Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

The EDGE Port module of some ColdFire parts using the intc-simr interrupt
controller provides support for 7 external interrupts. These interrupts
go off-chip (that is they are not for internal peripherals). They need
some special handling and have some extra setup registers. Add code to
support them.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The reality is that you do not need the abiltity to configure the
clock divider for ColdFire CPUs. It is a fixed ratio on any given
ColdFire family member. It is not the same for all ColdFire parts,
but it is always the same in a model range. So hard define the divider
for each supported ColdFire CPU type and remove the Kconfig option.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The ColdFire 5207 and 5208 CPUs have fixed peripheral addresses.
They do not use the setable peripheral address registers like the MBAR
and IPSBAR used on many other ColdFire parts. Don't use fake values
of MBAR and IPSBAR when using peripheral addresses for them, there
is no need to.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The PIT hardware timer module used in some ColdFire CPU's is not always
addressed relative to an IPSBAR register. Parts like the ColdFire 5207 and
5208 have fixed peripheral addresses. So lets not define the register
addresses of the PIT relative to an IPSBAR definition. Move the base
address definitions into the per-part headers. This is a lot more consistent
since all the other peripheral base addresses are defined in the per-part
header files already.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The version 2 ColdFire CPU based cores all contain a similar cache
controller unit. Create a set of bit flag definitions for the supporting
registers.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The ColdFire UART base addresses varies between the different ColdFire
family members. Instead of keeping the base addresses with the UART
definitions keep them with the other addresses definitions for each
ColdFire part.

The motivation for this move is so that when we add new ColdFire
part definitions, they are all in a single file (and we shouldn't
normally need to modify the UART definitions in mcfuart.h at all).
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The instruction timings of the ColdFire 54xx family parts are
different to other version 4 parts (or version 2 or 3 parts for
that matter too).

Move the instruction timing setting into the ColdFire part
specific headers, and set the 54xx value appropriately.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Move the ColdFire CPU names out of setup.c and into their repsective
headers. That way when we add new ones we won't need to modify
setup.c any more.

Add the missing 548x CPU name.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Since Grant has added the coldfire-qspi driver to next-spi, here is the
platform support for the parts that have qspi hardware.  This sets up
gpio to do the spi chip select using the default chip select pins; it should
be trivial for boards that require different or additional spi chip selects to
use other gpios as needed.
Signed-off-by: NSteven King <sfking@fdwdc.com>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

With proper interrupt controller code in place there is no need for
devices like the timers to have custom interrupt masking code.
Remove it (and the defines that go along with it).
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The ColdFire 532x family of parts uses 2 of the same INTC interrupt
controlers used in the ColdFire 520x family. So modify the code to
support both parts. The extra code for the second INTC controler in
the case of the 520x is easily optimized away to nothing.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Create general interrupt controller code for the ColdFire 520x family,
that does proper masking and unmasking of interrupts. With this in
place some of the driver hacks in place to support ColdFire interrupts
can finally go away.

Within the ColdFire family there is a variety of different interrupt
controllers in use. Some are used on multiple parts, some on only one.
There is quite some differences in some varients, so much so that
common code for all ColdFire parts would be impossible.

This commit introduces code to support one of the newer interrupt
controllers in the ColdFire 5208 and 5207 parts. It has very simple
mask and unmask operations, so is one of the easiest to support.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Add support for the 520x.
Signed-off-by: NSteven King <sfking@fdwdc.com>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Merge header files for m68k and m68knommu to the single location:

    arch/m68k/include/asm

The majority of this patch was the result of the
script that is included in the changelog below.

The script was originally written by Arnd Bergman and
exten by me to cover a few more files.

When the header files differed the script uses the following:

The original m68k file is named <file>_mm.h  [mm for memory manager]
The m68knommu file is named <file>_no.h [no for no memory manager]

The files uses the following include guard:

This include gaurd works as the m68knommu toolchain set
the __uClinux__ symbol - so this should work in userspace too.

