This patch (as1583) changes ehci-hcd to use an hrtimer event for
unlinking empty (unused) async QHs instead of using a kernel timer.

The check for empty QHs is moved to a new routine, where it doesn't
require going through an entire scan of both the async and periodic
schedules.  And it can unlink multiple QHs at once, unlike the current
code.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1582) changes ehci-hcd's strategy for unlinking async
QHs.  Currently the driver never unlinks more than one QH at a time.
This can be inefficient and cause unnecessary delays, since a QH
cannot be reused while it is waiting to be unlinked.

The new strategy unlinks all the waiting QHs at once.  In practice the
improvement won't be very big, because it's somewhat uncommon to have
two or more QHs waiting to be unlinked at any time.  But it does
happen, and in any case, doing things this way makes more sense IMO.

The change requires the async unlinking code to be refactored
slightly.  Now in addition to the routines for starting and ending an
unlink, there are new routines for unlinking a single QH and starting
an IAA cycle.  This approach is needed because there are two separate
paths for unlinking async QHs:

	When a transfer error occurs or an URB is cancelled, the QH
	must be unlinked right away;

	When a QH has been idle sufficiently long, it is unlinked
	to avoid consuming DMA bandwidth uselessly.

In the first case we want the unlink to proceed as quickly as
possible, whereas in the second case we can afford to batch several
QHs together and unlink them all at once.  Hence the division of
labor.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1581) replaces the iaa_watchdog kernel timer used by
ehci-hcd with an hrtimer event, in keeping with the general conversion
to high-res timers.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1580) makes ehci_iso_stream structures behave more like
QHs, in that they will remain allocated until their isochronous
endpoint is disabled.  This will come in useful in the future, when
periodic bandwidth gets allocated as an altsetting is installed rather
than on-the-fly.

For now, the change to the ehci_iso_stream lifetimes means that each
structure is always deallocated at exactly one spot in
ehci_endpoint_disable() and never used again.  As a result, it is no
longer necessary to use reference counting on these things, and the
patch removes it.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1579) adds an hrtimer event to handle deallocation of
iTDs and siTDs in ehci-hcd.

Because of the frame-oriented approach used by the EHCI periodic
schedule, the hardware can continue to access the Transfer Descriptor
for isochronous (or split-isochronous) transactions for up to a
millisecond after the transaction completes.  The iTD (or siTD) must
not be reused before then.

The strategy currently used involves putting completed iTDs on a list
of cached entries and every so often returning them to the endpoint's
free list.  The new strategy reduces overhead by putting completed
iTDs back on the free list immediately, although they are not reused
until it is safe to do so.

When the isochronous endpoint stops (its queue becomes empty), the
iTDs on its free list get moved to a global list, from which they will
be deallocated after a minimum of 2 ms.  This delay is what the new
hrtimer event is for.

Overall this may not be a tremendous improvement over the current
code, but to me it seems a lot more clear and logical.  In addition,
it removes the need for each iTD to keep a reference to the
ehci_iso_stream it belongs to, since the iTD never needs to be moved
back to the stream's free list from the global list.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1578) adds an hrtimer event to handle the death of an
EHCI controller.  When a controller dies, it doesn't necessarily stop
running right away.  The new event polls at 1-ms intervals to see when
all activity has safely stopped.  This replaces a busy-wait polling
loop in the current code.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1577) adds hrtimer support for unlinking interrupt QHs
in ehci-hcd.  The current code relies on a fixed delay of either 2 or
55 us, which is not always adequate and in any case is totally bogus.
Thanks to internal caching, the EHCI hardware may continue to access
an interrupt QH for more than a millisecond after it has been unlinked.

In fact, the EHCI spec doesn't say how long to wait before using an
unlinked interrupt QH.  The patch sets the delay to 9 microframes
minimum, which ought to be adequate.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1576) adds hrtimer support for managing ehci-hcd's
async schedule.  Just as with the earlier change to the periodic
schedule management, two new hrtimer events take care of everything.

One event polls at 1-ms intervals to see when the Asynchronous
Schedule Status (ASS) flag matches the Asynchronous Schedule Enable
(ASE) value; the schedule's state must not be changed until it does.
The other event delays for 15 ms after the async schedule becomes
empty before turning it off.

The new events replace a busy-wait poll and a kernel timer usage.
They also replace the rather illogical method currently used for
indicating the async schedule should be turned off: attempting to
unlink the dedicated QH at the head of the async list.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1575) removes special code added for status polling of
the EHCI controller in PS3 systems.  While the controller is running,
the polling is now carried out by an hrtimer handler.  When the
controller is suspending or stopping, we use the same polling routine
as the old code -- but in neither case do we need to conclude that the
controller has died if the polling goes on for too long.

