In order to use the HDA codec to forward audio data to the HDMI codec it
needs the ELD that is parsed from the monitor's EDID.

Also implement an interoperability mechanism between the HDA controller
and the HDMI codec. This uses vendor-defined scratch registers to pass
data from the HDMI codec driver to the HDMI driver (that implements the
receiving end of the HDMI codec). A custom format is used to pass audio
sample rate and channel count to the HDMI driver.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Current generations of Tegra do not support deep color modes, so force
8 bits per color even if the connected monitor or panel supports more.
Signed-off-by: NThierry Reding <treding@nvidia.com>

The code to set a video mode is common to all types of outputs that the
SOR can drive. Extract it into a separate function so that it can be
shared.
Signed-off-by: NThierry Reding <treding@nvidia.com>

This function is useful in both eDP and DP modes, so split it out in
anticipation of adding DP support.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Use a slightly more sensible name, tegra_sor_compute_config().
Signed-off-by: NThierry Reding <treding@nvidia.com>

Switching the SOR parent clock can glitch if done while the clock is
enabled. Extract a common function that can be used to disable the
module clock, switch the parent and reenable the module clock.
Signed-off-by: NThierry Reding <treding@nvidia.com>

The DPAUX pins are shared with an internal I2C controller. To allow
these pins to be muxed to the I2C controller, register a pinctrl device
for the DPAUX device.

This is based upon work by Thierry Reding <treding@nvidia.com>.
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

To utilise the DPAUX on Tegra, the SOR power partition must be enabled.
Now that Tegra supports the generic PM domain framework we manage the
SOR power partition via this framework for DPAUX. However, the sequence
for gating/ungating the SOR power partition requires that the DPAUX
reset is asserted/de-asserted at the time the SOR power partition is
gated/ungated, respectively. Now that the reset control core assumes
that resets are exclusive, the Tegra generic PM domain code and the
DPAUX driver cannot request the same reset unless we mark the resets as
shared. Sharing resets will not work in this case because we cannot
guarantee that the reset will be asserted/de-asserted at the appropriate
time. Therefore, given that the Tegra generic PM domain code will handle
the DPAUX reset, do not request the reset in the DPAUX driver if the
DPAUX device has a PM domain associated.
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

In preparation for adding pinctrl support for the DPAUX pads, add a
couple of helpers functions to configure the pads and control their
power.

Please note that although a simple if-statement could be used instead
of a case statement for configuring the pads as there are only two
possible modes, a case statement is used because when integrating with
the pinctrl framework, we need to be able to handle invalid modes that
could be passed.
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

If the probing of the DPAUX fails, then clocks are left enabled and the
DPAUX reset de-asserted. Add code to perform the necessary clean-up on
probe failure by disabling clocks and asserting the reset.
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

The local 'val' variable is used to store a value and immediately return
it to its caller, and hence serves no purpose. Just drop it and directly
return the value.
Signed-off-by: NThierry Reding <treding@nvidia.com>

This array never needs to be modified and therefore can be read-only
data.
Signed-off-by: NThierry Reding <treding@nvidia.com>

There's no need to wrap the BIT() macro into an extra set of parentheses
because it's already implemented to use its own set.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Insert a number of blank lines in places where they increase readability
of the code. Also collapse various variable declarations to shorten some
functions and finally rewrite some code for readability.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Fix a couple of occurrences where no blank line was used to separate
variable declarations from code or where block comments were wrongly
formatted.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Use kcalloc() to allocate arrays rather than passing the product of the
size per element by the number of elements to kzalloc().
Signed-off-by: NThierry Reding <treding@nvidia.com>

The local 'pos' variable doesn't serve any purpose other than being a
shortcut for pb->pos, but the result doesn't remove much, so simply drop
the local variable.
Signed-off-by: NThierry Reding <treding@nvidia.com>

find_first_zero_bit() returns an unsigned long, so make the local
variable that stores the result the same type for consistency.
Signed-off-by: NThierry Reding <treding@nvidia.com>

IDs can never be negative so use unsigned int. In some instances an
explicitly sized type (such as u32) was used for no particular reason,
so turn those into unsigned int as well for consistency.
Signed-off-by: NThierry Reding <treding@nvidia.com>

The number of channels, syncpoints, bases and mlocks can never be
negative, so use unsigned int instead of int. Also make loop variables
the same type for consistency.
Signed-off-by: NThierry Reding <treding@nvidia.com>

System workqueues have been able to handle high level of concurrency
for a long time now and there's no reason to use dedicated workqueues
just to gain concurrency. Since the workqueue host->intr_wq is involved
in sync point interrupts, and sync point wait and is not being used on
a memory reclaim path, dedicated host->intr_wq has been replaced with the
use of system_wq.

