INCOstartec LILLY-DBB056 is a carrier board (baseboard) for
computer-on-module LILLY-A83X.

This patch adds device-tree support for most of its features.
Signed-off-by: NChristoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

INCOstartec LILLY-A83X module is a TI DM3730xx100 (OMAP3) SoC
computer-on-module.

This patch adds device tree support for most of its features.
Signed-off-by: NChristoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The clock for audio is sourced from virt_24000000_ck, so the correct
frequency is 24000000.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
CC: <stable@vger.kernel.org> # 3.13.x
Signed-off-by: NTony Lindgren <tony@atomide.com>

In omap2420.dtsi and omap2430.dtsi disable all mcbsp nodes and board dts
files can explicitly enable the mcbsp they are using.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

In omap3.dtsi disable all mcbsp nodes and board dts files can explicitly
enable the mcbsp they are using.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Board dts files will need to enable the IP nodes which they are using and
does not have to care about the not used ones (to disable them).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

All audio nodes has been set to disabled state in omap4.dtsi file.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

All audio nodes has been set to disabled state in omap4.dtsi file.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Board dts files will need to enable the IP nodes which they are using and
does not have to care about the not used ones (to disable them).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Attach the pinctrl nodes to their respective device node:
mcbsp1, mcbsp2, dmic, mcpdm and twl6040.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Attach the pinctrl nodes to their respective device node:
mcbsp1, mcpdm and twl6040.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add the hwspinlock device tree node for AM43xx family
of SoCs.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add the hwspinlock device tree node for DRA7 SoCs.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add a new generic property "#hwlock-cells" to the hwspinlock
DT nodes on OMAP4, OMAP5 and AM33xx. This common property allows
different platform implementations to define the args specifier
length. OMAP implementations will always use a value of 1.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

sbc-t3x boards features two external USB ports on SB-T35 baseboard.
The baseboardi USB hub reset signal should be de-asserted to make
those ports functional.

sbc-t3517 features additional (assembled on CoM) USB hub which also
requires reset signal handling.

Add quirks code to handle proper reset pulse signal.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for CM-T3517 CoM and SBC-T3517 board.

reused common support for sbc-t3x boards
(omap3-cm-t3x.dtsi, omap3-sb-t35.dtsi):

* SB-T35 baseboard eth
* MMC1, UART3
* HS USB Port 1/2
* I2C1/3
* Heartbit led

Added basic support for:

* MMC1 wp/cd signals
* CM-T3517 Usb Hub
* WL12xx WiFi chip
* Davinci EMAC
* AM35X OTG
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for CM-T3530 CoM and SBC-T3530 board.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add USB OTG support for cm-t3x30 CoMs.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPIO167 is used as SB-T35 baseboard USB Hub reset.
Add GPIO167 pinmux.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add HS USB Host support along with USB PHYs and power supply regulators
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add pullup for twl4030 GPIO_0 used as MMC1 card detect signal.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPIO186 is used for the heartbeat led.
Setup the pinmux for the GPIO186.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

SB-T35 baseboard features SMSC9220 Ethernet chip which requires
its own power supply regulators.

Add baseboard specific regulators for the SB-T35 Ethernet chip.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Disable mmc3 interface, since is not used on sbc-t3x boards.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Refactor the sbc-t3x device tree as a preparation for additional
(sbc-t3530, sbc-t3517, etc.) boards support.

No functional changes.

The device tree will have the following structure:

omap3-cm-t3x.dtsi
 |
 |<-- omap3-cm-t3x30.dtsi
 |     |
 |     |
 |     |     -----                  -------          ------------
 |     |    | CoM |                | Board |        | Base board |
 |     |     -----                  -------          ------------
 |     |                                            omap3-sb-t35.dtsi
 |     |                                                  |
 |     |<-- omap3-cm-t3730.dts <-- omap3-sbc-t3730.dts -->|
 |     |                                                  |
 |     |<-- omap3-cm-t3530.dts <-- omap3-sbc-t3530.dts -->|
 |                                                        |
 |<-------- omap3-cm-t3517.dts <-- omap3-sbc-t3517.dts -->|
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use omap specific pinctrl defines (OMAP3_CORE1_IOPAD) to configure
the padconf register offset.

