- 28 2月, 2018 1 次提交
-
-
由 Vignesh R 提交于
Currently, data in RX FIFO is read based on UART_LSR register state even if RDI and RLSI interrupts are disabled in UART_IER register. This is because when IRQ handler is called due to TX FIFO empty event, RX FIFO is serviced based on UART_LSR register status instead of UART_IIR status. This defeats the purpose of disabling UART RX FIFO interrupts during throttling(see, omap_8250_throttle()) as IRQ handler continues to drain UART RX FIFO resulting in overflow of buffer at tty layer. Fix this by making sure that driver drains UART RX FIFO only when UART_IIR_RDI is set along with UART_LSR_BI or UART_LSR_DR bits. Signed-off-by: NVignesh R <vigneshr@ti.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 25 1月, 2018 1 次提交
-
-
由 Aaron Sierra 提交于
Exar sleep wake-up handling has been done on a per-channel basis by virtue of INT0 being accessible from each channel's address space. I believe this was initially done out of necessity, but now that Exar devices have their own driver, we can do things more efficiently by registering a dedicated INT0 handler at the PCI device level. I see this change providing the following benefits: 1. If more than one port is active, eliminates the redundant bus cycles for reading INT0 on every interrupt. 2. This note associated with hooking in the per-channel handler in 8250_port.c is resolved: /* Fixme: probably not the best place for this */ Cc: Matt Schulte <matts@commtech-fastcom.com> Signed-off-by: NAaron Sierra <asierra@xes-inc.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 08 11月, 2017 2 次提交
-
-
由 Greg Kroah-Hartman 提交于
Now that the SPDX tag is in all tty files, that identifies the license in a specific and legally-defined manner. So the extra GPL text wording can be removed as it is no longer needed at all. This is done on a quest to remove the 700+ different ways that files in the kernel describe the GPL license text. And there's unneeded stuff like the address (sometimes incorrect) for the FSF which is never needed. No copyright headers or other non-license-description text was removed. Cc: Jiri Slaby <jslaby@suse.com> Cc: Eric Anholt <eric@anholt.net> Cc: Stefan Wahren <stefan.wahren@i2se.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Ray Jui <rjui@broadcom.com> Cc: Scott Branden <sbranden@broadcom.com> Cc: bcm-kernel-feedback-list@broadcom.com Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> Cc: Helge Deller <deller@gmx.de> Cc: Joachim Eastwood <manabian@gmail.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Tobias Klauser <tklauser@distanz.ch> Cc: Russell King <linux@armlinux.org.uk> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Richard Genoud <richard.genoud@gmail.com> Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Pat Gefre <pfg@sgi.com> Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Sylvain Lemieux <slemieux.tyco@gmail.com> Cc: Carlo Caione <carlo@caione.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Liviu Dudau <liviu.dudau@arm.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Andy Gross <andy.gross@linaro.org> Cc: David Brown <david.brown@linaro.org> Cc: "Andreas Färber" <afaerber@suse.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: Barry Song <baohua@kernel.org> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Timur Tabi <timur@tabi.org> Cc: Tony Prisk <linux@prisktech.co.nz> Cc: Michal Simek <michal.simek@xilinx.com> Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Greg Kroah-Hartman 提交于
It's good to have SPDX identifiers in all files to make it easier to audit the kernel tree for correct licenses. Update the drivers/tty files files with the correct SPDX license identifier based on the license text in the file itself. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This work is based on a script and data from Thomas Gleixner, Philippe Ombredanne, and Kate Stewart. Cc: Jiri Slaby <jslaby@suse.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: Jiri Kosina <jikos@kernel.org> Cc: David Sterba <dsterba@suse.com> Cc: James Hogan <jhogan@kernel.org> Cc: Rob Herring <robh@kernel.org> Cc: Eric Anholt <eric@anholt.net> Cc: Stefan Wahren <stefan.wahren@i2se.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Ray Jui <rjui@broadcom.com> Cc: Scott Branden <sbranden@broadcom.com> Cc: bcm-kernel-feedback-list@broadcom.com Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> Cc: Helge Deller <deller@gmx.de> Cc: Joachim Eastwood <manabian@gmail.