The patch set beginning with commit:
"ARM: ux500: Apply a ste-* prefix onto snowball.dts"
thru commit:
"ARM: ux500: Remove u9540.dts as it's been replaced"
altered the names of the ux500 device tree files but forgot
to:

- Rename the ccu8540-pinctrl.dtsi file

- Update #include statements from files using these
  files, so the build broke.

- Update the Makefile for the device trees so the build
  broke.

Fix it up so we can build them all again.
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

It doesn't exist on the Snowball development board.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

TPS61052 is a; boost converter, LED driver, LED flash driver and
simple GPIO pin chip. It has no use here however, as it is not
found on the Snowball development board.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

It doesn't exist on the Snowball development board.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

It doesn't exist on this development board.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

Regulator names are platform independent, so they need to be applied to
the base level platform DTS files *.dts. Here we're supplying the names
for the newly described AB8500 external regulators.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

When this node was added, the AB8500 GPIO driver was pretty broken.
As a hack, we pretended that NOMADIK GPIO 26 was the correct on/off
pin, as it was unused. It worked because AB8500 GPIO 26 was in an
'always on from boot' state. Now the AB8500 GPIO driver is working,
the default state for all the pins is 'off'. Let's flip back over to
use the correct GPIO which is _actually_ attached to the regulator.

We're also taking the opportunity to straighten out some formatting
misdemeanours, swapping spaces for tabs.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

This removes the "0x" prefix in front of the I2C DT device
address designation for each I2C DT node in the ux500
devicetree files.
Reported-by: NBryan Wu <cooloney@gmail.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Fix typo of VAMIC2 LDO regulator name in some DT-related files.  This
patch replaces all occurrences with the right name.
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This switches to including <dt-bindings/interrupt-controller/irq.h>
and referencing the apropriate flags from there instead of
open-coding the flag numerals everywhere in the ux500 device
trees.
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch prepares the use of '#define' into dts files.
Signed-off-by: NGabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

In patch:
"ARM: ux500: Enable 100MHz for SD/SDIO/MMC devices"
the max frequency for the MMC/SD/SDIO adapters was
increased from 50 to 100MHz. Do the same for the
device tree boot path.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Gabriel Fernandez <gabriel.fernandez.st@gmail.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Commits:
"ARM: ux500: Add Device Tree nodes for the ux500 Crypt device"
"ARM: ux500: Add Device Tree nodes for the ux500 Hash device"

Added the crypto and hash devices conditionally, i.e. so as to
be turned on per-board by setting an "status" property on the
device from "disabled" to "okay" on each device.

This is wrong since this is an SoC feature, it is not board
dependent. It is the same ASIC under all circumstances and
functionality does not vary with board family.

This moves the enablement into the SoC file.
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch provides information required to setup ux500-hash when
booting with DT on the Snowball low-cost development platform.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch provides information required to setup ux500-crypt when
booting with DT on the Snowball low-cost development platform.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Ux500 regulator name for V-INTCORE is misspelled as vinitcore instead of
vintcore in some .dts file, causing the AB8500 regulator driver to not
bind properly.  Fix this by replacing all occurrences with the right
name.
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This root node is used in the whole family of chips, the a9500
is just one particular instance. Nodes should be named after
the type of object rather than identity.
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NGabriel Fernandez <gabriel.fernandez@stericsson.com>
Reviewed-by: NPhilippe Langlais <philippe.langlais@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Until recently platform code took care of all MMCI level-shifting by
way of an ios_handler() call-back. Now it is the driver's responsibility
to handle. In order to so that we need to provide the VQMMC regulator
reference in Device Tree. This patch takes care of that.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

When the thermal DT node was inserted a new PRCMU node was created;
however, one already exists in the Snowball DTS file. Here we
amalgamate the two into a single consolidated node.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The ab8500 device is a child of the prcmu device, which is a memory mapped
bus device, whose children are addressable using physical memory addresses,
not using mailboxes, so a mailbox number in the ab8500 node cannot be
parsed by DT. Nothing uses this number, since it was only introduced
as part of the failed attempt to clean up prcmu mailbox handling, and
we can simply remove it.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The AB8500 GPIO driver has been un-BROKEN and rewritten as a pinctrl
driver. Now that it's back in use, let's ensure that it's available
when booting Snowball with Device Tree enabled.