As a result the entire handshake_on_error_set_halt() routine is now
unused, so it is removed from the driver.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1574) changes the return type of multiple functions in
ehci-sched.c from int to void.  The values they return are now always
0, so there's no reason for them to return any value at all.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1573) adds hrtimer support for managing ehci-hcd's
periodic schedule.  There are two issues to deal with.

First, the schedule's state (on or off) must not be changed until the
hardware status has caught up with the current command.  This is
handled by an hrtimer event that polls at 1-ms intervals to see when
the Periodic Schedule Status (PSS) flag matches the Periodic Schedule
Enable (PSE) value.

Second, the schedule should not be turned off as soon as it becomes
empty.  Turning the schedule on and off takes time, so we want to wait
until the schedule has been empty for a suitable period before turning
it off.  This is handled by an hrtimer event that gets set to expire
10 ms after the periodic schedule becomes empty.

The existing code polls (for up to 1125 us and with interrupts
disabled!) to check the status, and doesn't implement a delay before
turning off the schedule.  Furthermore, if the polling fails then the
driver decides that the controller has died.  This has caused problems
for several people; some controllers can take 10 ms or more to turn
off their periodic schedules.

This patch fixes these issues.  It also makes the "broken_periodic"
workaround unnecessary; there is no longer any danger of turning off
the periodic schedule after it has been on for less than 1 ms.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1572) begins the conversion of ehci-hcd over to using
high-resolution timers rather than old-fashioned low-resolution kernel
timers.  This reduces overhead caused by timer roundoff on systems
where HZ is smaller than 1000.  Also, the new timer framework
introduced here is much more logical and easily extended than the
ad-hoc approach ehci-hcd currently uses for timers.

An hrtimer structure is added to ehci_hcd, along with a bitflag array
and an array of ktime_t values, to keep track of which timing events
are pending and what their expiration times are.

Only the infrastructure for the timing operations is added in this
patch.  Later patches will add routines for handling each of the
various timing events the driver needs.  In some cases the new hrtimer
handlers will replace the existing handlers for ehci-hcd's kernel
timers; as this happens the old timers will be removed.  In other
cases the new timing events will replace busy-wait loops.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1571) adds a new state for ehci-hcd's root hubs:
EHCI_RH_STOPPING.  This value is used at times when the root hub is
being stopped and we don't know whether or not the hardware has
finished all its DMA yet.

Although the purpose may not be apparent, this distinction will come
in useful later on.  Future patches will avoid actions that depend on
the root hub being operational (like turning on the async or periodic
schedules) when they see the state is EHCI_RH_STOPPING.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1570) adds a pointer for the end of ehci-hcd's
async-unlink list.  The list (which is actually a queue) is singly
linked, so having a pointer to its end makes adding new entries easier
-- there's no longer any need to scan through the whole list.

In principle it could be changed to a standard doubly-linked list.  It
turns out that doing so actually makes the code less clear, so I'm
leaving it as is.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1569) renames the ehci->reclaim list in ehci-hcd.  The
word "reclaim" is used in the EHCI specification to mean something
quite different, and "unlink_next" is more descriptive of the list's
purpose anyway.

Similarly, the "reclaim" field in the ehci_stats structure is renamed
"iaa", which is more meaningful (to experts, anyway) and is a better
match for the "lost_iaa" field.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1568) introduces symbolic constants for some of the
less-frequently used bitfields in the QH structure.  This makes the
code a little easier to read and understand.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1567) removes ehci-hcd's reference counting of QH
structures.  It's not necessary to refcount these things because they
always get deallocated at exactly one spot in ehci_endpoint_disable()
(except for two special QHs, ehci->async and ehci->dummy) and are
never used again.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1566) removes the code in ehci-hcd's resume routines
which tries to restart or cancel any transfers left active while the
root hub or controller was asleep.  This code isn't necessary, because
all URBs are terminated before the root hub is suspended.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently, EHCI initialization turns off the controller (in case it
was left running by the firmware) before setting up the ehci_hcd data
structure.  This patch (as1565) reverses that order.