Unlike a dedicated per-cpu workqueue created with create_workqueue(),
system_wq allows multiple work items to overlap executions even on
the same CPU; however, a per-cpu workqueue doesn't have any CPU
locality or global ordering guarantees unless the target CPU is
explicitly specified and thus the increase of local concurrency
shouldn't make any difference.

cancel_work_sync() has been used  in _host1x_free_syncpt_irq() to ensure
that no work is pending by the time exit path runs.
Signed-off-by: NBhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NThierry Reding <treding@nvidia.com>

The pinconf-generic.h file exposes functions for creating generic mappings
but it does not expose a function for freeing the mappings. Add a function
for freeing generic mappings.
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The "simplified" prime multipliers made very bad hash functions, so get rid
of them.  This completes the work of 689de1d6.

To avoid the inefficiency which was the motivation for the "simplified"
multipliers, hash_64() on 32-bit systems is changed to use a different
algorithm.  It makes two calls to hash_32() instead.

drivers/media/usb/dvb-usb-v2/af9015.c uses the old GOLDEN_RATIO_PRIME_32
for some horrible reason, so it inherits a copy of the old definition.
Signed-off-by: NGeorge Spelvin <linux@sciencehorizons.net>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>

This reverts commit bff3c624.

Board "Leon" is otherwise known as "Toshiba CB35" and we already have
the entry that supports that board as of this commit :
963cb6fa platform/chrome: chromeos_laptop - Add Toshiba CB35 Touch

Remove this duplicate.
Signed-off-by: NBenson Leung <bleung@chromium.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The call to put_i2c_dev() frees "i2c_dev" so there is a use after
free when we call cdev_del(&i2c_dev->cdev).

Fixes: d6760b14 ('i2c: dev: switch from register_chrdev to cdev API')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

When EIC mode is in use (cpu_has_veic is true) enable it on each CPU
during GIC initialisation. Otherwise there may be a mismatch between the
hardware default interrupt model & that expected by the kernel.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Reviewed-by: NMatt Redfearn <matt.redfearn@imgtec.com>
Tested-by: NMatt Redfearn <matt.redfearn@imgtec.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13274/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

smack ->d_instantiate() uses ->setxattr(), so to be able to call it before
we'd hashed the new dentry and attached it to inode, we need ->setxattr()
instances getting the inode as an explicit argument rather than obtaining
it from dentry.

Similar change for ->getxattr() had been done in commit ce23e640.  Unlike
->getxattr() (which is used by both selinux and smack instances of
->d_instantiate()) ->setxattr() is used only by smack one and unfortunately
it got missed back then.
Reported-by: NSeung-Woo Kim <sw0312.kim@samsung.com>
Tested-by: NCasey Schaufler <casey@schaufler-ca.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Pwm config may sleep so defer it using a worker.

On a Freescale i.MX53 based board we ran into "BUG: scheduling while
atomic" because input_inject_event locks interrupts, but
imx_pwm_config_v2 sleeps.

Tested on Freescale i.MX53 SoC with 4.6.0.
Signed-off-by: NManfred Schlaegl <manfred.schlaegl@gmx.at>
Cc: stable@vger.kernel.org
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

added the according id and incresed XPAD_PKT_LEN to 64 as the elite
controller sends at least 33 byte messages [1].
Verified to be working by [2].

[1]: https://franticrain.github.io/sniffs/XboxOneSniff.html
[2]: https://github.com/paroj/xpad/issues/23Signed-off-by: NPierre-Loup A. Griffais <eduke32@plagman.net>
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: NPierre-Loup A. Griffais <eduke32@plagman.net>
Signed-off-by: NThomas Debesse <dev@illwieckz.net>
Signed-off-by: Naronschatz <aronschatz@aselabs.com>
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

After initially connecting a wired Xbox 360 controller or sending it
a command to change LEDs, a status/response packet is interpreted as
controller input. This causes the state of buttons represented in
byte 2 of the controller data packet to be incorrect until the next
valid input packet. Wireless Xbox 360 controllers are not affected.

Writing a new value to the LED device while holding the Start button
and running jstest is sufficient to reproduce this bug. An event will
come through with the Start button released.

