The Denali controller can also be found in SoC devices attached to a
simple bus.  Move the PCI specific parts into denali_pci so that we can
add a denali_dt that uses the same driver but for a device tree driver
instead of a PCI based device.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

There is an implemention of hardware ECC write page function which may return an
error indication.
For instance, using Atmel HW PMECC to write one page into a nand flash, the hardware
engine will compute the BCH ecc code for this page. so we need read a the
status register to theck whether the ecc code is generated.
But we cannot assume the status register always can be ready, for example,
incorrect hardware configuration or hardware issue, in such case we need
write_page() to return a error code.

Since the definition of 'write_page' function in struct nand_ecc_ctrl is 'void'.
So this patch will:
  1. add return 'int' value for 'write_page' function.
  2. to be consitent, add return 'int' value for 'write_page_raw' fuctions too.
  3. add code to test the return value, and if negative, indicate an
  error happend when write page with ECC.
  4. fix the compile warning in all impacted nand flash driver.

Note: I couldn't compile-test all of these easily, as some had ARCH dependencies.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

As of [mtd: nand: remove autoincrement 'sndcmd' code], the
NAND_CMD_READ0 command is issued unconditionally.

Thus, read_oob/read_oob_raw's 'sndcmd' argument is no longer needed, as
well as their return code.

Remove the 'sndcmd' parameter, and set the return code to 0.
Signed-off-by: NShmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

New NAND controllers can perform read/write via HW engines which don't expose
OOB data in their DMA mode. To reflect this, we should rework the nand_chip /
nand_ecc_ctrl interfaces that assume that drivers will always read/write OOB
data in the nand_chip.oob_poi buffer. A better interface includes a boolean
argument that explicitly tells the callee when OOB data is requested by the
calling layer (for reading/writing to/from nand_chip.oob_poi).

This patch adds the 'oob_required' parameter to each relevant {read,write}_page
interface; all 'oob_required' parameters are left unused for now. The next
patch will set the parameter properly in the nand_base.c callers, and follow-up
patches will make use of 'oob_required' in some of the callee functions.

Note that currently, there is no harm in ignoring the 'oob_required' parameter
and *always* utilizing nand_chip.oob_poi, but there can be
performance/complexity/design benefits from avoiding filling oob_poi in the
common case. I will try to implement this for some drivers which can be ported
easily.

Note: I couldn't compile-test all of these easily, as some had ARCH
dependencies.

[dwmw2: Merge later 1/0 vs. true/false cleanup]
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Reviewed-by: NShmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: NJiandong Zheng <jdzheng@broadcom.com>
Acked-by: NMike Dunn <mikedunn@newsguy.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The ecc.read_page() method for nand drivers is changed to return the maximum
number of bitflips that were corrected on any one region covering an ecc step,
This patch doesn't change what the nand code returns to mtd.

This v2 includes the change to the fsl_ifc_nand driver requested by Scott¹.

¹ http://lists.infradead.org/pipermail/linux-mtd/2012-April/040883.htmlSigned-off-by: NMike Dunn <mikedunn@newsguy.com>
Acked-by (freescale changes): Scott Wood <scottwood@freescale.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch converts the drivers in drivers/mtd/* to use module_pci_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Flash device drivers initialize 'ecc_strength' in struct mtd_info, which is the
maximum number of bit errors that can be corrected in one writesize region.

Drivers using the nand interface intitialize 'strength' in struct nand_ecc_ctrl,
which is the maximum number of bit errors that can be corrected in one ecc step.
Nand infrastructure code translates this to 'ecc_strength'.

Also for nand drivers, the nand infrastructure code sets ecc.strength for ecc
modes NAND_ECC_SOFT, NAND_ECC_SOFT_BCH, and NAND_ECC_NONE.  It is set in the
driver for all other modes.
Signed-off-by: NMike Dunn <mikedunn@newsguy.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Commit c89eeda8 (mtd: denali: detect the
number of banks) introduced runtime detection of the number of banks.

However, denali_nand_reset() uses uses denanli_nand_info::max_banks so
we need to detect the maximum number of banks before doing the reset.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>

The implementation of nand_release() already call mtd_device_unregister(),
no need to call it again.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>

Recall the recently added prefix requirements:
 * "NAND_" for flags in nand.h, used in nand_chip.options
 * "NAND_BBT_" for flags in bbm.h, used in nand_chip.bbt_options
        or in nand_bbt_descr.options

Thus, I am changing NAND_USE_FLASH_BBT to NAND_BBT_USE_FLASH.