Although it doesn't matter now, it will matter later on when future
additions to ehci_halt() will want to acquire a spinlock that gets
initialized by ehci_init().
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Update information of Seagate Portable HDD and WD My Passport HDD in
quirk list.
Signed-off-by: NNamjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: NPankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: NAmit Sahrawat <a.sahrawat@samsung.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for write cache quirk on usb hdd. scsi driver will be set to wce
by detecting write cache quirk in quirk list when plugging usb hdd.
Signed-off-by: NNamjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: NPankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: NAmit Sahrawat <a.sahrawat@samsung.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make use of USB quirk method to identify such HDD while reading
the cache status in sd_probe(). If cache quirk is present for
the HDD, lets assume that cache is enabled and make WCE bit
equal to 1.
Signed-off-by: NNamjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: NPankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: NAmit Sahrawat <a.sahrawat@samsung.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The idr_pre_get() function never returns a value < 0.  It returns 0 (no
memory) or 1 (OK).
Reported-by: NSilva Paulo <psdasilva@yahoo.com>
[ Rewrote Silva's patch, but attributing it to Silva anyway  - Linus ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixes a problem that can occur when a lone package object is
wrapped with an outer package object in order to conform to
the ACPI specification. Can affect these predefined names:
_ALR,_MLS,_PSS,_TRT,_TSS,_PRT,_HPX,_DLM,_CSD,_PSD,_TSD

https://bugzilla.kernel.org/show_bug.cgi?id=44171

This problem was introduced in 3.4-rc1 by commit
6a99b1c9
(ACPICA: Object repair code: Support to add Package wrappers)
Reported-by: NVlastimil Babka <caster@gentoo.org>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Cc: <stable@vger.kernel.org> # 3.4
Signed-off-by: NLen Brown <len.brown@intel.com>

I couldn't find the vendor ID in any of the online databases, but this
mat has a Pump It Up logo on the top side of the controller compartment,
and a disclaimer stating that Andamiro will not be liable on the bottom.
Signed-off-by: NYuri Khan <yurivkhan@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

We were accidentally losing one bit in the configuration register on
device initialization. It was reported to freeze one specific system
right away. Properly preserve all bits we don't explicitly want to
change in order to prevent that.
Reported-by: NStevie Trujillo <stevie.trujillo@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>

Commit d640113f introduced a regression on SMP
systems where the processor core with ACPI id zero is disabled
(typically should be the case because of hyperthreading).
The regression got spread through stable kernels.
On 3.0.X it got introduced via 3.0.18.

Such platforms may be rare, but do exist.
Look out for a disabled processor with acpi_id 0 in dmesg:
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x10] disabled)

This problem has been observed on a:
HP Proliant BL280c G6 blade

This patch restricts the introduced workaround to platforms
with nr_cpu_ids <= 1.
Signed-off-by: NThomas Renninger <trenn@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Requesting a threaded interrupt without a primary handler and without
IRQF_ONESHOT is dangerous, and after commit 1c6c6952 ("genirq: Reject
bogus threaded irq requests"), these requests are rejected.  This causes
->probe() to fail, and the RTC driver not to be availble.

To fix, add IRQF_ONESHOT to the IRQ flags.

Tested on OMAP3730/OveroSTORM and OMAP4430/Panda board using rtcwake to
wake from system suspend multiple times.
Signed-off-by: NKevin Hilman <khilman@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The code here has a nested spin_lock_irqsave().  It's not needed since
IRQs are already disabled and it causes a problem because it means that
IRQs won't be enabled again at the end.  The second call to
spin_lock_irqsave() will overwrite the value of irq_flags and we can't
restore the proper settings.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NRobin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixes

  WARNING: at irq/handle.c:146 handle_irq_event_percpu+0x19c/0x1b8()
  irq 25 handler mxc_rtc_interrupt+0x0/0xac enabled interrupts
  Modules linked in:
   (unwind_backtrace+0x0/0xf0) from (warn_slowpath_common+0x4c/0x64)
   (warn_slowpath_common+0x4c/0x64) from (warn_slowpath_fmt+0x30/0x40)
   (warn_slowpath_fmt+0x30/0x40) from (handle_irq_event_percpu+0x19c/0x1b8)
   (handle_irq_event_percpu+0x19c/0x1b8) from (handle_irq_event+0x28/0x38)
   (handle_irq_event+0x28/0x38) from (handle_level_irq+0x80/0xc4)
   (handle_level_irq+0x80/0xc4) from (generic_handle_irq+0x24/0x38)
   (generic_handle_irq+0x24/0x38) from (handle_IRQ+0x30/0x84)
   (handle_IRQ+0x30/0x84) from (avic_handle_irq+0x2c/0x4c)
   (avic_handle_irq+0x2c/0x4c) from (__irq_svc+0x40/0x60)
  Exception stack(0xc050bf60 to 0xc050bfa8)
  bf60: 00000001 00000000 003c4208 c0018e20 c050a000 c050a000 c054a4c8 c050a000
  bf80: c05157a8 4117b363 80503bb4 00000000 01000000 c050bfa8 c0018e2c c000e808
  bfa0: 60000013 ffffffff
   (__irq_svc+0x40/0x60) from (default_idle+0x1c/0x30)
   (default_idle+0x1c/0x30) from (cpu_idle+0x68/0xa8)
   (cpu_idle+0x68/0xa8) from (start_kernel+0x22c/0x26c)
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Sascha Hauer <kernel@pengutronix.de>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Without this patch, if Device Tree is enabled the AB8500 RTC wouldn't get
probed at all, as there is no reference to it from platform code.  This
patch ensures the driver is probed during normal DT start-up.

