The functions do not exist, so remove the prototypes.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Use strtobool and kstrto* functions when parsing sysfs inputs.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add OMAP_DSS_OVL_CAP_GLOBAL_ALPHA and OMAP_DSS_OVL_CAP_PRE_MULT_ALPHA to
overlay capabilities. Use these instead of FEAT_GLOBAL_ALPHA,
FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA in code.

Remove FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA which are no
longer used. FEAT_GLOBAL_ALPHA is still used to decide if the HW has
global alpha register.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NArchit Taneja <archit@ti.com>

Add support to define overlay capabilities into dss_features. The
features are set to overlay->caps at initialization time.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NArchit Taneja <archit@ti.com>

Use lookup tables instead of switch/if in some DISPC functions to make
the code cleaner.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NArchit Taneja <archit@ti.com>

Remove support for non-DISPC overlays and overlay managers.

The support to possibly have non-DISPC overlays and managers was made to
make it possible to use CPU and/or sDMA to update RFBI or DSI command
mode displays. It is ok to remove the support, because:

- No one has used the feature.
- Display update without DISPC is very slow, so it is debatable if the
  update would even be usable.
- Removal cleans up code.
- If such a feature is needed later, it is better implemented outside
  omapdss driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NArchit Taneja <archit@ti.com>

DSS driver has not been "experimental" for many years now, so perhaps
it's time to remove the text from Kconfig titles.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Currently when changing the manager of an overlay, set_manager() directly
calls dispc to set the overlay's destination.

Change this to be more in line with other overlay configurations, and
this will also remove the need to have dispc clocks enabled when calling
set_manager().

A new field is added to overlay struct, "manager_changed". This is
similar to "display_changed" field in manager struct, and is used to
inform apply that the manager has changed and thus write to the
registers is needed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DPI and DSI were not cleaning up the clock source in error or uninit
cases. Set the clock source back to PRCM.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

dsi_mux_pads() needs to know about the DSI HW module and the DSI lanes
used. Split the function into two, enable and disable, which take
necessary arguments, and add empty implementations for both.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Currently, there are 2 differently named platform devices generated for
the 2 DSS DSI modules. In order to use the same driver, the dsi devices
should be 2 instances of the same platform device.

Change the platform device names from "omapdss_dsi1" and "omapdss_dsi2"
to omapdss_dsi", and set the device indices to 0 and 1.
Signed-off-by: NArchit Taneja <archit@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that the HWMOD fmwk handles the fcks of DSS modules properly, the
DSS driver no longer needs to explicitely enable/disable the fck.

This patch removes the enables/disables of fck from dispc, dsi and dss.
The clk_get(fck) is still needed there, as the modules need to know the
frequency of the clock.

For hdmi and venc this patch also removes the clk_get(fck), as they
don't need the clock at all.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This reverts commit df5d3ed2.

The HDMI clock name has been fixed in HWMOD data.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This reverts commit 9ede365a.

The hack is no longer needed, as the HWMOD data has been fixed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The array size of fifo_size array in the global dispc struct is currently
hardcoded to 3. Replace this with the MAX_DSS_OVERLAYS macro in dss_features.h,
use dss_features function to get the number of overlays instead of the
ARRAY_SIZE macro in dispc_read_plane_fifo_sizes().
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Iterate over overlay id's to shorten _dispc_set_color_conv_coef()
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Iterate over manager and overlay id's to shorten dispc_save_context() and
dispc_restore_context().
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Iterate over manager and overlay id's to shorten dispc_dump_regs().
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Prepare dispc_dump_regs() to iterate over manager and overlay id's. Doing this
requires modifications of the macro "DUMPREG" which currently needs us to specify
the manager/overlay name to get the correct result. For example, in order to
print the register DISPC_TIMING_H(OMAP_DSS_CHANNEL_LCD), we can't iterate over
a varaible i and get the desired result through DUMPREG(DISPC_TIMING_H(i)).

Split the registers into 3 sections, the first with no arguments(common
registers), the second with one argument(manager/overlay id), and the third with
two arguments(overlay id and coefficient index), redefine DUMPREG macros for
each of these.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

There's no guarantee that the error handler worker thread
will run while the dispc clocks are on. Explicitly enable/disable
them.
Signed-off-by: NDima Zavin <dima@android.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

If a manager is moved while attached to an enabled display, the DSS
system will be left in an inconsistent state. This will eventually cause
a kernel oops when the enabled display is disabled.

Fix this by not allowing the user to move a manager away from an enabled
display.
Signed-off-by: NDaniel Morsing <daniel.morsing@gmail.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

None of the DSS interface drivers check if an overlay manager is
connected to the display when the display is being enabled. This leads
to null pointer crash if the display has no manager.

This patch checks for the manager and returns an error if it is null.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The HDMI clock (hdmi_clk) is missing in the current OMAP4 HWMOD
database. Fix this in the DSS driver by using the old clock name
(dss_48mhz_clk).
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The HWMOD data for OMAP2 and 3 are currently not up to date regarding
DSS (OMAP4 HWMOD data is fine). This patch makes the DSS driver to get
the opt clocks needed for OMAP2/3 with the old clock names, thus
allowing DSS driver to use runtime PM.

