This patch adds support for APB0 in H3. It seems to be compatible with
earlier SOCs. apb0 gates controls R_ block peripherals (R_PIO, R_IR,
etc).

Since this gates behave just like any Allwinner clock gate, add a generic
compatible that can be reused if we don't have any clock to protect.
Signed-off-by: NKrzysztof Adamski <k@japko.eu>
[Maxime: Removed the H3 compatible from the simple-gates driver, reworked
         the commit log a bit]
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

A83T has similar bus gates that of H3, including single gating register has
different clock parent.

As per H3 and A83T datasheet, usbhost is under AHB2.

However,below shows allwinner source code assignment:
bits: 26 (ehci0), 27 (ehci1), 29 (ohci0) => AHB1 for A83T.
bits: 26 (ehci0), 27 (ehci1) => AHB1 for H3
bits  29, 30, 31(ohci0,1,2) => AHB2 for H3.

until, this confusion is cleared keep it H3 way.
Signed-off-by: NVishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

APB0 is part of PRCM, and is compatible with earlier SOCs.
apb0 gates controls R_PIO, R_UART, R_RSB, etc clocks.
This patch adds support for APB0 gates for A83T.
Signed-off-by: NVishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The video engine has its own special module clock, consisting of a clock
gate, configurable dividers, and a reset control.

On later (sun[68]i) families, the reset control is moved out of this
piece of hardware and grouped with reset controls of other peripherals.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Tested-by: NJens Kuske <jenskuske@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The H3 clock control unit is similar to the those of other sun8i family
members like the A23.

It adds a new bus gates clock similar to the simple gates, but with a
different parent clock for each single gate.
Some of the gates use the new AHB2 clock as parent, whose clock source
is muxable between AHB1 and PLL6/2. The documentation isn't totally clear
about which devices belong to AHB2 now, especially USB EHIC/OHIC, so it
is mostly based on Allwinner kernel source code.
Signed-off-by: NJens Kuske <jenskuske@gmail.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A10/A20 share the same set of DRAM clock gates, which controls
direct memory access for some peripherals.

On the A10, bit 15 controls the system's DRAM clock output (possibly
to the DRAM chips), which we need to keep on.

On the A20 this has been moved to the DRAM controller, becoming a no-op.
However it is still listed in the user manual, so add it anyway.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The "cpus" clock is the clock for the embedded processor in the A80.
It is also part of the PRCM clock tree. This clock includes a pre-
divider on one of its inputs. For now we are using a custom clock
driver for it. In the future we may want to develop a generalized
driver for these types of clocks, which also includes the AHB clock
driver on sun[5678]i.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This patch adds support for the PRCM apbs clock gates found on the
Allwinner A80 SoC.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The H3 has a usb-phy clk register which is similar to that of earlier
SoCs, but with support for a larger number of phys. So we can simply add
a new set of clk-data and a new compatible and be done with it.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NReinder de Haan <patchesrdh@mveas.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The usb-clk on sun8i a23 and a33 SoCs is similar to the ones found
on sun6i-a31 SoCs but instead of a 3th phy the a23 / a33 have a hsic
interface which gets enabled by almost the same bits as used on
the a31 for the 3rd phy, but not exactly the same bits so we need
a new compatible for this.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NChen-Yu Tsai <wens@csie.org>

The AHB clock on sun5i and sun7i are muxable divider clocks.
Use a factors clock to support them.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The USB controller/phy clocks and reset controls are in a separate
address block, unlike previous SoCs where they were in the clock
controller. Also, access to the address block is controlled by a
clock gate to AHB.

Add support for resets requiring a clock to be enabled when
asserting/deasserting the reset controls, and add the sun9i USB
clocks.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

On the A80 SoC, the 4 mmc controllers each have a separate register
controlling their register access clocks and reset controls. These
registers in turn share a ahb clock gate and reset control.

This patch adds a platform device driver for these controls. It
requires both clocks and reset controls to be available, so using
CLK_OF_DECLARE might not be the best way.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The module 0 style clocks, or storage module clocks as named in the
official SDK, are almost the same as the module 0 clocks on earlier
Allwinner SoCs. The only difference is wider mux register bits.

As with earlier Allwinner SoCs, mmc module clocks are a special case
of mod0 clocks, with phase controls for 2 child clocks, output and
sample.

This patch adds support for both.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Instead of having three different clocks for the main MMC clock and the two
phase sub-clocks, which involved having three different drivers sharing the
same register, rework it to have the same single driver registering three
different clocks.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NChen-Yu Tsai <wens@csie.org>
Tested-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMike Turquette <mturquette@linaro.org>

This patch unifies the sun6i AHB1 clock, originally supported
with separate mux and divider clks. It also adds support for
the pre-divider on the PLL6 input, thus allowing the clock to
be muxed to PLL6 with proper clock rate calculation.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Some clock modules on the A31 use PLL6x2 as one of their inputs.
This patch changes the PLL6 implementation for A31 to a divs clock,
i.e. clock with multiple outputs that have different dividers.
The first output will be the normal PLL6 output, and the second
will be PLL6x2.