[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This driver's IRQ registration is failing because the kernel now forces
IRQs to be ONESHOT if no IRQ handler is passed.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

`config' is freed and is then used in the rtc_device_unregister() call,
causing a kernel panic.
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Reviewed-by: NViresh Kumar <viresh.linux@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Do not use MX2_CAMERA_SWAP16 and MX2_CAMERA_PACK_DIR_MSB flags. The driver
must negotiate with the attached sensor whether the mbus format is UYUV or
YUYV and set CSICR1 configuration accordingly.

This is needed for the video function on mach-imx27_visstrim_m10.c to
perform properly, since an earlier version of this patch has been proven
wrong and has been reverted and a commit, depending on it: "[media]
i.MX27: visstrim_m10: Remove use of MX2_CAMERA_SWAP16" is in the mainline.
Signed-off-by: NJavier Martin <javier.martin@vista-silicon.com>
Reviewed-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
[ g.liakhovetski@gmx.de: move a macro definition to a more logical place ]
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
[ Applying directly because Mauro is on vacation - Linus ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NIlia Katsnelson <k0009000@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The device should be handled by xpad driver instead of generic HID driver.
Signed-off-by: NYuri Khan <yurivkhan@gmail.com>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Fix a boot regression on Mackerel boards with sh_mobile_sdhi
in existing kernels causing:

genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq XXX

caused by 1c6c6952 (genirq: Reject bogus threaded irq requests).

This is backported from Guennadi's patch:
"mmc: extend and rename cd-gpio helpers to handle more slot GPIO functions"
Reported-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

This reverts commit 3d93576e(skip card initialization if
power class selection fails).
Problem has been reported when this is used with eMMC4.41
card with Tegra Platform. Till the issue is root caused,
bus width selection failure should not be treated as fatal.
Reported-by: NMarc Dietrich <marvin24@gmx.de>
Signed-Off-by: NVenkatraman S <svenkatr@ti.com>
CC: Ulf Hansson <ulf.hansson@stericsson.com>
CC: Subhash Jadavani <subhashj@codeaurora.org>
CC: Saugata Das <saugata.das@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

commit 626f9914 added code to initialize gpio_chip.of_node, but if
CONFIG_OF_GPIO is not defined gps-tps65910 fails to build with an
error complaining gpio_chip has no member of_node. I ran into this
while doing a allyesconfig build on linux-next.
Signed-off-by: NGerard Snitselaar <dev@snitselaar.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This is an old suspend/resume lockup fix:

	commit 2780cc4660e1
	Author: Len Brown <len.brown@intel.com>
	Date:   Thu Dec 23 13:43:30 2004 -0500

	    [ACPI] Fix suspend/resume lockup issue
	    by leaving Bus Master Arbitration enabled.
	    The ACPI spec mandates it be disabled only for C3.

	    http://bugzilla.kernel.org/show_bug.cgi?id=3599Signed-off-by: NDavid Shaohua Li <shaohua.li@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

The bug snuck back in in commit 2feec47d (ACPICA: ACPI 5: Support
for new FADT SleepStatus, SleepControl registers, 2012-02-14),
presumably by copy/pasting a copy of the code without that fix for the
legacy case.

On affected machines, after that commit, the machine locks up hard on
resume from suspend.  The same fix as seven years ago still works.

Addresses <https://bugzilla.kernel.org/show_bug.cgi?id=43641>.
Reported-bisected-and-tested-by: NOctavio Alvarez <alvarezp@alvarezp.com>
Reported-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NJonathan Nieder <jrnieder@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>