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Tobias Klauser <tklauser@distanz.ch> Cc: Russell King <linux@armlinux.org.uk> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Richard Genoud <richard.genoud@gmail.com> Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Baruch Siach <baruch@tkos.co.il> Cc: "Maciej W. Rozycki" <macro@linux-mips.org> Cc: "Uwe Kleine-König" <kernel@pengutronix.de> Cc: Pat Gefre <pfg@sgi.com> Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Sylvain Lemieux <slemieux.tyco@gmail.com> Cc: Carlo Caione <carlo@caione.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Liviu Dudau <liviu.dudau@arm.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Andy Gross <andy.gross@linaro.org> Cc: David Brown <david.brown@linaro.org> Cc: "Andreas Färber" <afaerber@suse.de> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: Barry Song <baohua@kernel.org> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Timur Tabi <timur@tabi.org> Cc: Tony Prisk <linux@prisktech.co.nz> Cc: Michal Simek <michal.simek@xilinx.com> Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Jiri Slaby <jslaby@suse.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 04 11月, 2017 1 次提交
-
-
由 Tomas Melin 提交于
Canceling hrtimer when holding uart spinlock can deadlock. CPU0: syscall write -> get uart port spinlock -> write uart -> start_tx_rs485 -> hrtimer_cancel -> wait for hrtimer callback to finish CPU1: hrtimer IRQ -> run hrtimer -> em485_handle_stop_tx -> get uart port spinlock CPU0 is waiting for the hrtimer callback to finish, but the hrtimer callback running on CPU1 is waiting to get the uart port spinlock. This deadlock can be avoided by not canceling the hrtimers in these paths. Setting active_timer=NULL can be done without accessing hrtimer, and that will effectively cancel operations that would otherwise have been performed by the hrtimer callback. Signed-off-by: NTomas Melin <tomas.melin@vaisala.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 20 10月, 2017 1 次提交
-
-
由 Aaron Sierra 提交于
The upper four bits of the XR17V35x fractional divisor register (DLD) control general chip function (RS-485 direction pin polarity, multidrop mode, XON/XOFF parity check, and fast IR mode). Don't allow these bits to be clobbered when setting the baudrate. Signed-off-by: NAaron Sierra <asierra@xes-inc.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 04 10月, 2017 1 次提交
-
-
由 Ed Blake 提交于
Add a define for the maximum baud rate divisor, to improve code readability. Signed-off-by: NEd Blake <ed.blake@sondrel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 01 9月, 2017 1 次提交
-
-
由 Andy Shevchenko 提交于
After switching to HR timers for RS485 the NULL checks for the object inside timer functions become useless. Remove them to avoid confusion to static analyzers. Fixes 6e0a5de2 ("serial: 8250: Use hrtimers for rs485 delays") Cc: Colin Ian King <colin.king@canonical.com> Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 29 8月, 2017 2 次提交
-
-
由 Sean Wang 提交于
MediaTek BTIF controller is the serial interface similar to UART but it works only as the digital device which is mainly used to communicate with the connectivity module called CONNSYS inside the SoC which could be mostly found on those MediaTek SoCs with Bluetooth feature such as MT7622 and MT7623 SoCs. And the controller is made as being compatible with the 8250 register layout with extra registers such as DMA enablement so it tends to be integrated with reusing 8250 OF driver. However, DMA mode is not being supported yet in the current driver. Signed-off-by: NSean Wang <sean.wang@mediatek.com> Suggested-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Rafael Gago 提交于
Previously the timers where based on the classic timers, giving a too coarse resolution on systems with configs of less than 1000 HZ. This patch changes the rs485 timers to hrtimers. Signed-off-by: NRafael Gago Castano <rgc@hms.se> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 30 7月, 2017 1 次提交
-
-
由 Andy Shevchenko 提交于
First 16 bits in the flags field are user-visible except UPF_NO_TXEN_TEST. To keep it clean we introduce internal quirks and move UPF_NO_TXEN_TEST to them. Rename the constant to UPQ_NO_TXEN_TEST to distinguish with port flags. Users are converted accordingly. The quirks field might be extended later to hold the additional ones. Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 29 6月, 2017 1 次提交
-
-
由 Phil Elwell 提交于
