- 08 10月, 2010 4 次提交
-
-
由 James Smart 提交于
Replace graceful teardown steps with the singular function reset command. Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
- Added driver support for management application to pass down two security specific mailbox commands (MBX_SECURITY_MGMT and MBX_AUTH_PORT) - Added driver support for handling FIPS zeroization trap of host ERATT ER8, performing selective reset and bringing the device up. - Added code to detect INIT_LINK mailbox command completion returning status MBXERR_SEC_NO_PERMISSION. - Increased the wait timeout on host status register HS_FFRDY and HS_MBRDY being set. - Remove the port offline code from the Heartbeat TMO handler. Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
- Move Unload flag earlier in vport deletei to stop ELS traffic - Replaced some unnecessary spin_lock_irqsave with spin_lock_irq - Fixed circular spinlock dependency between low-level driver and SCSI midlayer - Remove duplicate code from lpfc_els_retry routine - Make all error values negative Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 Mike Christie 提交于
This removes the driver's get_host_def_dev_loss_tmo callback and just has the driver set the dev loss using the fc class fc_host_dev_loss_tmo macro like is done for other fc params. It also adds compat support for the driver's existing dev loss and nodev sysfs and modparams. Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
- 07 8月, 2010 2 次提交
-
-
由 James Smart 提交于
- Add support for re-reg'ing changed VPI w/o unregister VPI - Copy WWN and state from old nodelist when target DID change. - Clean up old nodelist rport and put the nodelist when target DID change. - Clear the VFI_REGISTERED flag when UNREG_VFI completes. - Made both checks of port_state against LPFC_FLOGI and LPFC_FDISC non-inclusive for ignoring CVL events. - Added logic to stop retrying of the ongoing PLOGI and FDISC if transitioned back to the FCF rediscovery state in reaction to CVL. - Removed the dependency of scanning of all the available FCF table entries for bulding round-robin bitmap. - Use the lpfc_sli4_fcf_rr_read_fcf_rec() in responding to individual New FCF found event. Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
- Remove unneeded Endian swap for Block Guard IOCB response - Add a check for mailbox active before issuing the heartbeat command - Correct heartbeat last_completion updates to avoid unneeded heartbeats - Add Security crypto support to CONFIG_PORT mailbox command - Add fips level and fips spec revision sysfs parameters - Remove duplicate setting of ext_byte_len fields in lpfc_bsg_issue_mbox - Switch call to memcpy_toio to __write32_copy to prevent unaligned 64 bit copy - Change log message 0318 from an error to a warning as it is not an error - Patch an incorrect call to lpfc_drain_txq on SLI-3 functions Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
- 28 7月, 2010 7 次提交
-
-
由 James Smart 提交于
FCoE Related Fixes - Correct find-next-FCF routine so that it searches at next FCF rather than current one. - Enhanced round-robin FCF failover algorithm to re-start on "New FCF" async event - Update the manner in which we look at FCFs while they may be in their discovery state. - Use LPFC_FCOE_NULL_VID macro when checkinf for valid vlan_id for FCF Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
- Fixed accounting of allocated SCSI buffers when post sgl fails. - Restrict scsi buffer allocation based on LUN count (sdev_cnt). - Create __lpfc_sli_free_rpi that doesn't take out the hbalock. - Modify lpfc_sli_free_rpi to call __lpfc_sli_free_rpi. - Call __lpfc_sli_free_rpi in lpfc_cleanup_pending_mbox. - Do not swap the strings returned in mailbox commands and do not swap byte aligned data in VPD. Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
- Allow enabling MSI-X intterupts with fewer vectors than requested by looking at the return value from pci_enable_msix. - Implemented driver PCI AER error handling routines for supporting AER error recovering on SLI4 devices. - Remove redundant SLI_ACTIVE checks Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
- Change the Max receive size on CIN FCFs to 0x800 - (From linux community) Check boundary before checking for NULL. - Update last completion time for completed I/O to prevent heartbeat. - Add Balius PCI Device IDs Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
- Fix hba_queue_depth to reflect actual available XRIs - Add support for new SLER specific firmware status codes. - Free SCSI buffer when iotag allocation fails. Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
- Add poll or wait flag parameter to hba_init_link and hba_down_link. - (From Linux Community) Make return with ENXIO negative. - Remove unused INB code from driver. - Prevent block_magmt_io from returning until mailbox is inactive. Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
- 12 4月, 2010 3 次提交
-
-
由 James Smart 提交于
- Add code to prevent unreg_vpi mailbox command from failing. - Add code to reset the HBA if unreg_vpi mailbox fails with busy status. - Remove code that was clearing the nlp_type stored during rport discovery. Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
- Move the code to increase the sg seg count for LP21000 adapters. - Check pcmd on command completion before dereferencing it. - Clear queue memory when creating firmware queues to prevent stale entries. - Replace the use of PAGE_SIZE in many areas that assumed it was always 4k. - Add an else clause to a conditional that needed to unlock the hba_lock. Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
- Add the new Logical Link speed event support. - Add RATOV and EDTOV to the REG_VFI mailbox command. Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
- 11 4月, 2010 4 次提交
-
-
由 James Smart 提交于
Only abort outstanding I/O to force the OS to retry failed I/Os for AER uncorrectable non-fatal errors instead of reseting the adapter. Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