Merging the header files for m68k and m68knommu exposes the
(unexpected?) ABI differences thus it is easier to actually
identify these and thus to fix them.

The commit has been build tested with both a m68k and
a m68knommu toolchain - with success.

The commit has also been tested with "make headers_check"
and this patch fixes make headers_check for m68knommu.

The script used:
TARGET=arch/m68k/include/asm
SOURCE=arch/m68knommu/include/asm

INCLUDE="cachectl.h errno.h fcntl.h hwtest.h ioctls.h ipcbuf.h \
linkage.h math-emu.h md.h mman.h movs.h msgbuf.h openprom.h \
oplib.h poll.h posix_types.h resource.h rtc.h sembuf.h shmbuf.h \
shm.h shmparam.h socket.h sockios.h spinlock.h statfs.h stat.h \
termbits.h termios.h tlb.h types.h user.h"

EQUAL="auxvec.h cputime.h device.h emergency-restart.h futex.h \
ioctl.h irq_regs.h kdebug.h local.h mutex.h percpu.h \
sections.h topology.h"

NOMUUFILES="anchor.h bootstd.h coldfire.h commproc.h dbg.h \
elia.h flat.h m5206sim.h m520xsim.h m523xsim.h m5249sim.h \
m5272sim.h m527xsim.h m528xsim.h m5307sim.h m532xsim.h \
m5407sim.h m68360_enet.h m68360.h m68360_pram.h m68360_quicc.h \
m68360_regs.h MC68328.h MC68332.h MC68EZ328.h MC68VZ328.h \
mcfcache.h mcfdma.h mcfmbus.h mcfne.h mcfpci.h mcfpit.h \
mcfsim.h mcfsmc.h mcftimer.h mcfuart.h mcfwdebug.h \
nettel.h quicc_simple.h smp.h"

FILES="atomic.h bitops.h bootinfo.h bug.h bugs.h byteorder.h cache.h \
cacheflush.h checksum.h current.h delay.h div64.h \
dma-mapping.h dma.h elf.h entry.h fb.h fpu.h hardirq.h hw_irq.h io.h \
irq.h kmap_types.h machdep.h mc146818rtc.h mmu.h mmu_context.h \
module.h page.h page_offset.h param.h pci.h pgalloc.h \
pgtable.h processor.h ptrace.h scatterlist.h segment.h \
setup.h sigcontext.h siginfo.h signal.h string.h system.h swab.h \
thread_info.h timex.h tlbflush.h traps.h uaccess.h ucontext.h \
unaligned.h unistd.h"

mergefile() {
	BASE=${1%.h}
	git mv ${SOURCE}/$1 ${TARGET}/${BASE}_no.h
	git mv ${TARGET}/$1 ${TARGET}/${BASE}_mm.h

cat << EOF > ${TARGET}/$1
EOF

	git add ${TARGET}/$1
}

set -e

mkdir -p ${TARGET}

git mv include/asm-m68k/* ${TARGET}
rmdir include/asm-m68k

git rm ${SOURCE}/Kbuild
for F in $INCLUDE $EQUAL; do
	git rm ${SOURCE}/$F
done

for F in $NOMUUFILES; do
	git mv ${SOURCE}/$F ${TARGET}/$F
done

for F in $FILES ; do
	mergefile $F
done

rmdir arch/m68knommu/include/asm
rmdir arch/m68knommu/include

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

With the current kbuild infrastructure in place no other changes
are required for this to work.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Here is a small patch to automatically detect the DRAM size on m520x.
It was generated against 2.6.17-uc0, and tested on an Intec 5208 dev board.

(This part of the patch if the memory register defines for the 520x
ColdFire CPU family - Greg).
Signed-off-by: NMichael Broughton <mbobowik@telusplanet.net>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Add support for the internal register map of the 5208 ColdFire fmaily.
Patch originally from Matt Wadell (from code originally written by
Mike Lavender).
Signed-off-by: NGreg Ungerer <gerg@uclinux.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>