- 03 10月, 2013 1 次提交
-
-
由 Emmanuel Grumbach 提交于
Newer firmware fixed a bug that prevented to use CTS to self. Firmwares with API greater than 8 have this bug fixed. Enable the feature for these firmwares only. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 31 7月, 2013 1 次提交
-
-
由 Ilan Peer 提交于
Return in case that HW restart is in progress but the added interface is not found during the iteration over all the interfaces. Signed-off-by: NIlan Peer <ilan.peer@intel.com> Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 25 6月, 2013 1 次提交
-
-
由 Ilan Peer 提交于
In case that an AP/GO interface is started while there is a station/P2P client associated, need to make sure that the AP/GO beacon time is far enough from the station's one in oder to allow the station to receive the DTIM beacons and the following traffic etc. To resolve this, when the AP is started, check if there is an active station interface, and guarantee that the AP/GO TBTT is far enough from the station one. Signed-off-by: NIlan Peer <ilan.peer@intel.com> Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 12 6月, 2013 1 次提交
-
-
由 Emmanuel Grumbach 提交于
The MCAST queue should be enabled after DTIM only. According to fw API, the MCAST must not be attached to any station, but should appear in the mcast_qid of the AP's mac context only. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 04 6月, 2013 1 次提交
-
-
由 Emmanuel Grumbach 提交于
The AP mode needs to use the MCAST fifo for the MCAST frames sent after the DTIM. This fifo needs to be configured with the same parameters as the VOICE FIFO. A separate SCD queue is mapped to this fifo - the cab_queue (cab stands for Content After Beacon). This queue isn't connected to any station, but rather to the MAC context. This queue should (and is already) be set as the MCAST queue - this is part of the of MAC context command. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Reviewed-by: NIlan Peer <ilan.peer@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 29 5月, 2013 2 次提交
-
-
由 Hila Gonen 提交于
The firmware supports periodic keep alive and beacon monitoring, so advertise connection monitor offload capability by setting IEEE80211_HW_CONNECTION_MONITOR flag. Implement missed beacons notification handler. Call ieee80211_beacon_loss in case of missed beacons, so AP probing by mac80211 can be triggered. Signed-off-by: NHila Gonen <hila.gonen@intel.com> Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Eytan Lifshitz 提交于
In order to avoid NIC destruction due to high temperature, CT kill will power down the NIC. To avoid this, thermal throttling will decrease throughput to prevent the NIC from reaching the temperature at which CT kill is performed. Signed-off-by: NEytan Lifshitz <eytan.lifshitz@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 17 5月, 2013 1 次提交
-
-
由 Alexander Bondar 提交于
In the normal flow first MAC_CONTEXT_CMD for particular interface is never sent while associated. The exception is fw restart flow when resuming from suspend when WoWLAN is enabled. In this case successive "add" and "modify" MAC_CONTEXT_CMD commands may be sent with assoc flag set what cause FW mal functioning. To prevent this never set assoc flag in MAC_CONTEXT_CMD with action "add". Cc: stable@vger.kernel.org Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com> Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 22 3月, 2013 1 次提交
-
-
由 Janusz Dziedzic 提交于
Add P2P NoA settings for STA mode. Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com> [fix docs] Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 20 3月, 2013 4 次提交
-
-
由 Emmanuel Grumbach 提交于
This is the right source of information for the valid Tx antennas, not the NVM. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
In firmware "listener" (monitor) mode, we still need to open up the filters with the filter flags to receive all frames. Reviewed-by: NIlan Peer <ilan.peer@intel.com> Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Ilan Peer 提交于
Signed-off-by: NIlan Peer <ilan.peer@intel.com> Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Ilan Peer 提交于
Mostly for debugging purposes Signed-off-by: NIlan Peer <ilan.peer@intel.com> Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 06 3月, 2013 4 次提交
-
-
由 Johannes Berg 提交于
When modifying a MAC, we update its beacon system time which is taken as a base to calculate TBTT. The firmware doesn't use the new timestamp because the time is never used after the MAC and broadcast station were added, but it is safer to not rely on this and avoids the overhead of reading the register every time the MAC is updated. Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Reviewed-by: NIlan Peer <ilan.peer@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Ilan Peer 提交于
1. For P2P Device filter in only probe requests. 2. For station mode filter in all group cast frames, and in addition beacons as long as we are not associated. 3. For AP/GO filter in all group cast and in addition probe requests. Signed-off-by: NIlan Peer <ilan.peer@intel.com> Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Dor Shaish 提交于
The current fw doesn't currently support cts to self. There is a bug in the fw that prevents us from using cts to self. Use full protection (including RTS) for now. Signed-off-by: NDor Shaish <dor.shaish@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Emmanuel Grumbach 提交于
7000.c was released as GPL only by mistake: it should be dual licensed - GPL / BSD. The file that contains the license in the kernel is COPYING and not LICENSE.GPL. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 19 2月, 2013 3 次提交
-
-
由 Ilan Peer 提交于
Signed-off-by: NIlan Peer <ilan.peer@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Ilan Peer 提交于
The time event data structures are required also for P2P Device interface. Signed-off-by: NIlan Peer <ilan.peer@intel.com> Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
For the firmware to know when DTIM beacons arrive we have to program the DTIM time in TSF and system time in the MAC context. Since mac80211 now tracks the different times (on demand), this becomes easy. Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 12 2月, 2013 1 次提交
-
-
由 Johannes Berg 提交于
If we haven't heard a beacon before we associate we can still start the association process and set the MAC in the firmware to associated only after having received a beacon with DTIM period by reacting to the new change flag (BSS_CHANGED_DTIM_PERIOD) from mac80211. This reduces the association time in these cases. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 01 2月, 2013 1 次提交
-
-
由 Johannes Berg 提交于
Newer firmware revisions have a completely new firmware API. This is the new driver for this new API. I've listed the people who directly contributed code, but many others from various teams have contributed in other ways. Cc: Alexander Bondar <alexander.bondar@intel.com> Cc: Amit Beka <amit.beka@intel.com> Cc: Amnon Paz <amnonx.paz@intel.com> Cc: Assaf Krauss <assaf.krauss@intel.com> Cc: David Spinadel <david.spinadel@intel.com> Cc: Dor Shaish <dor.shaish@intel.com> Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Cc: Eytan Lifshitz <eytan.lifshitz@intel.com> Cc: Ilan Peer <ilan.peer@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-