Cc: arm@kernel.org
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch adds device tree properties for ST-Ericsson DB8500 thermal driver,
also adds the platform data to support the old fashion.
Signed-off-by: Nhongbo.zhang <hongbo.zhang@linaro.com>
Reviewed-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NZhang Rui <rui.zhang@intel.com>

So far, each ST-Ericsson board supported by Device Tree has been similar
enough to run though a single DT_MACHINE_INIT call. On the back of that
it has been suggested that we should reduce the number of compatible
strings in our dt_compat structure. After subsequent discussion with Arnd
Bergmann the conclusion was to list entries by platform as opposed to by
board.

The other suggestion was to use a single string which would cover all
supported platforms, but any wildcard entries would include unsupported
chipsets, such as the u5500 and potential new chips which no not yet have
DT functionality. Hence, the best solution which encompasses all supported
platforms, but no unsupported ones was to list the currently enabled four
chipsets; u8500, u8540, u9500 and u9540 instead.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Snowball's external SD/MMC slot is only capable of 4 bit data
transfer, not 8 bits as previously thought. This is a simple
fixup moving to the correct settings.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

In the DB8500 Reference Manual SDI devices are described as being
part of peripheral blocks. This is more in line with how these devices
are actually represented in hardware, so here we detail which
peripheral block each of the SDI devices belong in the node name.
Requested-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Regulator supply names should be allocated by board rather than
per SoC, as the same SoC could be wired differently on varying
hardware. Here we push all regulator-name allocation out to the
dbx5x0 subordinate board files; HREF and Snowball.
Requested-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This property has no place here as the populated node is not related
to a GPIO controller.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This is where we link together all of the SoC sound components for
a given platform. This all encompassing sound node is only found
in the very lowest hierarchical DTS file, since the component mix may
well change from board variant to board variant.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch inserts all known MSP devices into the DBx5x0 Device Tree
disabled and enables the two important ones for the Snowball low-cost
development board.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch configures the user LED on Snowball to double flash
every second or so, whilst it's still alive. This can give key
indications as to what the board is doing in the case of no
console output.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch enables and illuminates the user_led on the
Snowball low-cost development board using DT. It also
removes initialisation carried out from platform code.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Allow proper initialisation for MMC via the mmci driver
for the Snowball low-cost development board using DT. At
the moment we continue to use DMA setup from platform code.
Once the DMA generic DT bindings have been completed we
can then port the remainder over to DT.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Here we supply the information required to setup regulators successfully
on Snowball and other db8500 variants which use the ab8500 regulators.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This patch adds a fixed regulator for use by the SMSC911x Ethernet
chip driver into the db8500 Device Tree. It also references other
regulators required by the same device.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This patch applies the correct format requested by the irq
domain. For chained IRQs which use GPIO lines as IRQs, we
stipulate that a two cell request is required. The first cell
contains the requested IRQ and the second can contain flags
pertaining to edge detection and level sensitive values. The
zeroth cell specifies the GPIO controller by use of a phandle.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Here we split the description of the external-bus@50000000 over
two description files. In the more generic db8500 description file
we only specify the external-bus. Normally this would be used to
communicate with a NOR-flash device. On the Snowball however, the
SMSC9115 Ethernet chip occupies it. In the Snowball board specific
description file is where we actually specify that it is in fact the
Ethernet device which lives here.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Ensure each button is individually identifiable by using
their correct unique given device names.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This creates Device Tree bindings for the Nomadik GPIO driver.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
[Split off from the patch actually implementing the bindings]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>