Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 160
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 03 10月, 2013 5 次提交
  3. 13 9月, 2013 2 次提交
    • M
      Remove GENERIC_HARDIRQ config option · 0244ad00
      由 Martin Schwidefsky 提交于 
      After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
      0244ad00
    • M
      MIPS: DECstation I/O ASIC DMA interrupt handling fix · 5359b938
      由 Maciej W. Rozycki 提交于 
      This change complements commit d0da7c002f7b2a93582187a9e3f73891a01d8ee4
and brings clear_ioasic_irq back, renaming it to clear_ioasic_dma_irq at
the same time, to make I/O ASIC DMA interrupts functional.

Unlike ordinary I/O ASIC interrupts DMA interrupts need to be deasserted
by software by writing 0 to the respective bit in I/O ASIC's System
Interrupt Register (SIR), similarly to how CP0.Cause.IP0 and CP0.Cause.IP1
bits are handled in the CPU (the difference is SIR DMA interrupt bits are
R/W0C so there's no need for an RMW cycle).  Otherwise the handler is
reentered over and over again.

The only current user is the DEC LANCE Ethernet driver and its extremely
uncommon DMA memory error handler that does not care when exactly the
interrupt is cleared.  Anticipating the use of DMA interrupts by the Zilog
SCC driver this change however exports clear_ioasic_dma_irq for device
drivers to choose the right application-specific sequence to clear the
request explicitly rather than calling it implicitly in the .irq_eoi
handler of `struct irq_chip'.  Previously these interrupts were cleared in
the .end handler of the said structure, before it was removed.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5826/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      5359b938
  5. 12 9月, 2013 11 次提交
  7. 11 9月, 2013 8 次提交
  9. 10 9月, 2013 1 次提交
  11. 07 9月, 2013 3 次提交
  13. 06 9月, 2013 10 次提交
    • O
      net: stmmac: fix bad merge conflict resolution · 356f9e74
      由 Olof Johansson 提交于 
      Merge commit 06c54055 did a bad conflict resolution accidentally
leaving out a closing brace.  Add it back.

This breaks a handful of defconfigs on ARM, so it'd be good to see it
applied pretty quickly.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      356f9e74
    • D
      bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize · c0a77ec7
      由 Dave Jones 提交于 
      The indentation here implies that the intent was for this to be a multiline if.
Introduced a few years ago in commit ec146a6f ("bnx2x: Modify XGXS functions")
Signed-off-by: NDave Jones <davej@fedoraproject.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      c0a77ec7
    • P
      vxlan: Fix kernel panic on device delete. · f011baf9
      由 Pravin B Shelar 提交于 
      On vxlan device create if socket create fails vxlan device is not
added to hash table. Therefore we need to check if device
is in hashtable before we delete it from hlist.
Following patch avoid the crash. net-next already has this fix.