The HWMOD databases should be fixes ASAP, and this patch can be reverted
after that.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The current method of saving and restoring the context could cause a
restore before saving, effectively "restoring" zero values to registers.

Add ctx_valid field to indicate if the saved context is valid and can be
restored.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The current method of saving and restoring the context could cause a
restore before saving, effectively "restoring" zero values to registers.

Add ctx_valid field to indicate if the saved context is valid and can be
restored.

Also restructure the code to save the ctx_loss_count in save_context(),
which makes more sense than the previous method of storing new
ctx_loss_count in dispc_need_ctx_restore.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

dss.c only saves 1 register (3 in OMAP3) so the extra overhead from
need_ctx_restore & co. is probably bigger than the time spent saving and
restoring those few registers every time.

So remove the code from dss.c and restore context every time dss has
been off.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

dispc.c enables and disables clocks in almost every function to make
sure the clocks are enabled when the function is called. This is rather
unoptimal way to handle the problem.

With pm_runtime other components have to call dispc_runtime_get() to
enable dispc clocks before calling any other dispc functions. Thus the
finegrained clk enables/disables can be removed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Use PM runtime and HWMOD support to handle enabling and disabling of DSS
modules.

Each DSS module will have get and put functions which can be used to
enable and disable that module. The functions use pm_runtime and hwmod
opt-clocks to enable the hardware.
Acked-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

CONFIG_OMAP2_DSS_SLEEP_BEFORE_RESET is used to avoid an unclear bug at
DSS reset time. The pm runtime will handle reset in the future, and this
code has to be removed. Hopefully we won't see this error anymore.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Currently dss.c does all the low level clock handling in the DSS, and
thus it contains pointers to all the clocks. This allows dss.c to dump
the clock information for all the clocks.

With pm_runtime this is no longer the case, as each submodule will
handle its clocks independently. Thus remove the core_dump_clocks
function as it cannot be used with pm_runtime.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DSI PLL requires sys_clk to function, and DPI enables sys_clk when it
wants to use DSI PLL. However, DSI PLL code already handles enabling
sys_clk, so DPI's sys_clk code is extra.

Remove the unneeded sys_clk handling from dpi.c.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The function to get device's context loss count has changed from

omap_pm_get_last_off_on_transaction_id() to
omap_pm_get_dev_context_loss_count()

Change name of the function pointer in omapdss.h accordingly, and use
the term "context loss count" instead of "context id" in the code.

Restructure the context loss count functions to handle errors properly,
and ensure that context is always considered lost if an error happens.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DSS enables core clocks for the duration of initialization to avoid
unnecessary context saves and restores.

With PM runtime the clocks cannot be handled in this way, outside the
dss module drivers. Thus we need to remove the optimization.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The initialization order of the DSS modules is important when pm_runtime
support is implemented. Currently RFBI is initialized before DISPC,
which will cause problems with pm_runtime as RFBI uses DISPC.

The same goes for uninitialization order, and dss_uninit needs to be
called last, and dispc_uninit just before that.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Both dss.c and dsi.c had a probe function, which was almost a dummy one,
calling dss_init() and dsi_init().

Remove the init functions by moving the initialization code into probe
functions.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Get and put for dpll4_m4_ck was handled in dss_init/dss_exit. Move the
code to dss_get/put_clocks(), which is a better place to handle it.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The DMA FIFO threshold registers and burst size registers have changed
for OMAP4.  The current code only handles OMAP2/3 case, and so the
values are a bit off for OMAP4.  A summary of the differences between
OMAP2/3 and OMAP4:

Burst size:
OMAP2/3: 4 x 32 bits / 8 x 32 bits / 16 x 32 bits
OMAP4: 2 x 128 bits / 4 x 128 bits / 8 x 128 bits

Threshold size:
OMAP2/3: in bytes (8 bit units)
OMAP4: in 128bit units

This patch fixes the issue by creating two new helper functions in
dss_features: dss_feat_get_buffer_size_unit() and
dss_feat_get_burst_size_unit(). These return (in bytes) the unit size
for threshold registers and unit size for burst size register,
respectively, and are used to calculate correct values.

For the threshold size the usage is straightforward. However, the burst
size register has different multipliers for OMAP2/3 and OMAP4. This
patch solves the problem by defining the multipliers for the burst size
as 2x, 4x and 8x, which fit fine for the OMAP4 burst size definition
(i.e. burst size unit for OMAP4 is 128bits), but requires a slight twist
on OMAP2/3 by defining the burst size unit as 64bit.

As the driver in practice always uses the maximum burst size, and no use
case currently exists where we would want to use a smaller burst size,
this patch changes the driver to hardcode the burst size when
initializing DISPC. This makes the threshold configuration code somewhat
simpler.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

When the panel driver calls omapdss_dsi_display_disable() it is possible
that there are still some unsent packets in the TX fifo.

Add dsi_sync_vc() calls in the beginning of
omapdss_dsi_display_disable() to make sure the TX fifos are empty.

This allows us to remove the msleep(10) hack from panel-taal.c
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add Color Phase Rotation (CPR) support and sysfs files to enable CPR and
to set the CPR coefficient matrix.

CPR is enabled via manager?/cpr_enable file, and the coefficient matrix
is set via manager?/cpr_coef file. The values in cpr_coef are in the
following order:

RR RG RB GR GG GB BR BG BB
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>