[0,1],color kill,chroma gain,gain balances,
    for all 4 channels (from tw2804.pdf)
  - Power control for each 4 ADC (tw2804) up when s_stream(...,1), down otherwise
Signed-off-by: NVolokh Konstantin <volokh84@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Demod needs some time to wake up after power on.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

to prevent I/O errors...
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Reports value as a 0.1 dB.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

UIO-2 and UIO-3 were broken.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Changes compared to version 0.1 of driver (sent 6 May):
- Initial implementation of get_rf_strength function.
- Introduction of a warning message
Signed-off-by: NHans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Changes compared to version 0.5 of driver (sent 6 May):
- Initial implementation of get_rf_strength function.
Signed-off-by: NHans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Support for tuner Fitipower FC0013
Signed-off-by: NHans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>