In ESA mode STCKF is not defined even if the facility bit is enabled.
To prevent an illegal operation we must also check if we run a 64 bit kernel.
To make the check perform well add the STCKF bit to the machine flags.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Split out addressing mode bits from PSW_BASE_BITS, rename PSW_BASE_BITS
to PSW_MASK_BASE, get rid of psw_user32_bits, remove unused function
enabled_wait(), introduce PSW_MASK_USER, and drop PSW_MASK_MERGE macros.
Change psw_kernel_bits / psw_user_bits to contain only the bits that
are always set in the respective mode.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

When IPL'ing from a block device and an NSS should be created we must
make sure that the kernel image and the initrd are in different 1MB
segments. Otherwise creating the NSS will fail.
So we make sure the initrd is 4MB behind the end of the kernel image
like we do already when IPL via the VM reader is performed.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Use snprintf() here as well so we won't have to deal with this again.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This patch fixed bugzilla #12965:
https://bugzilla.kernel.org/show_bug.cgi?id=12965

The original code contains some inproper use of sprintf
function where a buffer is used both as input string
as well as output string. It should remember the written
bytes in the previous and use that as the offset for
later writing. Also replace sprintf with snprintf.
Signed-off-by: NChen Liu <chenliu@asset.uwaterloo.ca>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

arch/s390/kernel/early.c: In function 'setup_hpage':
arch/s390/kernel/early.c:285:15: warning: unused variable 'facilities'
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Move cpu topology facility detection to early setup code where it
should be.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Store the facility list once at system startup with stfl/stfle and
reuse the result for all facility tests.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Improve performance of the sske operation by using the nonquiescing
variant if the affected page has no mappings established. On machines
with no support for the new sske variant the mask bit will be ignored.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Use the SPP instruction to set a tag on entry to / exit of the virtual
machine context. This allows the cpu measurement facility to distinguish
the samples from the host and the different guests.
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>

The savesys_ipl_nss asm function is put into the .init.text section
however it is missing a ".previous" section which would restore the
previous section.
Luckily all functions in early.c are init functions so it doesn't
matter currently.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Move the ebcdic to ascii conversion of the kernel parameter line from
head.S to early.c and convert the assembler code to C.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Introduce the MACHINE_IS_LPAR flag for code that should only be
executed if Linux is running in an LPAR.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

After an IPL from NSS the uptime of the system is incorrect. The reason
is that the startup code in head.S is not executed in case of an IPL
from NSS. Due to that sched_clock_base_cc which is used to initialze
wall_to_monotonic contains the time stamp when the NSS has been created
instead of the time stamp of the system start.

Reinitialize the cputime accounting values in create_kernel_nss after
the SAVESYS CP command that created the NSS segment.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

If a named saved system (NSS) cannot be defined or saved, print out an
error message with the return code of the underlying z/VM CP command.
Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Eleminate the local variable machine_flags and always change machine
flags directly in the lowcore.
This avoids confusion about when and why the two variables have to be
synchronized.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Append scpdata to the kernel boot command line. If scpdata starts
with the equal sign (=), the kernel boot command line is replaced.
(For consistency with zIPL and IPL PARM parameters.)

To use scpdata for the kernel boot command line, scpdata must consist
of ascii characters only. If scpdata contains other characters,
scpdata is not appended to the kernel boot command line.
In addition, re-IPL is extended for setting scpdata for the next
Linux reboot.
Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Currently, the machine_flags are stored late in the startup
initialization which results in failing machine type checks
(e.g. for MACHINE_IS_VM).
To allow these checks, store the machine flags in the lowcore
when the machine type has been detected.

Moving the machine_flags to the lowcore has been introduced with
git commit 25097bf1Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Our swsusp_arch_suspend() backend implementation disables prefixing
by setting the contents of the prefix register to 0.
However afterwards common code functions are called which might
access percpu data structures.
Since the lowcore contains e.g. the percpu base pointer this isn't
a good idea. So fix this by copying the hibernating cpu's lowcore to
absolute address zero.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This patch introduces the hibernation backend support to the
s390 architecture. Now it is possible to suspend a mainframe Linux
guest using the following command:

echo disk > /sys/power/state
Signed-off-by: NHans-Joachim Picht <hans@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Dynamic ftrace support for s390.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Add a read_persistent_clock function that does not just return 0.
Since timekeeping_init calls the function before time_init has been
called move reset_tod_clock to early.c to make sure that the TOD
clock is running when read_persistent_clock is invoked.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Currently the storage of the machine flags is a globally exported unsigned
long long variable. By moving the storage location into the lowcore struct we
allow assembler code to check machine_flags directly even without needing a
register. Addtionally the lowcore and therefore the machine flags too will be
in cache most of the time.
Signed-off-by: NChristian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

strlcpy() does already NUL-terminate the destination string.
Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Currently we use the cpuid (via STIDP instruction) to recognize LPAR,
z/VM and KVM.
The architecture states, that bit 0-7 of STIDP returns all zero, and
if STIDP is executed in a virtual machine, the VM operating system
will replace bits 0-7 with FF.

