Convert to new network device ops interface. Compile tested only.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use dev_printk() instead of printk() to give a little more context
and use consistent format.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
igb_set_wol().  Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: N"Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.

Drivers need not do it any more.

Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A number of places still use %02x:...:%02x because it's
in debug statements or for no real reason. Make a few
of them use %pM.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a bool IGB_DCA defined to y if IGB and DCA are enabled, but IGB isn't y while DCA=m.  And thus remove the need to select INTEL_IOATDMA when IGB is enabled, so that non-x86 architectures can build the igb driver.
Based on work/patch from Brice Goglin <brice@myri.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The 82575 has an issue in which the DMA will go out of sync if the link
partner goes into an L0s state.  To prevent this we set the pci-e link
partner capability bits to disable the L0s transition on the hw.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Remove code that was in place to support fake netdev
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The cleaned variable can be replaced by the count of packets cleaned during
the tx interrupt routine so it can be removed.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Disable support for device 8086:10E8.  Currently the result of loading the
driver with the device present causes system instability.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The real_num_tx_queues was not being set when in MSI-X only mode.  This patch
corrects that path so all interrupt types are correctly configured.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Set the EICS bit for each of the RX queues at least once every 2 seconds to
prevent the rx queues from stalling.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

igb_init_managability does not actually perform any function as the two
registers it attempts to write are both read only on the host.  This patch
removes the function and all references to it from the driver.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

With a fiber or serdes NIC installed the driver was causing a null pointer
dereference on driver unload.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The internal name was used in comments, replaced with silicon part number.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

drivers/net/igb/igb_main.c:388:20: warning: Using plain integer as NULL pointer
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

With the recent changes to tx mutiqueue, igb/ixgbe/e1000e was not calling
netif_tx_start_all_queues() before calling netif_tx_wake_all_queues().
This causes an issue during loading of the driver.

In addition, updated e1000e to use the updated tx mutliqueue api.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This effectively "flips the switch" by making the core networking
and multiqueue-aware drivers use the new TX multiqueue structures.

Non-multiqueue drivers need no changes.  The interfaces they use such
as netif_stop_queue() degenerate into an operation on TX queue zero.
So everything "just works" for them.

Code that really wants to do "X" to all TX queues now invokes a
routine that does so, such as netif_tx_wake_all_queues(),
netif_tx_stop_all_queues(), etc.

pktgen and netpoll required a little bit more surgery than the others.

In particular the pktgen changes, whilst functional, could be largely
improved.  The initial check in pktgen_xmit() will sometimes check the
wrong queue, which is mostly harmless.  The thing to do is probably to
invoke fill_packet() earlier.

The bulk of the netpoll changes is to make the code operate solely on
the TX queue indicated by by the SKB queue mapping.

Setting of the SKB queue mapping is entirely confined inside of
net/core/dev.c:dev_pick_tx().  If we end up needing any kind of
special semantics (drops, for example) it will be implemented here.

Finally, we now have a "real_num_tx_queues" which is where the driver
indicates how many TX queues are actually active.

With IGB changes from Jeff Kirsher.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need for a feature bit for something that
can be tested by simply checking the TX queue count.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently VLAN filtering is enabled when the first VLAN is added.
Obviously before that there's no point in receiving any VLAN packets.
Now that we disable VLAN filtering in promiscous mode, we can keep
the VLAN filters enabled the remaining time.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As discussed in this thread:

http://www.mail-archive.com/netdev@vger.kernel.org/msg53976.html

promiscous mode means to disable *all* filters. Currently only unicast
and multicast filtering is disabled. This patch changes all Intel
drivers to also disable VLAN filtering.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Improve multiqueue performance
Change itr_val to reflect ITR timer value instead of ints/sec
Cleaned up AIM algorithms in general

Based on work by Mitch Williams
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Wrap hw variable declaration in DCA flags to prevent unused variable
warning during compilation.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Updates the suspend and resume to better handle the possibility of MSIX
vector changes.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds support for the use of the inet_lro module to provide
software LRO support.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds support for page recycling by splitting the page into two
usable portions and tracking the reference count.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Change igb from using a series of boolean operators to using a single flags
value that contains a number of different bit flags for all the different
features of the adapter.

This patch also adds WOL support for quad port adapters.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

We can remove a clunky workaround for not having the hardware
strip the CRC. 82575 silicon as well as the older PCI Express
e1000e hardware all work OK in this respect.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add DCA support in the similar method that it was added to the ixgbe
driver recently. DCA allows the network device to put data in the
CPU cache and notify the chipset of that event. This reduces cache
misses during receives.
Signed-off-by: NJeb Cramer <cramerj@intel.com>
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Addesses problems seen earlier with igb driver not correctly reporting rx
and tx stats.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This code adds multiple Tx queue infrastructure much like we
previously did in ixgbe. The MSI-X vector mapping is the bulk of
the change.

IAM can now be safely enabled and we've verified that it does
work correctly. We can also eliminate the tx ring lock.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The vlan_hwaccel_{rx,receive_skb} functions expect the full TCI field
for priority mappings, don't truncate the upper 4 bits.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update the NAPI implementation to use the new napi_struct infrstructure.
This removes the need of multiple net_device structs to implement a
multiqueue NAPI.
Signed-off-by: NPJ Waskiewicz <peter.p.waskiewicz.jr.@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch resolves an issue seen on 82575 adapters with managability
pass-thru enabled, which could cause the system to panic.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Currently there are items in the driver to support parameters, but there
are no parameters being added to the driver.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Simplify a bunch of calls to these functions by moving the adapter
struct out of the function arguments since that is not needed.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch makes igb driver ioport-free.
This corrects behavior in probe function so as not to request ioport
resources as long as they are not really needed.
Signed-off-by: NTaku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>