This simplify further support of CompuLab's boards based on omap36xx,
omap34xx and am35x.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

update aliases for the ssi clocks ssi_ssr_fck, ssi_sst_fck and ssi_ick
to make them consistent for omap34xx and omap36xx. This makes it
possible to reference the clocks from generic omap3 dts files.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds a devicetree node for the backup battery regulator.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for the flexible mmap memory layout (as described in
http://lwn.net/Articles/91829). This is especially very interesting on
parisc since we currently only support 32bit userspace (even with a
64bit Linux kernel).
Signed-off-by: NHelge Deller <deller@gmx.de>

On Linux, only parisc uses a different value for EWOULDBLOCK which
causes a lot of troubles for applications not checking for both values.
Since the hpux compat is long dead, make EWOULDBLOCK behave the same as
all other architectures.
Signed-off-by: NGuy Martin <gmsoft@tuxicoman.be>
Signed-off-by: NHelge Deller <deller@gmx.de>

The stat.h header file is exported to userspace. Some userspace
applications failed to compile due to missing/unknown types, so we
better convert it to use native types only (like it's done on other
architectures too).
Signed-off-by: NHelge Deller <deller@gmx.de>

Signed-off-by: NHelge Deller <deller@gmx.de>

This commit:
f8dae006: parisc: Ensure full cache coherency for kmap/kunmap
caused negative caching side-effects, e.g. hanging processes with expect and
too many inequivalent alias messages from flush_dcache_page() on Debian 5 systems.

This patch now partly reverts it and has been in production use on our debian buildd
makeservers since a week without any major problems.
Signed-off-by: NHelge Deller <deller@gmx.de>
Signed-off-by: NJohn David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: NHelge Deller <deller@gmx.de>

With commit d8d14bd0 ("fs/compat: fix lookup_dcookie() parameter
handling") I changed the type of the len parameter of the
lookup_dcookie() syscall.

However I missed that there was still a stale declaration in
arch/tile/..  which now causes a compile error on tile:

  In file included from fs/dcookies.c:28:0:
  include/linux/compat.h:425:17: error: conflicting types for 'compat_sys_lookup_dcookie'
  fs/dcookies.c:207:1: error: conflicting types for 'compat_sys_lookup_dcookie'

Simply remove the declaration in the tile architecture, which is only a
leftover from before the different compat lookup_dcookie() versions have
been merged.  The correct declaration is now in include/linux/compat.h

The build error was reported by Fenguang's build bot.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

TI_EDMA fell out of automatically selected options in the multi_v7
defconfig due to a select being removed from the davinci Kconfig entry. So
we need to re-enable explicitly to not regress some platforms.

The rest is just the result of running 'make multi_v7_defconfig + make
savedefconfig' to remove entries that are no longer needed due to changed
dependencies/selects or defaults.
Signed-off-by: NOlof Johansson <olof@lixom.net>

Recent boot farm testing has highlighted some issues with mvebu and
multiplatform kernels.  Increase the test coverage so we can discover
these issues earlier.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The board schematic states that the "SD_CARD_DET_N gets pulled to GND
when card is inserted" so the polarity has been updated to active low.

Polarity is now specified with a GPIO define instead of a magic number.
Signed-off-by: NTim Kryger <tim.kryger@linaro.org>
Reviewed-by: NMatt Porter <matt.porter@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Select CONFIG_AT803X_PHY so that we can boot hummingboard via NFS.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Drop automatic selection of TI_EDMA from Keystone Kconfig file,
as it produces build warning in case if CONFIG_DMADEVICES is not set:

warning: (ARCH_KEYSTONE) selects TI_EDMA which has unmet direct dependencies (DMADEVICES && (ARCH_DAVINCI || ARCH_OMAP || ARCH_KEYSTONE))

Instead enable TI EDMA support from defconfig.
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add nodes for the Arasan SDHCI controller to Zynq dts files.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>