m68knommu: remove interrupt masking from ColdFire pit timer

With proper interrupt controller code in place there is no need for
devices like the timers to have custom interrupt masking code.
Remove it (and the defines that go along with it).
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

arch/m68k/include/asm/m520xsim.h

@@ -124,10 +124,6 @@
 #define MCF_GPIO_PAR_FECI2C_PAR_SDA_URXD2   (0x02)
 #define MCF_GPIO_PAR_FECI2C_PAR_SCL_UTXD2   (0x04)
 
-#define ICR_INTRCONF		0x05
-#define MCFPIT_IMR		MCFINTC_IMRL
-#define MCFPIT_IMR_IBIT		(1 << MCFINT_PIT1)
-
 /*
  *  Reset Controll Unit.
  */

arch/m68k/include/asm/mcfsim.h

@@ -101,20 +101,6 @@
 #endif
 
 
-/*
- *	PIT interrupt settings, if not found in mXXXXsim.h file.
- */
-#ifndef	ICR_INTRCONF
-#define	ICR_INTRCONF		0x2b            /* PIT1 level 5, priority 3 */
-#endif
-#ifndef	MCFPIT_IMR
-#define	MCFPIT_IMR		MCFINTC_IMRH
-#endif
-#ifndef	MCFPIT_IMR_IBIT
-#define	MCFPIT_IMR_IBIT		(1 << (MCFINT_PIT1 - 32))
-#endif
-
-
 #ifndef __ASSEMBLY__
 /*
  *	Definition for the interrupt auto-vectoring support.

arch/m68knommu/platform/coldfire/pit.c

@@ -32,7 +32,6 @@
  */
 #define	FREQ	((MCF_CLK / 2) / 64)
 #define	TA(a)	(MCF_IPSBAR + MCFPIT_BASE1 + (a))
-#define	INTC0	(MCF_IPSBAR + MCFICM_INTC0)
 #define PIT_CYCLES_PER_JIFFY (FREQ / HZ)
 
 static u32 pit_cnt;
@@ -154,8 +153,6 @@ static struct clocksource pit_clk = {
 
 void hw_timer_init(void)
 {
-	u32 imr;
-
 	cf_pit_clockevent.cpumask = cpumask_of(smp_processor_id());
 	cf_pit_clockevent.mult = div_sc(FREQ, NSEC_PER_SEC, 32);
 	cf_pit_clockevent.max_delta_ns =
@@ -166,11 +163,6 @@ void hw_timer_init(void)
 
 	setup_irq(MCFINT_VECBASE + MCFINT_PIT1, &pit_irq);
 
-	__raw_writeb(ICR_INTRCONF, INTC0 + MCFINTC_ICR0 + MCFINT_PIT1);
-	imr = __raw_readl(INTC0 + MCFPIT_IMR);
-	imr &= ~MCFPIT_IMR_IBIT;
-	__raw_writel(imr, INTC0 + MCFPIT_IMR);
-
 	pit_clk.mult = clocksource_hz2mult(FREQ, pit_clk.shift);
 	clocksource_register(&pit_clk);
 }