- Add BSG support for PCI loopback testing. - Add BSG support for extended mailbox commands. Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
- Correct all SLI4 code to work on big endian systems. - Move read of sli4 params earlier so returned values are used correctly. Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
FCF failover improvements - Add random FCF failover when there are multiple FCFs available. - Prevent FCF log messages from being displayed for FC adapters. - Separate the New FCF and Modified FCF log messages. Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
- 30 3月, 2010 1 次提交
-
-
由 Tejun Heo 提交于
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: NTejun Heo <tj@kernel.org> Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
-
- 03 3月, 2010 6 次提交
-
-
由 James Smart 提交于
- Added round robin FCF failover on initial or FCF rediscovery FLOGI failure. Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
- Prevent Vport discovery after reg_new_vport completes when physical logged in using FDISC. - Remove fast FCF failover fabric name matching. Allow failover to FCFs connected to different fabrics. - Added fast FCF failover in response to FCF DEAD event on current FCF record. Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
- Clear LPFC_DRIVER_ABORTED on FCP command completion. - Clear exchange busy flag when I/O is aborted and found on aborted list. - Free sglq when XRI_ABORTED event is processed before release of IOCB. - Only process iocb as aborted when LPFC_DRIVER_ABORTED is set. Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
- Add Logging message for critial errors. - Remove unused variable from lpfc_nodev_tmo_show - Update supress_link_up parameter with #define values. Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
- Add NULL checks to the pointers for the config_async mailbox and dump_wakeup_params mailbox. - Add code to check return value of lpfc_read_sparams everywhere and handle failures appropriately. Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
- 18 2月, 2010 5 次提交
-
-
由 James Smart 提交于
- Use the hbalock when changing the fc_flag. - Use the host_lock when changeing the sli_flag. - Prevent NULL pointer dereference after dma_alloc_coherent failure. Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
- Convert all sysfs parameters to uint instead of int. - Add lpfc_supress_link_up parameter. - Change link_state to writable sysfs parameter. - Add support to be able to "up" or "down" link from link_state parameter. Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
- Add support for the INTF (Interface) PCI register. - Add support for greater than 2 page SGLs. - Add support for up to 32 bit BDE lengths. - Implement the Port Capabilities Mailbox command. - Stop checking the Minor Code in the EQE structure. Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
- Add init_vpi mailbox command before re-registering VPI. - Add Fast FCF failover support. Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
- Call pci_save_state() after pci_restore_state() call to cope with kernel change. - Add support for PCI BAR region 0 if BAR0 is a 64 bit register. Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
- 09 2月, 2010 3 次提交
-
-
由 James Smart 提交于
Update BSG infrastructure to handle new vendor specific BSG commands. Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
Display Logical Link Speed when supported and is non-zero. Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
Discovery relates changes: - Separated VPI_REGISTERED state of physical port into VFI_REGISTERED and VPI_REGISTERED state so that driver can unregister physical port VPI independent of VFI. - Add code to unregister, re-init and re-register physical port VPI when physical port NportID change. - Add code to unregister and re-register VPI of a vport when its Nport ID change. - Add code in FDISC completion path to re-start FLOGI discovery when a FDISC complete with LOGIN_REQUIRED reason code. - Fix a memory leak in lpfc_init_vpi_cmpl - Add code to start a timer for vport to retry FDISC when CVL is received by a vport or physical port. If all Nports receive CVLs, then all timers are cancelled and a logical link level discovery will be started after one second. - Flush ELS commands after killing all delayed ELS commands. Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
- 05 1月, 2010 3 次提交
-
-
由 James Smart 提交于
Fix discovery failures: - Move all accesses to the fc_flag field inside the host lock. - Restore link state after going through linkdown processing for FCF DEAD event. Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
Fix SCSI protocol related errors: - Avoid I/O failures during EEH and HBA/CNA reset by correcting when we block the targets on the adapter. Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 James Smart 提交于
Fix hardware/SLI relates issues: - Fix CNA uses more than one EQ when in INTx interrupt mode. - Fix driver tries to process failed read FCF record mailbox request. - Fix allocating single receive buffer breaks FCoE receive queue. - Support new read FCF record mailbox error case. Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
- 10 12月, 2009 1 次提交
-
-
由 Michael Reed 提交于
In testing 2.6.31 on one of our ia64 platforms I've encountered a hang due to the driver using hardware ATEs which are a limited resource. This is because the driver does not set the dma consistent mask to 64 bits. Signed-off-by: NMichael Reed <mdr@sgi.com> Acked-by: NJames Smart <James.Smart@Emulex.Com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
- 05 12月, 2009 1 次提交
-
-
由 James Smart 提交于
Hardware related Fixes and Changes. - Added new Adapter IDs and update default Adapter names. - Added PCI read after EQarm doorbell PCI write to flush the write and avoid spurrious interrupts when in INTx mode. - Phase out use of ONLINE registers. - Fix for lost MSI interrupt Signed-off-by: NJames Smart <james.smart@emulex.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-