This patch (as1583) changes ehci-hcd to use an hrtimer event for
unlinking empty (unused) async QHs instead of using a kernel timer.

The check for empty QHs is moved to a new routine, where it doesn't
require going through an entire scan of both the async and periodic
schedules.  And it can unlink multiple QHs at once, unlike the current
code.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1582) changes ehci-hcd's strategy for unlinking async
QHs.  Currently the driver never unlinks more than one QH at a time.
This can be inefficient and cause unnecessary delays, since a QH
cannot be reused while it is waiting to be unlinked.

The new strategy unlinks all the waiting QHs at once.  In practice the
improvement won't be very big, because it's somewhat uncommon to have
two or more QHs waiting to be unlinked at any time.  But it does
happen, and in any case, doing things this way makes more sense IMO.

The change requires the async unlinking code to be refactored
slightly.  Now in addition to the routines for starting and ending an
unlink, there are new routines for unlinking a single QH and starting
an IAA cycle.  This approach is needed because there are two separate
paths for unlinking async QHs:

	When a transfer error occurs or an URB is cancelled, the QH
	must be unlinked right away;

	When a QH has been idle sufficiently long, it is unlinked
	to avoid consuming DMA bandwidth uselessly.

In the first case we want the unlink to proceed as quickly as
possible, whereas in the second case we can afford to batch several
QHs together and unlink them all at once.  Hence the division of
labor.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1581) replaces the iaa_watchdog kernel timer used by
ehci-hcd with an hrtimer event, in keeping with the general conversion
to high-res timers.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1580) makes ehci_iso_stream structures behave more like
QHs, in that they will remain allocated until their isochronous
endpoint is disabled.  This will come in useful in the future, when
periodic bandwidth gets allocated as an altsetting is installed rather
than on-the-fly.

For now, the change to the ehci_iso_stream lifetimes means that each
structure is always deallocated at exactly one spot in
ehci_endpoint_disable() and never used again.  As a result, it is no
longer necessary to use reference counting on these things, and the
patch removes it.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1579) adds an hrtimer event to handle deallocation of
iTDs and siTDs in ehci-hcd.

Because of the frame-oriented approach used by the EHCI periodic
schedule, the hardware can continue to access the Transfer Descriptor
for isochronous (or split-isochronous) transactions for up to a
millisecond after the transaction completes.  The iTD (or siTD) must
not be reused before then.

The strategy currently used involves putting completed iTDs on a list
of cached entries and every so often returning them to the endpoint's
free list.  The new strategy reduces overhead by putting completed
iTDs back on the free list immediately, although they are not reused
until it is safe to do so.

When the isochronous endpoint stops (its queue becomes empty), the
iTDs on its free list get moved to a global list, from which they will
be deallocated after a minimum of 2 ms.  This delay is what the new
hrtimer event is for.

Overall this may not be a tremendous improvement over the current
code, but to me it seems a lot more clear and logical.  In addition,
it removes the need for each iTD to keep a reference to the
ehci_iso_stream it belongs to, since the iTD never needs to be moved
back to the stream's free list from the global list.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1578) adds an hrtimer event to handle the death of an
EHCI controller.  When a controller dies, it doesn't necessarily stop
running right away.  The new event polls at 1-ms intervals to see when
all activity has safely stopped.  This replaces a busy-wait polling
loop in the current code.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1577) adds hrtimer support for unlinking interrupt QHs
in ehci-hcd.  The current code relies on a fixed delay of either 2 or
55 us, which is not always adequate and in any case is totally bogus.
Thanks to internal caching, the EHCI hardware may continue to access
an interrupt QH for more than a millisecond after it has been unlinked.

In fact, the EHCI spec doesn't say how long to wait before using an
unlinked interrupt QH.  The patch sets the delay to 9 microframes
minimum, which ought to be adequate.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1576) adds hrtimer support for managing ehci-hcd's
async schedule.  Just as with the earlier change to the periodic
schedule management, two new hrtimer events take care of everything.

One event polls at 1-ms intervals to see when the Asynchronous
Schedule Status (ASS) flag matches the Asynchronous Schedule Enable
(ASE) value; the schedule's state must not be changed until it does.
The other event delays for 15 ms after the async schedule becomes
empty before turning it off.

The new events replace a busy-wait poll and a kernel timer usage.
They also replace the rather illogical method currently used for
indicating the async schedule should be turned off: attempting to
unlink the dedicated QH at the head of the async list.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1575) removes special code added for status polling of
the EHCI controller in PS3 systems.  While the controller is running,
the polling is now carried out by an hrtimer handler.  When the
controller is suspending or stopping, we use the same polling routine
as the old code -- but in neither case do we need to conclude that the
controller has died if the polling goes on for too long.