This patch fixes the PLL6 N factor in the clock driver, and removes
any /2 dividers in the PLL6 factors clock part. The N factor counts
from 1 to 32, mapping to values 0 to 31, as shown in the A31 manual.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This driver does not match the hardware, which is actually compatible
to sun4i-a10-apb1-clk. Since we've switch to the correct one, drop
this driver.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This commit unifies the APB1 mux with the APB1 clock, using the new
factors infrastructure.
Signed-off-by: NEmilio López <emilio@elopez.com.ar>
[wens@csie.org: Add mux mask bits]
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This adds the gate clocks for AHB/APB busses on the A80 SoC.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A80 SoC has 12 PLL clocks, 3 AHB clocks, 2 APB clocks, and a
new "GT" bus, which I assume is some kind of data bus connecting
the processor cores, memory and various busses. Also there is a
bus clock for a ARM CCI400 module.

As far as I can tell, the GT bus and CCI400 bus clock must be
protected.

This patch adds driver support for peripheral related PLLs and
bus clocks on the A80. The GT and CCI400 clocks are added as well
as these 2 along with the PLLs they are clocked from must not be
disabled.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The MBUS clock on sun8i is slightly different from the old mod0 clocks.
The divider is 3 bits wider, while also needing a divider table for the
higher 4 values, which all set the same divider.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The MMC clock we thought we had until now are actually not one but three
different clocks.

The main one is unchanged, and will have three outputs:
  - The clock fed into the MMC
  - a sample and output clocks, to deal with when should we output/sample data
    to/from the MMC bus

The phase control we had are actually controlling the two latter clocks, but
the main MMC one is unchanged.

We can adjust the phase with a 3 bits value, from 0 to 7, 0 meaning a 180 phase
shift, and the other values being the number of periods from the MMC parent
clock to outphase the clock of.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>

Even though the mbus clock is a regular module clock, given its nature, it
needs to be enabled all the time.

Introduce a new compatible, to differentiate it from the other module clocks.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>

This patch adds "allwinner,sun8i-a23-apb0-gates-clk", a A23 specific
compatible to the sun6i-a31-apb0-gates clock driver, along with the
gate bitmap.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A23 has an almost identical PRCM clock tree. The difference in
the APB0 clock is the smallest divisor is 1, instead of 2.

This patch adds a separate sun8i-a23-apb0-clk driver to support it.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The clock control unit on the A23 is similar to the one found on the A31.

The AHB1, APB1, APB2 gates on the A23 are almost identical to the ones
on the A31, but some outputs are missing.

The main CPU PLL (PLL1) however is like that on older Allwinner SoCs,
such as the A10 or A20, but the N factor starts from 1 instead of 0.

This patch adds support for PLL1 and all the basic clock muxes and gates.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Document new compatible strings for clock provided by the PRCM
(Power/Reset/Clock Management) unit.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: NEmilio López <emilio@elopez.com.ar>

Support for the USB gates and resets on A31 has been recently added
using a new compatible, so let's document it here.
Signed-off-by: NEmilio López <emilio@elopez.com.ar>

The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the clock driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NEmilio López <emilio@elopez.com.ar>

The Allwinner A20/A31 clock module controls the transmit clock source
and interface type of the GMAC ethernet controller. Model this as
a single clock for GMAC drivers to use.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NEmilio López <emilio@elopez.com.ar>

The A31 has a slightly different PLL6 clock. Add support for this new clock in
our driver.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NEmilio López <emilio@elopez.com.ar>

Add register definitions for the usb-clk register found on sun4i, sun5i and
sun7i SoCs.
Signed-off-by: NRoman Byshko <rbyshko@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NEmilio López <emilio@elopez.com.ar>

clock-output-names is now required for most of sunxi clock nodes, to
provide the name of the corresponding clock. Add the new requirements,
exceptions, as well as examples.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NEmilio López <emilio@elopez.com.ar>

This patch adds support for the external clock outputs on the
Allwinner A20 SoC. The clock outputs are similar to "module 0"
type clocks, with different offsets and widths for clock factors.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NEmilio López <emilio@elopez.com.ar>

This commit implements support for the "module 0" type of clocks, as
used by MMC, IR, NAND, SATA and other components.
Signed-off-by: NEmilio López <emilio@elopez.com.ar>
Acked-by: NMike Turquette <mturquette@linaro.org>

This commit implements PLL5 and PLL6 support on the sunxi clock driver.
These PLLs use a similar factor clock, but differ on their outputs.
Signed-off-by: NEmilio López <emilio@elopez.com.ar>
Acked-by: NMike Turquette <mturquette@linaro.org>

This commit adds gating support to PLL1 on the clock driver. This makes
the PLL1 implementation fully compatible with PLL4 as well.
Signed-off-by: NEmilio López <emilio@elopez.com.ar>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NMike Turquette <mturquette@linaro.org>

That documentation was mostly useful when we didn't have any
documentation for those SoCs, which is not the case anymore. Remove
this, since it should live in the DT anyway.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Cc: Mark Rutland <mark.rutland@arm.com>

The Allwinner A20 is almost identical to the earlier A10 SoC from
Allwinner on many aspects, including the clocks tree. However, since the
A20 has some additionnal IPs compared to the A10, the clock tree isn't
exactly the same, especially when it comes to the gated clocks
available. We thus need to register different clock gates for the A20.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NEmilio López <emilio@elopez.com.ar>