KVM should not use FE to distinguish z/VM from KVM for interested
guests. The proper way to detect the hypervisor is the STSI (Store
System Information) instruction, which return information about the
hypervisors via function code 3, selector1=2, selector2=2.

This patch changes the detection routine of Linux to use STSI instead
of STIDP. This detection is earlier than bootmem, we have to use a
static buffer. Since STSI expects a 4kb block (4kb aligned) this
patch also changes the init.data alignment for s390. As this section
will be freed during boot, this should be no problem.

Patch is tested with LPAR, z/VM, KVM on LPAR, and KVM under z/VM.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Most likely it is broken anyway because of the changes in memory
detection. Since we can't test it and there are probably better ways
that using a P390 card, remove support for it.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Move memory detection code to own file and also simplify it.
Also add an interface which can be called at any time to get the
current memory layout. This interface is needed by our kernel
internal system dumper.

Cc: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Cc: Michael Holzheu <holzheu@de.ibm.com>
Cc: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Now it is possible to specify additional kernel parameters on the IPL
command line using the IPL PARM option.
If the Linux system is already running, the new reipl sysfs attribute
'parm' can be used to change kernel parameters for the next reboot.
Examples:
  IPL    C PARM dasd=1234 root=/dev/dasda1
  IPL 1234 PARM savesys=mylnxnss
  echo "init=/bin/bash" > /sys/firmware/reipl/ccw/parm
Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

In case the initrd is located within the bss section it will be
overwritten when the section is cleared. To prevent this just move
the initrd right behind the bss section if it starts within the
section.
The current code already moves the initrd if the bootmem allocator
bitmap would overwrite it. With this patch we should be safe against
initrd corruptions.

Cc: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This adds hugetlbfs support on System z, using both hardware large page
support if available and software large page emulation on older hardware.
Shared (large) page tables are implemented in software emulation mode,
by using page->index of the first tail page from a compound large page
to store page table information.
Signed-off-by: NGerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

From: Heiko Carstens <heiko.carstens@de.ibm.com>
From: Carsten Otte <cotte@de.ibm.com>

This lets us use defines for the magic bits in machine flags instead
of using plain numbers all over the place.
In addition on newer machines features/facilities are indicated by the
result of the stfl instruction. So we use these bits instead of trying
to execute new instructions and check wether we get an exception or
not.
Also the mvpg instruction is always available when in zArch mode,
whereas the idte instruction is only available in zArch mode. This
results in some minor optimizations.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This patch adds functionality to detect if the kernel runs under the KVM
hypervisor. A macro MACHINE_IS_KVM is exported for device drivers. This
allows drivers to skip device detection if the systems runs non-virtualized.
We also define a preferred console to avoid having the ttyS0, which is a line
mode only console.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Acked-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

Most noteable part of this commit is the new local header file entry.h
which contains all the function declarations of functions that get only
called from asm code or are arch internal. That way we can avoid extern
declarations in C files.
This is more or less the same that was done for sparc64.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

/sys/firmware/reipl/nss/name contains the nss name when defsys or
savesys command has been executed. If the defsys or savesys command
fails the kernel_nss_name has to be cleared since a reipl on that
nss name won't be possible.
Signed-off-by: NHongjie Yang <hongjie@us.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

It caused only a lot of confusion. From now on cpu hotplug of up to
NR_CPUS will work by default. If somebody wants to limit that then
the possible_cpus parameter can be used.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Add a new interface so that cpus can be put into standby state and
configured state.
Only offline cpus can be put into standby state or configured state.
For that the new percpu sysfs attribute "configure" must be used.
To put a cpu in standby state a "0" must be written to the attribute.
In order to switch it into configured state a "1" must be written to
the attribute.
Only cpus in configured state can be brought online.
In addition this patch introduces a static mapping of physical to
logical cpus. As a result only the sysfs directories of present cpus
will be created. To scan for new cpus the new sysfs attribute "rescan"
must be used.
Writing to /sys/devices/system/cpu/rescan will trigger a rescan of
cpus and will create directories for new cpus.

On IPL only configured cpus will be used. And on reboot/shutdown all
cpus will remain in their current state (configured/standby).
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Before we're getting short on memory detection fixes here is the next
one: if neither sclp nor diag260 report the storage size the detection
loop will return immediately without detecting anything. Fix this by
breaking the detection loop only if the memory end is known.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Yet another patch in the countless series of memory detection fixes:
if the last area of the reported storage size is a hole the detection
loop will loop forever.
Just break chunk detection loop if its end is going to be larger than
reported storage size.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Check if a command is available before executing. Saves some
superfluous service calls that won't succeed anyway.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Introduce some new interfaces so that random subsystems don't have to
mess around with sclp internal structures.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>