The BCM2835 MINI UART has non-standard THRE semantics. Conventionally the bit means that the FIFO is empty (although there may still be a byte in the transmit register), but on 2835 it indicates that the FIFO is not full. This causes interrupts after every byte is transmitted, with the FIFO providing some interrupt latency tolerance. A consequence of this difference is that the usual strategy of writing multiple bytes into the TX FIFO after checking THRE once is unsafe. In the worst case of 7 bytes in the FIFO, writing 8 bytes loses all but the first since by then the FIFO is full. There is an HFIFO ("Hidden FIFO") capability that causes the transmit loop to terminate when both THRE and TEMT are set, i.e. when the TX block is completely idle. This is unnecessarily cautious, potentially causing gaps in transmission. Add a new conditional to the transmit loop, predicated on CAP_MINI, that exits when THRE is no longer set (the FIFO is full). This allows the FIFO to fill quickly but subsequent writes are paced by the transmission rate. Signed-off-by: NPhil Elwell <phil@raspberrypi.org> Acked-by: NEric Anholt <eric@anholt.net> Acked-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 24 5月, 2017 1 次提交
-
-
由 Phil Elwell 提交于
The AUX/mini-UART in the BCM2835 family of procesors is a cut-down 8250 clone. In particular it is lacking support for the following features: CSTOPB PARENB PARODD CMSPAR CS5 CS6 Add a new capability (UART_CAP_MINI) that exposes the restrictions to the user of the termios API by turning off the unsupported features in the request. N.B. It is almost possible to automatically discover the missing features by reading back the LCR register, but the CSIZE bits don't cooperate (contrary to the documentation, both bits are significant, but CS5 and CS6 are mapped to CS7) and the code is much longer. See: https://github.com/raspberrypi/linux/issues/1561Signed-off-by: NPhil Elwell <phil@raspberrypi.org> Acked-by: NEric Anholt <eric@anholt.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 18 5月, 2017 3 次提交
-
-
由 Jan Kiszka 提交于
After migrating 8250_exar to MSI in 172c33cb, we can get stuck without further interrupts because of the special wake-up event these chips send. They are only cleared by reading INT0. As we fail to do so during startup and shutdown, we can leave the interrupt line asserted, which is fatal with edge-triggered MSIs. Add the required reading of INT0 to startup and shutdown. Also account for the fact that a pending wake-up interrupt means we have to return 1 from exar_handle_irq. Drop the unneeded reading of INT1..3 along with this - those never reset anything. An alternative approach would have been disabling the wake-up interrupt. Unfortunately, this feature (REGB[17] = 1) is not available on the XR17D15X. Fixes: 172c33cb ("serial: exar: Enable MSI support") Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com> Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Ard Biesheuvel 提交于
Commit fa01e2ca ("serial: 8250: Integrate Fintek into 8250_base") modified the probing logic for PNP0501 devices, to remove a collision between the generic 16550A driver and the Fintek driver, which reused the same ACPI _HID. The Fintek device probe is now incorporated into the common 8250 probe path, and gets called for all discovered 16550A compatible devices, including ones that are MMIO mapped rather than IO mapped. However, the Fintek driver assumes the port base is a I/O address, and proceeds to probe some arbitrary offsets above it. This is generally a wrong thing to do, but on ARM systems (having no native port I/O), this may result in faulting accesses of completely unrelated MMIO regions in the PCI I/O space. Given that this is at serial probe time, this results in hard to diagnose crashes at boot. So let's restrict the Fintek probe to devices that we know are using port I/O in the first place. Fixes: fa01e2ca ("serial: 8250: Integrate Fintek into 8250_base") Suggested-by: NArnd Bergmann <arnd@arndb.de> Reviewed-by: NRicardo Ribalda <ricardo.ribalda@gmail.com> Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Joel Stanley 提交于
The probing of THRE irq behaviour assumes the other end will be reading bytes out of the buffer in order to probe the port at driver init. In some cases the other end cannot be relied upon to read these bytes, so provide a flag for them to skip this step. Bit 19 was chosen as the flags are a int and the top bits are taken. Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NJoel Stanley <joel@jms.id.au> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 18 4月, 2017 1 次提交