---8<---
BUG: unable to handle kernel NULL pointer dereference at           (null)
IP: [<ffffffffa05f9ca7>] vxlan_dellink+0x77/0xf0 [vxlan]
PGD 42b2d9067 PUD 42e04c067 PMD 0
Oops: 0002 [#1] SMP
Modules linked in: vxlan(-)
Hardware name: Dell Inc. PowerEdge R620/0KCKR5, BIOS 1.4.8 10/25/2012
task: ffff88042ecf8760 ti: ffff88042f106000 task.ti: ffff88042f106000
RIP: 0010:[<ffffffffa05f9ca7>]  [<ffffffffa05f9ca7>]
vxlan_dellink+0x77/0xf0 [vxlan]
RSP: 0018:ffff88042f107e28  EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff88082af08000 RCX: ffff88083fd80000
RDX: 0000000000000000 RSI: ffff88042f107e58 RDI: ffff88042e12f810
RBP: ffff88042f107e48 R08: ffffffff8166eca0 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: ffff88082af087c0
R13: ffff88042e12f000 R14: ffff88042f107e58 R15: ffff88042f107e58
FS:  00007f4ed2de7700(0000) GS:ffff88043fc80000(0000)
knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 000000042e076000 CR4: 00000000000407e0
Stack:
 ffff88082af08000 ffffffff81654848 ffffffffa05fb4e0 ffffffff81654780
 ffff88042f107e98 ffffffff813b9c7a ffff88042f107e58 ffff88042f107e58
 ffff88042f107e88 ffffffffa05fb4e0 ffffffffa05fb780 ffff88042f107f18
Call Trace:
 [<ffffffff813b9c7a>] __rtnl_link_unregister+0xca/0xd0
 [<ffffffff813bb0e9>] rtnl_link_unregister+0x19/0x30
 [<ffffffffa05faa4c>] vxlan_cleanup_module+0x10/0x2f [vxlan]
 [<ffffffff81099fef>] SyS_delete_module+0x1cf/0x2c0
 [<ffffffff8146c069>] ? do_page_fault+0x9/0x10
 [<ffffffff8146f012>] system_call_fastpath+0x16/0x1b
Code: 4d 85 ed 0f 84 95 00 00 00 4c 8d a7 c0 07 00 00 49 8d bd 10 08 00
00 e8 28 e8 e6 e0 48 8b 83 c0 07 00 00 49 8b 54 24 08 48 85 c0 <48> 89
02 74 04 48 89 50 08 49 b8 00 02 20 00 00 00 ad de 4d 89
RIP  [<ffffffffa05f9ca7>] vxlan_dellink+0x77/0xf0 [vxlan]
 RSP <ffff88042f107e28>
CR2: 0000000000000000
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      f011baf9
    • T
      net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls · 15f59456
      由 Thomas Petazzoni 提交于 
      This commit implements the ->ndo_do_ioctl() operation so that the
PHY-related ioctl() calls can work from userspace, which allows
applications like mii-tool or mii-diag to do their job.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      15f59456
    • T
      net: mvneta: properly disable HW PHY polling and ensure adjust_link() works · 71408602
      由 Thomas Petazzoni 提交于 
      This commit fixes a long-standing bug that has been reported by many
users: on some Armada 370 platforms, only the network interface that
has been used in U-Boot to tftp the kernel works properly in
Linux. The other network interfaces can see a 'link up', but are
unable to transmit data. The reports were generally made on the Armada
370-based Mirabox, but have also been given on the Armada 370-RD
board.

The network MAC in the Armada 370/XP (supported by the mvneta driver
in Linux) has a functionality that allows it to continuously poll the
PHY and directly update the MAC configuration accordingly (speed,
duplex, etc.). The very first versions of the driver submitted for
review were using this hardware mechanism, but due to this, the driver
was not integrated with the kernel phylib. Following reviews, the
driver was changed to use the phylib, and therefore a software based
polling. In software based polling, Linux regularly talks to the PHY
over the MDIO bus, and sees if the link status has changed. If it's
the case then the adjust_link() callback of the driver is called to
update the MAC configuration accordingly.

However, it turns out that the adjust_link() callback was not
configuring the hardware in a completely correct way: while it was
setting the speed and duplex bits correctly, it wasn't telling the
hardware to actually take into account those bits rather than what the
hardware-based PHY polling mechanism has concluded. So, in fact the
adjust_link() callback was basically a no-op.

However, the network happened to be working because on the network
interfaces used by U-Boot for tftp on Armada 370 platforms because the
hardware PHY polling was enabled by the bootloader, and left enabled
by Linux. However, the second network interface not used for tftp (or
both network interfaces if the kernel is loaded from USB, NAND or SD
card) didn't had the hardware PHY polling enabled.

This patch fixes this situation by:

 (1) Making sure that the hardware PHY polling is disabled by clearing
     the MVNETA_PHY_POLLING_ENABLE bit in the MVNETA_UNIT_CONTROL
     register in the driver ->probe() function.

 (2) Making sure that the duplex and speed selections made by the
     adjust_link() callback are taken into account by clearing the
     MVNETA_GMAC_AN_SPEED_EN and MVNETA_GMAC_AN_DUPLEX_EN bits in the
     MVNETA_GMAC_AUTONEG_CONFIG register.

