Hauppauge HVR-955Q is a ATSC/QAM USB tuner with LGDT3306A demodulator and SiLabs Si2157-A30 tuner.

Only digital TV has been tested (both ATSC and QAM256).
Signed-off-by: NOlli Salonen <olli.salonen@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

drivers/media/usb/cx231xx/cx231xx-cards.c: In function ‘cx231xx_usb_probe’:
drivers/media/usb/cx231xx/cx231xx-cards.c:1589:15: error: ‘struct v4l2_device’ has no member named ‘mdev’
  dev->v4l2_dev.mdev = dev->media_dev;
               ^
drivers/media/usb/cx231xx/cx231xx-cards.c:1589:26: error: ‘struct cx231xx’ has no member named ‘media_dev’
  dev->v4l2_dev.mdev = dev->media_dev;
                          ^
scripts/Makefile.build:257: recipe for target 'drivers/media/usb/cx231xx/cx231xx-cards.o' failed
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Now that we have entities and pads, let's create media links
between them, for analog setup.

We may not have all the links for digital yet, as the dvb extention
may not be loaded yet.
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Let's add media controller support for this driver and register it
for both V4L and DVB.

The media controller on this driver is not mandatory, as it can fully
work without it. So, if the media controller register fails, just print
an error message, but proceed with device registering.
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

changeset 5eeb3014 added a fixup at the error check
code. However, it introduced a new error:

	drivers/media/usb/cx231xx/cx231xx-cards.c:1586 cx231xx_usb_probe() error: we previously assumed 'dev' could be null (see line 1430)

This happens when dev = kmalloc() fails. So, instead of relying
on it to succeed, just change the parameter of clear_bit() from
'dev->devno' to 'nr'.

Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Commit b7085c08 ("cx231xx: convert from pr_foo to dev_foo")
moves usb_get_dev(interface_to_usbdev(interface)) to the beginning
of cx231xx_usb_probe() to use udev->dev in dev_err(),
but it does not make sure usbdev is put on all failure paths.

Later dev_err(udev->dev) was replaced by dev_err(d).
So the patch moves usb_get_dev() below (before the first use)
and fixes another failure path.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Unfortunately, on devices that have multiple interfaces, udev->dev
points to the parent device (usb) instead of the cx231xx specific one.

Due to that the logs don't look too nice, as they'll print messages
as if they were produced by USB core:
  usb-1-2: New device Conexant Corporation Polaris AV Capturb @ 480 Mbps (1554:5010) with 7 interfaces

Instead of using the name of the parent device, let's use the name
of the first cx231xx interface for all cx231xx sub-modules.

With this path, the logs will be nicer:

  cx231xx 1-2:1.1: New device Conexant Corporation Polaris AV Capturb @ 480 Mbps (1554:5010) with 7 interfaces
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

There are several places at cx231xx that uses printk without
any special reason. Change all of them to use dev_foo().
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Replace all pr_foo occurrences by dev_foo, as this is
the recommended way for drivers.
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

There are lots of debug printks printed with pr_info. Also, the
printk's data are not too coherent:

- there are duplicated driver name at the print format;
- function name format string differs from function to function;
- long strings broken into multiple lines;
- some printks just produce ugly reports, being almost useless
  as-is.

Do a cleanup on that.

Still, there are much to be done in order to do a better printk
job on this driver, but, at least it will now be a way less
verbose, if debug printks are disabled, and some logs might
actually be useful.
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

It currently does just like what pr_foo() macros do. So,
replace them.

A deeper cleanup is needed, as there are lots of debug macros
printed with pr_info.
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

All switching should be done by i2c mux adapters.
Drop explicit dont_use_port_3 flag.
Drop info message about switch.

Only the removed code in start_streaming is questionable:
It did switch the port_3 flag without accessing i2c in between.
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

change almost all instances of I2C_1 to I2C_1_MUX_3

Only these cases are changed to I2C_1_MUX_1:
* All that have dont_use_port_3 set.
* CX231XX_BOARD_HAUPPAUGE_EXETER, old code did explicitly not switch to port3.
* eeprom access for 930C
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This is a preparation for mapping I2C_1_MUX_1 and I2C_1_MUX_3 later to the seperate
muxed i2c adapters.

Map mux adapters to I2C_1 for now.