-
-
由 Marc Gonzalez 提交于
Define an OF early console for Palmchip UART, which can be enabled by passing "earlycon" on the boot command line. Signed-off-by: NMarc Gonzalez <marc_gonzalez@sigmadesigns.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 10 2月, 2017 1 次提交
-
-
由 Jan Kiszka 提交于
None of these registers is relevant for the userspace API. Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 12 1月, 2017 2 次提交
-
-
由 David Lechner 提交于
This adds a new UART port type for TI DA8xx/OMAPL13x/AM17xx/AM18xx/66AK2x. These SoCs have standard 8250 registers plus some extra non-standard registers. The UART will not function unless the non-standard Power and Emulation Management Register (PWREMU_MGMT) is configured correctly. This is currently handled in arch/arm/mach-davinci/serial.c for non-device-tree boards. Making this part of the UART driver will allow UART to work on device-tree boards as well and the mach code can eventually be removed. Signed-off-by: NDavid Lechner <david@lechnology.com> Acked-by: NSekhar Nori <nsekhar@ti.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Alexey Brodkin 提交于
With CONFIG_DYNAMIC_DEBUG if dyndbg enables debug output in 8250_port.c deadlock happens inevitably on UART IRQ handling. That's the problematic execution path: ---------------------------->8------------------------ UART IRQ: serial8250_interrupt() -> serial8250_handle_irq(): lock "port->lock" -> pr_debug() -> serial8250_console_write(): bump in locked "port->lock". OR (if above pr_debug() gets removed): serial8250_tx_chars() -> pr_debug() -> serial8250_console_write(): bump in locked "port->lock". ---------------------------->8------------------------ So let's get rid of those not that much useful debug entries. Discussed problem could be easily reproduced with QEMU for x86_64. As well as this fix could be mimicked with muting of dynamic debug for the problematic lines as simple as: ---------------------------->8------------------------ dyndbg="+p; file 8250_port.c line 1756 -p; file 8250_port.c line 1822 -p" ---------------------------->8------------------------ Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com> Cc: Jiri Slaby <jslaby@suse.com> Cc: Peter Hurley <peter@hurleysoftware.com> Cc: Phillip Raffeck <phillip.raffeck@fau.de> Cc: Anton Wuerfel <anton.wuerfel@fau.de> Cc: "Matwey V. Kornilov" <matwey@sai.msu.ru> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Thor Thayer <tthayer@opensource.altera.com> Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 11 1月, 2017 1 次提交
-
-
由 Daniel Jedrychowski 提交于
When in RS485 emulation mode, __do_stop_tx_rs485() calls serial8250_clear_fifos(). This not only clears the FIFOs, but also sets all bits in their control register (UART_FCR) to 0. One of the effects of this is the disabling of the FIFOs, which turns them into single-byte holding registers. The rest of the driver doesn't know this, which results in the lions share of characters passed into a write call to be dropped. (I can supply logic analyzer screenshots if necessary) This fix replaces the serial8250_clear_fifos() call to serial8250_clear_and_reinit_fifos() - this prevents the "dropped characters" issue from manifesting again while retaining the requirement of clearing the RX FIFO after transmission if the SER_RS485_RX_DURING_TX flag is disabled. Signed-off-by: NDaniel Jedrychowski <avistel@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 16 11月, 2016 2 次提交
-
-
由 Ed Blake 提交于
Expose set_ldisc() function so that it can be overridden with a platform specific implementation. Signed-off-by: NEd Blake <ed.blake@imgtec.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Andy Shevchenko 提交于
The following fix of runtime PM use in DMA mode requires at least serial8250_rpm_put_tx() to be available. Export both calls. Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 27 10月, 2016 1 次提交
-
-
由 Steve Shih 提交于
NXP SC16C2552 requires that we always write a reset to the RX FIFO and TX FIFO whenever we enable the FIFOs Cc: xe-kernel@external.cisco.com Signed-off-by: NSteve Shih <sshih@cisco.com> Signed-off-by: NDavid Singleton <davsingl@cisco.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 27 9月, 2016 1 次提交
-
-
由 Thor Thayer 提交于