This patch has been tested on Armada 370 Mirabox, and now both network
interfaces are usable after boot.

[ Problem introduced by commit c5aff182 ("net: mvneta: driver for
  Marvell Armada 370/XP network unit") ]
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Jochen De Smet <jochen.armkernel@leahnim.org>
Cc: Peter Sanford <psanford@nearbuy.io>
Cc: Ethan Tuttle <ethan@ethantuttle.com>
Cc: Chény Yves-Gael <yves@cheny.fr>
Cc: Ryan Press <ryan@presslab.us>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: vdonnefort@lacie.com
Cc: stable@vger.kernel.org
Acked-by: NJason Cooper <jason@lakedaemon.net>
Tested-by: NVincent Donnefort <vdonnefort@gmail.com>
Tested-by: NYves-Gael Cheny <yves@cheny.fr>
Tested-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      71408602
    • J
      icplus: Use netif_running to determine device state · dfafb73f
      由 Jon Mason 提交于 
      Remove the __LINK_STATE_START check to verify the device is running, in
favor of netif_running().  netif_running() performs the same check of
__LINK_STATE_START, so the code should behave the same.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Sorbica Shieh <sorbica@icplus.com.tw>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      dfafb73f
    • V
      ethernet/arc/arc_emac: Fix huge delays in large file copies · 27082ee1
      由 Vineet Gupta 提交于 
      copying large files to a NFS mounted host was taking absurdly large
time.

Turns out that TX BD reclaim had a sublte bug.

Loop starts off from @txbd_dirty cursor and stops when it hits a BD
still in use by controller. However when it stops it needs to keep the
cursor at that very BD to resume scanning in next iteration. However it
was erroneously incrementing the cursor, causing the next scan(s) to
fail too, unless the BD chain was completely drained out.

[ARCLinux]$ ls -l -sh /disk/log.txt
 17976 -rw-r--r--    1 root     root       17.5M Sep  /disk/log.txt

========== Before =====================
[ARCLinux]$ time cp /disk/log.txt /mnt/.
real    31m 7.95s
user    0m 0.00s
sys     0m 0.10s

========== After =====================
[ARCLinux]$ time cp /disk/log.txt /mnt/.
real    0m 24.33s
user    0m 0.00s
sys     0m 0.19s
Signed-off-by: NVineet Gupta <vgupta@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com> (commit_signer:3/4=75%)
Cc: "David S. Miller" <davem@davemloft.net> (commit_signer:3/4=75%)
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: arc-linux-dev@synopsys.com
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      27082ee1
    • J
      tuntap: orphan frags before trying to set tx timestamp · 7bf66305
      由 Jason Wang 提交于 
      sock_tx_timestamp() will clear all zerocopy flags of skb which may lead the
frags never to be orphaned. This will break guest to guest traffic when zerocopy
is enabled. Fix this by orphaning the frags before trying to set tx time stamp.

The issue were introduced by commit eda29772
(tun: Support software transmit time stamping).

Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7bf66305
    • J
      tuntap: purge socket error queue on detach · 4bfb0513
      由 Jason Wang 提交于 
      Commit eda29772
(tun: Support software transmit time stamping) will queue skbs into error queue
when tx stamping is enabled. But it forgets to purge the error queue during
detach. This patch fixes this.

Cc: Richard Cochran <richardcochran@gmail.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4bfb0513
    • M
      qlcnic: use standard NAPI weights · df95fc44
      由 Michal Schmidt 提交于 
      Since commit 82dc3c63 ("net: introduce NAPI_POLL_WEIGHT")
netif_napi_add() produces an error message if a NAPI poll weight
greater than 64 is requested.

qlcnic requests the weight as large as 256 for some of its rings, and
smaller values for other rings. For instance in qlcnic_82xx_napi_add()
I think the intention was to give the tx+rx ring a bigger weight than
to rx-only rings, but it's actually doing the opposite. So I'm assuming
the weights do not really matter much.

Just use the standard NAPI weights for all rings.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Acked-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      df95fc44