As a result the entire handshake_on_error_set_halt() routine is now
unused, so it is removed from the driver.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1574) changes the return type of multiple functions in
ehci-sched.c from int to void.  The values they return are now always
0, so there's no reason for them to return any value at all.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1573) adds hrtimer support for managing ehci-hcd's
periodic schedule.  There are two issues to deal with.

First, the schedule's state (on or off) must not be changed until the
hardware status has caught up with the current command.  This is
handled by an hrtimer event that polls at 1-ms intervals to see when
the Periodic Schedule Status (PSS) flag matches the Periodic Schedule
Enable (PSE) value.

Second, the schedule should not be turned off as soon as it becomes
empty.  Turning the schedule on and off takes time, so we want to wait
until the schedule has been empty for a suitable period before turning
it off.  This is handled by an hrtimer event that gets set to expire
10 ms after the periodic schedule becomes empty.

The existing code polls (for up to 1125 us and with interrupts
disabled!) to check the status, and doesn't implement a delay before
turning off the schedule.  Furthermore, if the polling fails then the
driver decides that the controller has died.  This has caused problems
for several people; some controllers can take 10 ms or more to turn
off their periodic schedules.

This patch fixes these issues.  It also makes the "broken_periodic"
workaround unnecessary; there is no longer any danger of turning off
the periodic schedule after it has been on for less than 1 ms.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1572) begins the conversion of ehci-hcd over to using
high-resolution timers rather than old-fashioned low-resolution kernel
timers.  This reduces overhead caused by timer roundoff on systems
where HZ is smaller than 1000.  Also, the new timer framework
introduced here is much more logical and easily extended than the
ad-hoc approach ehci-hcd currently uses for timers.

An hrtimer structure is added to ehci_hcd, along with a bitflag array
and an array of ktime_t values, to keep track of which timing events
are pending and what their expiration times are.

Only the infrastructure for the timing operations is added in this
patch.  Later patches will add routines for handling each of the
various timing events the driver needs.  In some cases the new hrtimer
handlers will replace the existing handlers for ehci-hcd's kernel
timers; as this happens the old timers will be removed.  In other
cases the new timing events will replace busy-wait loops.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1571) adds a new state for ehci-hcd's root hubs:
EHCI_RH_STOPPING.  This value is used at times when the root hub is
being stopped and we don't know whether or not the hardware has
finished all its DMA yet.

Although the purpose may not be apparent, this distinction will come
in useful later on.  Future patches will avoid actions that depend on
the root hub being operational (like turning on the async or periodic
schedules) when they see the state is EHCI_RH_STOPPING.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1570) adds a pointer for the end of ehci-hcd's
async-unlink list.  The list (which is actually a queue) is singly
linked, so having a pointer to its end makes adding new entries easier
-- there's no longer any need to scan through the whole list.

In principle it could be changed to a standard doubly-linked list.  It
turns out that doing so actually makes the code less clear, so I'm
leaving it as is.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1569) renames the ehci->reclaim list in ehci-hcd.  The
word "reclaim" is used in the EHCI specification to mean something
quite different, and "unlink_next" is more descriptive of the list's
purpose anyway.

Similarly, the "reclaim" field in the ehci_stats structure is renamed
"iaa", which is more meaningful (to experts, anyway) and is a better
match for the "lost_iaa" field.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1568) introduces symbolic constants for some of the
less-frequently used bitfields in the QH structure.  This makes the
code a little easier to read and understand.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1567) removes ehci-hcd's reference counting of QH
structures.  It's not necessary to refcount these things because they
always get deallocated at exactly one spot in ehci_endpoint_disable()
(except for two special QHs, ehci->async and ehci->dummy) and are
never used again.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1566) removes the code in ehci-hcd's resume routines
which tries to restart or cancel any transfers left active while the
root hub or controller was asleep.  This code isn't necessary, because
all URBs are terminated before the root hub is suspended.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently, EHCI initialization turns off the controller (in case it
was left running by the firmware) before setting up the ehci_hcd data
structure.  This patch (as1565) reverses that order.