Xboxdrv also won't attempt to read controller input from a packet
where byte 0 is non-zero. It also checks that byte 1 is 0x14, but
that value differs between wired and wireless controllers and this
code is shared by both. I think just checking byte 0 is enough to
eliminate unwanted packets.

The following are some examples of 3-byte status packets I saw:
01 03 02
02 03 00
03 03 03
08 03 00
Signed-off-by: NCameron Gutman <aicommander@gmail.com>
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

otherwise we lose ff commands: https://github.com/paroj/xpad/issues/27Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.

However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.

Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.

This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.

Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.

I was using this definition for testing:

 #define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
       unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))

which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.

I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.

[ Updated the 9p parts as per Al Viro  - Linus ]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds the Power Management Controller driver as a PCI driver
for Intel Core SoC architecture.

This driver can utilize debugging capabilities and supported features
as exposed by the Power Management Controller.

Please refer to the below specification for more details on PMC features.
http://www.intel.in/content/www/in/en/chipsets/100-series-chipset-datasheet-vol-2.html

The current version of this driver exposes SLP_S0_RESIDENCY counter.
This counter can be used for detecting fragile SLP_S0 signal related
failures and take corrective actions when PCH SLP_S0 signal is not
asserted after kernel freeze as part of suspend to idle flow
(echo freeze > /sys/power/state).

Intel Platform Controller Hub (PCH) asserts SLP_S0 signal when it
detects favorable conditions to enter its low power mode. As a
pre-requisite the SoC should be in deepest possible Package C-State
and devices should be in low power mode. For example, on Skylake SoC
the deepest Package C-State is Package C10 or PC10. Suspend to idle
flow generally leads to PC10 state but PC10 state may not be sufficient
for realizing the platform wide power potential which SLP_S0 signal
assertion can provide.

SLP_S0 signal is often connected to the Embedded Controller (EC) and the
Power Management IC (PMIC) for other platform power management related
optimizations.

In general, SLP_S0 assertion == PC10 + PCH low power mode + ModPhy Lanes
power gated + PLL Idle.

As part of this driver, a mechanism to read the SLP_S0_RESIDENCY is exposed
as an API and also debugfs features are added to indicate SLP_S0 signal
assertion residency in microseconds.

echo freeze > /sys/power/state
wake the system
cat /sys/kernel/debug/pmc_core/slp_s0_residency_usec
Signed-off-by: NRajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: NVishwanath Somayaji <vishwanath.somayaji@intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>

Some BIOSes unconditionally send an ACPI notification to RBTN when the
system is resuming from suspend. This makes dell-rbtn send an input
event to userspace as if a function key was pressed. Prevent this by
ignoring all the notifications received while the device is suspended.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=106031Signed-off-by: NGabriele Mazzotta <gabriele.mzt@gmail.com>
Tested-by: NAlex Hung <alex.hung@canonical.com>
Reviewed-by: NPali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>

Override default LED class suspend/resume handles, by keeping track of
the brightness level before suspending so that it can be automatically
restored on resume by calling default resume handler.
Signed-off-by: NMarco Trevisan (Treviño) <mail@3v1n0.net>
Acked-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>

aux0_show and aux1_show consists of almost identical code. Pull that
into a common helper and make them thin wrappers. Similarly for
_store.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>

Asus Zenbook ux31a is providing ACPI0008 interface for ALS
(Ambient Light Sensor), which is accessible for OS => Win 7.
This sensor can be used with iio/acpi-als driver.
Since it is disabled by default, we should use asus-wmi
interface to enable it.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>

My patch to the ideapad-laptop driver to get the ESC key working on the
Yoga 1170 (Yoga 3) failed to do the same for the following model, the
Lenovo Yoga 700.

Denis Gordienko managed to get it working by adding another GUID for the
new WMI interface. I have adapted his patch to normal coding style
and simplified it a bit for inclusion, but this patch is currently
untested.

Link: https://forums.lenovo.com/t5/Lenovo-Yoga-Series-Notebooks/YOGA-3-14-How-to-reclaim-my-Esc-key-and-permanently-disable/m-p/3317499Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NDenis Gordienko <denis.gordienko.mail@gmail.com>
[dvhart: Whitespace cleanup, static const char *const array declaration]
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>

Microsoft Surface Book has a tablet mode button. Print another message
once on this event instead of repeating "Unknown event...".

Unfortunately, proper support involves the _DSM method, which is not a
discoverable interface. Just print a warning for now.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>