The Altera 16550 soft IP UART requires 2 additional registers for TX FIFO threshold support. These 2 registers enable the TX FIFO Low Watermark and set the TX FIFO Low Watermark. Set the TX FIFO threshold to the FIFO size - tx_loadsz. Signed-off-by: NThor Thayer <tthayer@opensource.altera.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 22 9月, 2016 1 次提交
-
-
由 Jiri Olsa 提交于
First loop in wait_for_xmitr could also trigger NMI watchdog in case reading from the port is slow: PID: 0 TASK: ffffffff819c1460 CPU: 0 COMMAND: "swapper/0" #0 [ffff88019f405e58] crash_nmi_callback at ffffffff8104d382 #1 [ffff88019f405e68] nmi_handle at ffffffff8168ead9 #2 [ffff88019f405eb0] do_nmi at ffffffff8168ec53 #3 [ffff88019f405ef0] end_repeat_nmi at ffffffff8168df13 [exception RIP: delay_tsc+50] RIP: ffffffff81325642 RSP: ffff88019f403bb0 RFLAGS: 00000083 RAX: 00000000000005c8 RBX: ffffffff81f83000 RCX: 0000024e4fb88a8b RDX: 0000024e4fb89053 RSI: 0000000000000000 RDI: 00000000000007d1 RBP: ffff88019f403bb0 R8: 000000000000000a R9: 0000000000000000 R10: 0000000000000000 R11: ffff88019f403ad6 R12: 000000000000250f R13: 0000000000000020 R14: ffffffff81d360c7 R15: 0000000000000047 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 --- <NMI exception stack> --- #4 [ffff88019f403bb0] delay_tsc at ffffffff81325642 #5 [ffff88019f403bb8] __const_udelay at ffffffff813255a8 #6 [ffff88019f403bc8] wait_for_xmitr at ffffffff81404390 #7 [ffff88019f403bf0] serial8250_console_putchar at ffffffff8140455c #8 [ffff88019f403c10] uart_console_write at ffffffff813ff00a #9 [ffff88019f403c40] serial8250_console_write at ffffffff814044ae #10 [ffff88019f403c88] call_console_drivers.constprop.15 at ffffffff81086b01 #11 [ffff88019f403cb0] console_unlock at ffffffff8108842f #12 [ffff88019f403ce8] vprintk_emit at ffffffff81088834 #13 [ffff88019f403d58] vprintk_default at ffffffff81088ba9 #14 [ffff88019f403d68] printk at ffffffff8167f034 Adding touch_nmi_watchdog call to the first loop as well. Reported-by: NChunyu Hu <chuhu@redhat.com> Signed-off-by: NJiri Olsa <jolsa@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 02 9月, 2016 2 次提交
-
-
由 Andy Shevchenko 提交于
Unify the check of em485 variable to be either (em485) or (!em485) instead of the explicit comparison to NULL. While here, remove redundant check in __do_stop_tx_rs485() and __stop_tx_rs485() since the functions ain't called with NULL value of em485 variable. Cc: "Matwey V. Kornilov" <matwey@sai.msu.ru> Tested-by: NYegor Yefremov <yegorslists@googlemail.com> Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Andy Shevchenko 提交于
There are calls to serial8250_rpm_{get|put}() in __do_stop_tx_rs485() that are certainly placed in a wrong location. I dunno how it had been tested with runtime PM enabled because it is obvious "sleep in atomic context" error. Besides that serial8250_rpm_get() is called immediately after an IO just happened. It implies that the device is already powered on, see implementation of serial8250_em485_rts_after_send() and serial8250_clear_fifos() for the details. There is no bug have been seen due to, as I can guess, use of auto suspend mode when scheduled transaction to suspend is invoked quite lately than it's needed for a few writes to the port. It might be possible to trigger a warning if stop_tx_timer fires when device is suspended. Refactor the code to use runtime PM only in case of timer function. Fixes: 0c66940d ("tty/serial/8250: fix RS485 half-duplex RX") Cc: "Matwey V. Kornilov" <matwey@sai.msu.ru> Tested-by: NYegor Yefremov <yegorslists@googlemail.com> Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 31 8月, 2016 3 次提交
-
-
由 Andy Shevchenko 提交于
Intel Quark has 16550A compatible UART with autoflow feature enabled. It has only 16 bytes of FIFO. Currently serial8250_do_set_termios() prevents to enable autoflow since the minimum requirement of 32 bytes of FIFO size. Drop a FIFO size limitation to allow autoflow control be enabled on such UARTs. While here, comment out UART_CAP_AFE for PORT_AR7 since it wasn't working and it will be not a good idea to use it in conjunction with trigger level of 1 byte. Suggested-by: NPeter Hurley <peter@hurleysoftware.com> Reviewed-by: NPeter Hurley <peter@hurleysoftware.com> Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: NBryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Eddie Huang 提交于
mediatek can support baud rate up to 4M. the 'uart_get_baud_rate' function will limit the max baud rate. Modify max baud to remove the limit. Signed-off-by: NLong Cheng <long.cheng@mediatek.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Andy Shevchenko 提交于
