- 10 11月, 2007 1 次提交
-
-
由 Marcelo Tosatti 提交于
Properly account for queue commands, this fixes a problem reported by Holger Schurig when using the debugfs interface. Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 11 10月, 2007 20 次提交
-
-
由 Holger Schurig 提交于
Don't write constants that are (per documentation and struct) u8 as 0x0001, use 0x01 instead. Also remove an useless cast. Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Acked-By: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Pierre Ossman 提交于
Make sure that errors reported by the hardware layer is properly handled. Otherwise commands tend to get stuck in limbo. Signed-off-by: NPierre Ossman <drzeus@drzeus.cx> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Luis Carlos Cobo 提交于
Boot2 version used to be hardcoded in the uploaded firmware, this patch preserves the boot2 version before uploading firmware and sends it to the firmware again on resume. Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Eugene Teo 提交于
adapter is NULL if cmdnode is not. Signed-off-by: NEugene Teo <eugeneteo@kernel.sg> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Williams 提交于
keytype is a u8 Signed-off-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Luis Carlos Cobo 提交于
Driver support for the monitor mode support that will be available in the next OLPC 'bleeding edge' Marvell firmware release (most likely, 5.110.16.p2). To activate monitor mode, echo mode > /sys/class/net/{ethX,mshX}/device/libertas_rtap where mode is the hex mask that specifies which frames to sniff (in short, 0x1 for data, 0x2 for all management but beacons, 0x4 for beacons). Any non zero mode will activate the monitor mode, inhibiting transmission in ethX and mshX interfaces and routing all the incoming traffic to a new rtapX interface that will output the packets in 802.11+radiotap headers format. Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
multipledtim was initialized with MRVDRV_DEFAULT_MULTIPLE_DTIM and then kept at that value, so we could use that define directly. Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
locallisteninterval was initialized with 0, but there is no code that changes it, rendering it rather useless. Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
No code ever initialized this variable, so it was 0 because of kzalloc(). But no other code changes it, making it rather useless. Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
Those two variables were initialized with some default values, but there is no code that would ever change them. So we could use as well the defaults directly. Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
The value of txrate was only set by a CMD_802_11_TX_RATE_QUERY command, but there was no code in the driver that ever issued this command. Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
There was nowhere any code that used the values of those variables. This patch also removes two static functions that are now unused. Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
... and LBS_DEB_CMD for command execution. Also tidies misc comments to give a consistent output. Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
Currently, when you define LBS_DEB_HEX, you get every hex dump in the whole driver, e.g. for LBS_DEB_CMD, LBS_DEB_RX, LBS_DEB_TX etc. This patch makes sure that you only get the hexdump that you're interested in. Renamed lbs_dbg_hex() into lbs_deb_hex(), like the other lbs_deb_XXX() macros. Made lbs_deb_hex() issue a line feed (and a new prompt) after 16 bytes. As lbs_deb_hex() now prints the ":" after the prompt by itself, removed the misc colons in the various *.c files. lbs_deb_XXX() now print the debug category as well. As lbs_deb_XXX() --- and especially lbs_deb_11d() --- now print the category, I removed various "11D:" prefixes in 11d.c as well. Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
Some functions where declared in header files, but used only once. They are now static functions. After doing this, I found out that some functions weren't used at all. I removed this dead code. Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Williams 提交于
Remove unused/duplicated fields and consolidate static data rate arrays, for example the libertas_supported_rates[] and datarates[] arrays in the bss_descriptor structure, and the libertas_supported_rates field in the wlan_adapter structure. Introduce libertas_fw_index_to_data_rate and libertas_data_rate_to_fw_index functions and use them everywhere firmware requires a rate index rather than a rate array. The firmware requires the 4 basic rates to have the MSB set, but most other stuff doesn't, like WEXT and mesh ioctls. Therefore, only set the MSB on basic rates when pushing rate arrays to firmware instead of doing a ton of (rate & 0x7f) everywhere. Signed-off-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Williams 提交于
Mistakently introduced by a previous patch to upper-case all command constants. Signed-off-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Williams 提交于
Remove the thread.h abstractions and opencode kthread stuff to make it clearer. Signed-off-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Williams 提交于
For readability. Signed-off-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Williams 提交于
It doesn't touch hardware and therefore doesn't need endian notations either. Signed-off-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 11 7月, 2007 1 次提交
-
-
由 Dan Williams 提交于
Found by Guillaume LECERF <glecerf@gmail.com> Signed-off-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 28 6月, 2007 1 次提交
-
-
由 Dan Williams 提交于
Don't clobber the firmware's internal state machine by setting ENABLE_RSN more than once during the 4-way handshake. Check what the ENABLE_RSN status is and only set if it should be changed. Signed-off-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 12 6月, 2007 9 次提交
-
-
由 David Woodhouse 提交于
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Williams 提交于
Fix WPA so it works up through the supplicant 4-Way handshake process. Doesn't successfully pass traffic yet; may be problems installing the GTK to the firmware. - RSN needs to be enabled before the association command is sent - Use keys from the association request not the adapter structure - cmd_act_mac_strict_protection_enable != IW_AUTH_DROP_UNENCRYPTED - Fix network filtering logic in is_network_compatible() WPA helpers Signed-off-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Williams 提交于
Signed-off-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Luis Carlos Cobo 提交于
Updated commands fwt_add and fwt_list, bt_list. New commands: bt_get_invert, bt_set_invert, to invert the blinding table, i.e., receive only frames from nodes listed in the BT. This patch needs/is needed for firmware 5.220.9.p11. Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
Actually, this patch removev wlan_dev_t totally and puts the used variables of it directly into wlan_private. That reduces one level of indirection and looks a little bit simpler. It's now "priv->card" and not "priv->wlan_dev.card" and "priv->dev" instead of "priv->wlan_dev.netdev" Changed two occurences of "((wlan_private *) dev->priv)->wlan_dev.netdev" into "dev", because I didn't see the point in doing pointer-ping-pong. The variables "ioport", "upld_rcv" and "upld_type" where unused. They have been removed. Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
* add CONFIG_LIBERTAS to Kconfig * remove global variable libertas_fw_name, the USB module might want to use a different default FW name than the CF module, so libertas_fw_name is now local to if_usb.c * exported some symbols as GPL Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
This functions makes all libertas_sbi_XXX functions static to the if_usb.c file and renames them to if_usb_XXXX(). The get called from other places of the source code via priv->hw_XXXX(). Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
The subject says it all. Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
The debug output of libertas was either not present or it was overwhelming. This patch adds the possibility to specify a bitmask for the area of interest. One should then only get the desired output. Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 12 5月, 2007 2 次提交
-
-
由 Dan Williams 提交于
Signed-off-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Williams 提交于
Use standard IW_MODE_* constants instead. Signed-off-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 28 4月, 2007 1 次提交
-
-
由 Marcelo Tosatti 提交于
Add the Marvell Libertas 8388 802.11 USB driver. Signed-off-by: NMarcelo Tosatti <marcelo@kvack.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-