Again, this flag is found in bbm.h and so should NOT be used in the
"nand_chip.options" field.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>

This patch works with the following three flags from two headers (nand.h
and bbm.h):
  (1) NAND_USE_FLASH_BBT (nand.h)
  (2) NAND_USE_FLASH_BBT_NO_OOB (nand.h)
  (3) NAND_BBT_NO_OOB (bbm.h)

These flags are all related and interdependent, yet they were in
different headers. Flag (2) is simply the combination of (1) and (3) and
can be eliminated.

This patch accomplishes the following:
  * eliminate NAND_USE_FLASH_BBT_NO_OOB (i.e., flag (2))
  * move NAND_USE_FLASH_BBT (i.e., flag (1)) to bbm.h

It's important to note that because (1) and (3) are now both found in
bbm.h, they should NOT be used in the "nand_chip.options" field.

I removed a small section from the mtdnand DocBook because it referes to
NAND_USE_FLASH_BBT in nand.h, which has been moved to bbm.h.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>

The older add_mtd_device()/add_mtd_partitions() and their removal
counterparts will soon be gone.  Replace uses with mtd_device_register()
and mtd_device_unregister().
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Not all configurations of the Denali controller support 4 banks.  The
controller can support between 1 and 16 banks.  Detect this from the
design features register.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The controller has interrupt enable/status register pairs for each bank
(along with ECC and status registers) that differ only in address offset.
Rather than providing definitions for each register, make the address a
macro so that it scales for devices with different numbers of banks.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Rather than using the PCI specific DMA API, convert to the generic
DMA API so that we can use the Denali NAND controller on other bus
types.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The kernel already prints its build timestamp during boot, no need to
repeat it in random drivers and produce different object files each
time.
Signed-off-by: NMichal Marek <mmarek@suse.cz>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

Signed-off-by: NFlorian Fainelli <ffainelli@freebox.fr>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

All hardware initialization will be done in denali_hw_init before
irq handler registered
Change mtd name from "DENALI NAND" to be "denali-nand" since whitespace in
name can cause problems if we use cmdlinepart
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

In mtd->write, Denali controller will use MODE_11 mode to read
NAND flash status, then return back to MODE_1O mode to do page
write.
Here comes a bug for this kind of using, sometimes controller will
not write data to NAND and just return a good interrupt to tell
driver writing work is done. The data in this page is all 0xff and
this page can not be written again. The reason is unknow.

So read Denali controller register WRITE_PROTECT to get NAND status
instead.
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

waring: no space for starting a line
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Once the last ECC error was handled, controller will triger an
interrupt. If this interrupt can not be clean on time, controller
may corrupt.
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

denali_write32() just implements a debug function for iowrite32(),
only print out the write value. Remove this function since it's useless
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Fixed a pci_resource_len function error;
Changed returning sequence of probe function;
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

set_ecc_config function only set ECC_CORRECTION register, so
move register setting to probe function.
Since controller only support 15bit and 8bit ecc correction,
updated nand ecc layout information.
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Hi David,
   I sent 4 patches using my intel email account. If there is any
   problem about the format of these patches, I will resend them after
   I arrived at home by using my gmail account, and I will keep on
   using gmail account to send patches.
   Thanks.

>From 242e3bf5e17f54b1df8cf285154a7c7a61ff62e9 Mon Sep 17 00:00:00 2001
From: Chuanxiao Dong <chuanxiao.dong@intel.com>
Date: Fri, 6 Aug 2010 15:29:41 +0800
Subject: [PATCH 1/4] mtd: denali: Remove device_info_tag structure.

Most of the variables in this structure are useless, so just
remove this structure and relevant codes.
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

In denali driver, wTotalBlocks variable is useless, so just
remove them in get_toshiba_nand_para and get_hynix_nand_para
first. Other wTotalBlocks in denali.c and other variables in
dev_info struct are also useless, will remove them later.

Also add a parameter in get_hynix_nand_para to prepare to
remove dev_info struct. This parameter comes by reading NAND
ID directly. Reading register will report wrong value for
some NAND chips, e.g. some Micron MT29F32G08QAA chips.
So update NAND_CMD_READID method as well.
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

rename these functions' name and remove additional declarations
in header file
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Hi,
I have changed the outlook mail cliet to be linux mutt client and use my
personal gmail to submit patches.
Here are 5 new patches to fix nand/denali check patch errors. The other
4 patches will be sent out after this mail.
Thanks for your review.

>From d125ad3f57bbf517131dccad6b5933edf8c2632a Mon Sep 17 00:00:00 2001
From: Chuanxiao Dong <chuanxiao.dong@intel.com>
Date: Tue, 3 Aug 2010 15:54:48 +0800
Subject: [PATCH 1/5] mtd: denali.c: clean up all whitespaces in code indent
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>