提交 d234e423 编写于 作者: D Dmitry Lifshitz 提交者: Tony Lindgren

ARM: dts: sbc-t3x: refactor DT support

Refactor the sbc-t3x device tree as a preparation for additional
(sbc-t3530, sbc-t3517, etc.) boards support.

No functional changes.

The device tree will have the following structure:

omap3-cm-t3x.dtsi
 |
 |<-- omap3-cm-t3x30.dtsi
 |     |
 |     |
 |     |     -----                  -------          ------------
 |     |    | CoM |                | Board |        | Base board |
 |     |     -----                  -------          ------------
 |     |                                            omap3-sb-t35.dtsi
 |     |                                                  |
 |     |<-- omap3-cm-t3730.dts <-- omap3-sbc-t3730.dts -->|
 |     |                                                  |
 |     |<-- omap3-cm-t3530.dts <-- omap3-sbc-t3530.dts -->|
 |                                                        |
 |<-------- omap3-cm-t3517.dts <-- omap3-sbc-t3517.dts -->|
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>
上级 fb5f895f
......@@ -32,16 +32,6 @@
};
&omap3_pmx_core {
mmc1_pins: pinmux_mmc1_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT_PULLUP | MUX_MODE0)/* sdmmc1_clk.sdmmc1_clk */
OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
>;
};
mmc2_pins: pinmux_mmc2_pins {
pinctrl-single,pins = <
......@@ -54,20 +44,6 @@
>;
};
smsc1_pins: pinmux_smsc1_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs5.gpmc_ncs5 */
OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLUP | MUX_MODE4) /* uart3_cts_rctx.gpio_163 */
>;
};
uart3_pins: pinmux_uart3_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
>;
};
wl12xx_gpio: pinmux_wl12xx_gpio {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE4) /* dss_data3.gpio_73 */
......@@ -76,13 +52,6 @@
};
};
&mmc1 {
vmmc-supply = <&vmmc1>;
bus-width = <4>;
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
};
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
......@@ -92,13 +61,3 @@
bus-width = <4>;
cap-power-off-card;
};
&smsc1 {
pinctrl-names = "default";
pinctrl-0 = <&smsc1_pins>;
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
};
/*
* Common support for CompuLab CM-T3x CoMs
*/
/ {
memory {
device_type = "memory";
reg = <0x80000000 0x10000000>; /* 256 MB */
};
leds {
compatible = "gpio-leds";
ledb {
label = "cm-t3x:green";
gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>; /* gpio186 */
linux,default-trigger = "heartbeat";
};
};
};
&omap3_pmx_core {
uart3_pins: pinmux_uart3_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
>;
};
mmc1_pins: pinmux_mmc1_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
>;
};
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
};
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
bus-width = <4>;
};
&i2c1 {
clock-frequency = <400000>;
};
&i2c3 {
clock-frequency = <400000>;
};
/*
* Common support for CompuLab CM-T3530 and CM-T3730
* Common support for CompuLab CM-T3x30 CoMs
*/
/ {
memory {
device_type = "memory";
reg = <0x80000000 0x10000000>; /* 256 MB */
};
#include "omap3-cm-t3x.dtsi"
/ {
cpus {
cpu@0 {
cpu0-supply = <&vcc>;
};
};
leds {
compatible = "gpio-leds";
ledb {
label = "cm-t35:green";
gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>; /* gpio186 */
linux,default-trigger = "heartbeat";
};
};
vddvario: regulator-vddvario {
compatible = "regulator-fixed";
regulator-name = "vddvario";
......@@ -36,11 +24,23 @@
};
};
&omap3_pmx_core {
smsc1_pins: pinmux_smsc1_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs5.gpmc_ncs5 */
OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLUP | MUX_MODE4) /* uart3_cts_rctx.gpio_163 */
>;
};
};
&gpmc {
ranges = <5 0 0x2c000000 0x01000000>;
smsc1: ethernet@5,0 {
compatible = "smsc,lan9221", "smsc,lan9115";
pinctrl-names = "default";
pinctrl-0 = <&smsc1_pins>;
interrupt-parent = <&gpio6>;
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
reg = <5 0 0xff>;
......@@ -74,8 +74,6 @@
};
&i2c1 {
clock-frequency = <400000>;
twl: twl@48 {
reg = <0x48>;
interrupts = <7>; /* SYS_NIRQ cascaded to intc */
......@@ -86,8 +84,8 @@
#include "twl4030.dtsi"
#include "twl4030_omap3.dtsi"
&i2c3 {
clock-frequency = <400000>;
&mmc1 {
vmmc-supply = <&vmmc1>;
};
&twl_gpio {
......
......@@ -2,11 +2,22 @@
* Common support for CompuLab SB-T35 used on SBC-T3530, SBC-T3517 and SBC-T3730
*/
&omap3_pmx_core {
smsc2_pins: pinmux_smsc2_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x20b6, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs4.gpmc_ncs4 */
OMAP3_CORE1_IOPAD(0x20d2, PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_wait3.gpio_65 */
>;
};
};
&gpmc {
ranges = <4 0 0x2d000000 0x01000000>;
smsc2: ethernet@4,0 {
compatible = "smsc,lan9221", "smsc,lan9115";
pinctrl-names = "default";
pinctrl-0 = <&smsc2_pins>;
interrupt-parent = <&gpio3>;
interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
reg = <4 0 0xff>;
......
......@@ -14,17 +14,3 @@
ranges = <5 0 0x2c000000 0x01000000>,
<4 0 0x2d000000 0x01000000>;
};
&smsc2 {
pinctrl-names = "default";
pinctrl-0 = <&smsc2_pins>;
};
&omap3_pmx_core {
smsc2_pins: pinmux_smsc2_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x20b6, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs4.gpmc_ncs4 */
OMAP3_CORE1_IOPAD(0x20d2, PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_wait3.gpio_65 */
>;
};
};
......@@ -99,7 +99,7 @@ static int omap3_sbc_t3730_twl_callback(struct device *dev,
int res;
res = gpio_request_one(gpio + 2, GPIOF_OUT_INIT_HIGH,
"wlan rst");
"wlan pwr");
if (res)
return res;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册