Although it doesn't matter now, it will matter later on when future
additions to ehci_halt() will want to acquire a spinlock that gets
initialized by ehci_init().
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Update information of Seagate Portable HDD and WD My Passport HDD in
quirk list.
Signed-off-by: NNamjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: NPankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: NAmit Sahrawat <a.sahrawat@samsung.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for write cache quirk on usb hdd. scsi driver will be set to wce
by detecting write cache quirk in quirk list when plugging usb hdd.
Signed-off-by: NNamjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: NPankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: NAmit Sahrawat <a.sahrawat@samsung.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1564c) converts the EHCI platform drivers to use the
central ehci_setup() routine for generic controller initialization
rather than each having its own idiosyncratic approach.

The major point of difficulty lies in ehci-pci's many vendor- and
device-specific workarounds.  Some of them have to be applied before
calling ehci_setup() and some after, which necessitates a fair amount
of code motion.  The other platform drivers require much smaller
changes.

One point not addressed by the patch is whether ports should be
powered on or off following initialization.  The different drivers
appear to handle this pretty much at random.  In fact it shouldn't
matter, because the hub driver turns on power to all ports when it
binds to the root hub.  Straightening that out will be left for
another day.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch supports only the host-mode functionality so far.
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Tested-by: NSubodh Nijsure <snijsure@grid-net.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

mxs phy is used in Freescale i.MX SoCs, for example
imx23, imx28, imx6Q. This patch adds the basic host
support.
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Peter Chen <peter.chen@freescale.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NSubodh Nijsure <snijsure@grid-net.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Sometimes, the driver bindings may know what phy they use.
For example, when using device tree, the usb controller may have a
phandler pointing to usb phy.
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Acked-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NSubodh Nijsure <snijsure@grid-net.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

ci13xxx host needs Root Hub Transaction Translators.
Reported-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We use ida_simple_get and ida_simple_remove to manage the ids.
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Platform drivers do the similar things to add/remove ci13xxx device, so
create a unified one.
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

struct ci13xxx represent the controller, which may be device or host,
so name its variables as ci.
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch used dmaengine helper functions instead of using hand setting.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed a mistake in the merge conflict resoultion commit(ff9cce) in file
twl6030-usb.c
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We don't support sg for isoc transfers, enforce this.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1563) removes a lot of duplicated code by moving the
EHCI controller suspend/resume routines into the core driver, where
the various platform drivers can invoke them as needed.

Not only does this simplify these platform drivers, this also makes it
easier for other platform drivers to add suspend/resume support in the
future.

Note: The patch does not touch the ehci-fsl.c file, because its
approach to suspend and resume is so different from all the others.
It will have to be handled specially by its maintainer.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' (1fcb57d0) fixes
an issue where the ULPI PHYs were not held in reset while initializing
the EHCI controller. However, it also changes behavior in
omap-usb-host.c omap_usbhs_init by releasing reset while the
configuration in that function was done.

This change caused a regression on BB-xM where USB would not function
if 'usb start' had been run from u-boot before booting. A change was
made to release reset a little bit earlier which fixed the issue on
BB-xM and did not cause any regressions on 3430 sdp, the board for
which the fix was originally made.

This new fix, 'USB: EHCI: OMAP: Finish ehci omap phy reset cycle
before adding hcd.', (3aa2ae74) caused a regression on OMAP5.

The original fix to hold the EHCI controller in reset during
initialization was correct, however it appears that changing
omap_usbhs_init to not hold the PHYs in reset during it's
configuration was incorrect. This patch first reverts both fixes, and
then changes ehci_hcd_omap_probe in ehci-omap.c to hold the PHYs in
reset as the original patch had done. It also is sure to incorporate
the _cansleep change that has been made in the meantime.

I've tested this on Beagleboard xM, I'd really like to get an ack from
the 3430 sdp and OMAP5 guys before getting this merged.

v3 - Brown paper bag its too early in the morning actually run
     git commit amend fix
v2 - Put cansleep gpiolib call outside of spinlock
Acked-by: NMantesh Sarashetti <mantesh@ti.com>
Tested-by: NMantesh Sarashetti <mantesh@ti.com>
Acked-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Tested-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NRuss Dill <Russ.Dill@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch is to convert port_owners type from void * to struct dev_state *
in order to make code more readable.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch rename struct ci13xxx_udc_driver and var with the type.

ci13xxx_platform_data reflect it's passed from platfrom driver.
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

allow this driver to be removed too.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

No functional changes, it will just free up some
code if we don't have hotplug.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

msm glue layer compiles on all arches just
fine. Let's drop the unnecessary ARCH check
so we have easier compile tests.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

As reported by Dan Carpenter, there is a NULL check in udc_start() that
follows a dereference of the pointer that's being checked. However, at
that point udc pointer shouldn't ever be NULL and if it is, the dereference
should cause an oops.
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>