Serial console is broken in v4.8-rcX. Mika and I independently bisected down to commit 4ef03d32 ("tty/serial/8250: use mctrl_gpio helpers"). Since neither author nor anyone else didn't propose a solution we better revert it for now. This reverts commit 4ef03d32. Link: https://lkml.kernel.org/r/20160809130229.GN1729@lahna.fi.intel.comSigned-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com> Tested-by: NMika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 26 6月, 2016 3 次提交
-
-
由 Yegor Yefremov 提交于
This patch permits the usage for GPIOs to control the CTS/RTS/DTR/DSR/DCD/RI signals. Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Yegor Yefremov 提交于
Introduce serial8250_out_MCR() and serial8250_in_MCR() routines, that replace following calls: serial_out(port, UART_MCR, val) serial_port_out(up, UART_MCR, val) serial_in(port, UART_MCR) This patch is needed in order to integrate reading/writing of MCR signals via SERIAL_MCTRL_GPIO infrastructure later. Reviewed-by: NPeter Hurley <peter@hurleysoftware.com> Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Jiri Slaby 提交于
The compiler complains about variables that are set, but never used: * intX variables in exar_handle_irq drivers/tty/serial/8250/8250_port.c:1864:34: warning: variable ‘int3’ set but not used [-Wunused-but-set-variable] * val variable in pci_quatech_wqopr drivers/tty/serial/8250/8250_pci.c:1139:10: warning: variable ‘val’ set but not used [-Wunused-but-set-variable] And about a shadow variable: * tmout in wait_for_xmitr is defined twice with the same type. Both of them are also initialized before use. Remove all of them. Signed-off-by: NJiri Slaby <jslaby@suse.cz> Cc: Matt Schulte <matts@commtech-fastcom.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 25 6月, 2016 1 次提交
-
-
由 Jiri Slaby 提交于
Convert DEBUG_INTR to pr_debug: * defined semantics (DEBUG, DYNAMIC_DEBUG) * KERN_DEBUG level instead of KERN_DEFAULT * emit __func__ and \n * verified 'fmt' even when !DEBUG I wonder if anybody ever used that or whether we should just drop the lines. Signed-off-by: NJiri Slaby <jslaby@suse.cz> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 01 5月, 2016 5 次提交
-
-
由 Ricardo Ribalda Delgado 提交于
The 8250_fintek driver advertises as the PNP0501 driver; however this conflicts with the standard 16550A uart PNP0501. The conflict causes the 8250_fintek driver to load with _every_ PNP0501, but never probe, and causing the entire 8250 driver stack to unload if the 8250_fintek driver is unloaded (modprobe doesn't know that 8250_pnp rather than 8250_fintek claimed the resource). This patch merges the Fintek driver into 8250_base. On autoconfig_16550 the device is probed to verify if it is a FINTEK device or not. This custom probing can be disabled completely via configuration. When a Fintek device is not probed it will behave as a standard 16550A device, with no RS485 capabilities. Reported-by: NPeter Hurley <peter@hurleysoftware.com> Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com> Reviewed-by: NPeter Hurley <peter@hurleysoftware.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Peter Hurley 提交于
Using fake IIR values to perform rx dma operations unnecessarily conflates separate operations, stopping in-progress dma with starting new dma. Introduce serial8250_rx_dma_flush() to handle stopping in-progress dma [omap8250 already has equivalent omap_8250_rx_dma_flush()]. Replace rx_dma(UART_IIR_RX_TIMEOUT) with the equivalent *_rx_dma_flush(), and rx_dma(0) with the equivalent *_rx_dma(). Handle IIR steering in the irq handler with handle_rx_dma() helper. Signed-off-by: NPeter Hurley <peter@hurleysoftware.com> Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Peter Hurley 提交于
If !up->dma == F, then up->dma == T and can be elided from the (up->dma && up->dma->tx_err) sub-expression. Signed-off-by: NPeter Hurley <peter@hurleysoftware.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Peter Hurley 提交于
dma_err is not used other than for boolean evaluation; substitute the actual operation directly. Signed-off-by: NPeter Hurley <peter@hurleysoftware.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Wan Ahmad Zainie 提交于
Exposes get_mctrl() function so that it can be overriden with platform specific implementation. Signed-off-by: NWan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com> Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-