Add local variables for i2c_adapters in dvb_init to get line lengths
shorter.
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Replace numbers by the constants of same value and same meaning.
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This is a preparation for deleting the otherwise useless i2c_clients
that are allocated for all the i2c master adapters.
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Add support for:
	[2040:b139] Hauppauge WinTV HVR-901H (1114xx)

According to the inf file, the hardware is similar to [2040:b131] Hauppauge WinTV 930C-HD (model 1114xx)
The only difference is the demod Si2161 instead of Si2165 (but both are
supported by the si2165 driver).
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Add support for:
	[2040:b138] Hauppauge WinTV HVR-900H (111xxx)

The hardware is similar to [2040:b130] Hauppauge WinTV 930C-HD (model 1113xx)
The only difference is the demod Si2161 instead of Si2165 (but both are
supported by the si2165 driver).
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Fix the following warnings:
	drivers/media/usb/cx231xx/cx231xx-cards.c: In function 'read_eeprom':
	drivers/media/usb/cx231xx/cx231xx-cards.c:979:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for:
	[2013:025e] PCTV QuatroStick 522e

The hardware is identical to Hauppauge WinTV 930C-HD (model 1114xx)
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for:
	[2013:0259] PCTV QuatroStick 521e

The hardware is identical to Hauppauge WinTV 930C-HD (model 1113xx)
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for:
	[2040:b131] Hauppauge WinTV 930C-HD (model 1114xx)
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Tested-by: NMauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for:
	[2040:b130] Hauppauge WinTV 930C-HD (model 1113xx)

After loading the driver the first open to dvb device node fails.
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Instead of using some random value, return an error if the
PCB config is not available or doesn't match a know profile
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

That makes easier to understand the code. It would also help
to add support for having boards with just digital support
on some latter patch, as allowed by some PCB configs.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The initialization is already too complex. Use devm_ functions
to make the code simpler and easier to modify.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

On some newer boards, like HVR-930C HD, the information at
the PCB tables are sometimes higher than the ones actually
available on the device. That causes the probing code to
go past the interfaces array.

Add checks to the interface number before going past the
array.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The max number of interfaces was read from the wrong descriptor.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add a new USB ID to the driver.
Signed-off-by: NLinks (Markus) <help.markus+git@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

We dereference "dev" after it has already been freed.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

There are numerous issues in error handling code of cx231xx initialization.
Double free (when cx231xx_init_dev() calls kfree(dev) via cx231xx_release_resources()
and then cx231xx_usb_probe() does the same) and memory leaks
(e.g. usb_get_dev() before (ifnum != 1) check in cx231xx_usb_probe())
are just a few of them.
The patch fixes the issues in cx231xx_usb_probe() and cx231xx_init_dev()
by moving usb_get_dev(interface_to_usbdev(interface)) below in code and
implementing proper error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The KWorld UB445-U is similar to the UB430-AF but with a Samsung S5H1411
frontend. Luckily all of the hardware is already well supported, just the
device and USB ids need to be added to get it to work.
Signed-off-by: NJohannes Erdfelt <johannes@erdfelt.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Remove g_chip_ident and replace it with g_chip_info.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Thanks for the response, I have done as you suggested.
Below is an updated patch for the OTG102 device against http://git.linuxtv.org/hverkuil/media_tree.git/shortlog/refs/heads/cx231xx, kernel version 3.8.
With further testing it appears the extra clauses in cx231xx-cards.c were not necessary (in static in cx231xx_init_dev and static int cx231xx_usb_probe), so those have been also been removed.
Signed-off-by: NMatt Gomboc <gomboc0@gmail.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Tested on my big-endian ppc-based test machine.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It's not working reliably if port 3 is enabled.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The 417 support doesn't work. Until someone can dig into this driver to
figure out why it isn't working the 417 support is disabled.
Sometimes you can actually stream a bit, but very soon the whole machine
crashes, so something is seriously wrong.
For the record, this was not introduced by my recent changes to this driver,
it was broken before that.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is needed to resolve the v4l2-compliance complaints about the control
ioctls.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This kind of memcpy() is error-prone. Its replacement with a struct
assignment is prefered because it's type-safe and much easier to read.
Found by coccinelle. Hand patched and reviewed.
Tested by compilation only.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier struct_name;
struct struct_name to;
struct struct_name from;
expression E;
@@
-memcpy(&(to), &(from), E);
+to = from;
// </smpl>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds support for the Elgato Video Capture, version 2, device.
The device is added based on the code for CX231XX_BOARD_HAUPPAUGE_USBLIVE2,
it is simply a copy of the code for that board, with the proper USB device
info for the Elgato Video Capture V2 device.
Signed-off-by: NAlf Høgemark <alf@i100.no>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>