Struct v4l2_subdev_edid and the VIDIOC_SUBDEV_G/S_EDID ioctls were
specific for subdevices, but for hardware with a simple video pipeline
you do not need/want to create subdevice nodes to just get/set the EDID.

Move the v4l2_subdev_edid struct to v4l2-common.h and rename as
v4l2_edid. Add the same ioctls to videodev2.h as well, thus allowing
this API to be used with both video nodes and v4l-subdev nodes.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The wrong ioctl numbers were used due to a copy-and-paste error.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org      # for v3.7 and up
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch adds the driver for the LM3646, dual LED Flash driver.
The LM3646 has two 1.5A sync. boost converter with dual white current source.
It is controlled via an I2C compatible interface.
Each flash brightness, torch brightness and enable/disable can be controlled.
Under voltage, input voltage monitor and thermal threshhold Faults are added.
Please refer the datasheet http://www.ti.com/lit/ds/snvs962/snvs962.pdfSigned-off-by: NDaniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Three Flash fault are added. V4L2_FLASH_FAULT_UNDER_VOLTAGE for the case low
voltage below the min. limit. V4L2_FLASH_FAULT_INPUT_VOLTAGE for the case
falling input voltage and chip adjust flash current not occur under voltage
event. V4L2_FLASH_FAULT_LED_OVER_TEMPERATURE for the case the temperature
exceed the maximun limit
Signed-off-by: NDaniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Descriptions for flash faults V4L2_FLASH_FAULT_UNDER_VOLTAGE,
V4L2_FLASH_FAULT_INPUT_VOLTAGE, and V4L2_FLASH_FAULT_LED_OVER_TEMPERATURE.

Removed spaces before tabs.
Signed-off-by: NDaniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

If we have no pdata defined and driver fails to register we leak memory.
Converting to devm_kzalloc prevents this to happen.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Let's keep the style for all comments in the code, namely using small letters
whenever it's possible.

There is no functional change.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

There is no need to keep the FSF address inside each file. Moreover, it might
change in future which will make this one obsolete.

There is no functional change.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Empty port nodes are allowed but currently unsupported as the
v4l2_of_get_next_endpoint() function assumes that all port nodes have at
least an endpoint. Fix this.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Since I'm currently unable to dedicate sufficient time to the maintainership
of these two drivers update their status to "orphan" until new maintainers
appear.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for MBUS YUV10 BT656 and BT601 formats at rcar driver.
Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fixes memory leak introduced by
commit 47d8c881.
Signed-off-by: NDean Anderson <linux-dev@sensoray.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Set permissions on the debug module parameter to make it appear in sysfs.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch fixes the following warning:

drivers/media/i2c/tvp5150.c: In function '__tvp5150_try_crop':
include/linux/kernel.h:762:17: warning: comparison of distinct pointer types lacks a cast [enabled by default]
  (void) (&__val == &__min);  \
                 ^
drivers/media/i2c/tvp5150.c:886:16: note: in expansion of macro 'clamp'
  rect->width = clamp(rect->width,
                ^
include/linux/kernel.h:763:17: warning: comparison of distinct pointer types lacks a cast [enabled by default]
  (void) (&__val == &__max);  \
                 ^
drivers/media/i2c/tvp5150.c:886:16: note: in expansion of macro 'clamp'
  rect->width = clamp(rect->width,
                ^
include/linux/kernel.h:762:17: warning: comparison of distinct pointer types lacks a cast [enabled by default]
  (void) (&__val == &__min);  \
                 ^
drivers/media/i2c/tvp5150.c:904:17: note: in expansion of macro 'clamp'
  rect->height = clamp(rect->height,
                 ^
include/linux/kernel.h:763:17: warning: comparison of distinct pointer types lacks a cast [enabled by default]
  (void) (&__val == &__max);  \
                 ^
drivers/media/i2c/tvp5150.c:904:17: note: in expansion of macro 'clamp'
  rect->height = clamp(rect->height,
                 ^
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This code is correct but the indenting is wrong and triggers a static
checker warning "add curly braces?".
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Use PCI_VENDOR_ID_INTEL instead of creating its own vendor ID #define.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The NV16M description contained some copy-and-paste text from NV12M,
suggesting that this format is a 4:2:0 format when it really is a
4:2:2 format.

Fixed the text.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

interruptible_sleep_on is racy and going away. In the arv driver that
race has probably never caused problems since it would require a whole
video frame to be captured before the read function has a chance to
go to sleep, but using wait_event_interruptible lets us kill off the
old interface. In order to do this, we have to slightly adapt the
meaning of the ar->start_capture field to distinguish between not having
started a frame and having completed it.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

If NO_DMA=y:

    warning: (VIDEO_DM6446_CCDC && VIDEO_DM355_CCDC && VIDEO_DM365_ISIF && VIDEO_OMAP2_VOUT && VIDEO_SH_VOU && VIDEO_VIU && VIDEO_TIMBERDALE && VIDEO_MX1 && VIDEO_OMAP1) selects VIDEOBUF_DMA_CONTIG which has unmet direct dependencies (MEDIA_SUPPORT && HAS_DMA)

    drivers/built-in.o: In function `videobuf_vm_close':
    videobuf-dma-contig.c:(.text+0x407aa0): undefined reference to `videobuf_queue_cancel'
    drivers/built-in.o: In function `__videobuf_dc_alloc':
    videobuf-dma-contig.c:(.text+0x407ba2): undefined reference to `dma_alloc_coherent'
    drivers/built-in.o: In function `__videobuf_mmap_mapper':
    videobuf-dma-contig.c:(.text+0x407d44): undefined reference to `dma_free_coherent'
    drivers/built-in.o: In function `free_buffer':
    sh_vou.c:(.text+0x41f73a): undefined reference to `videobuf_waiton'
    drivers/built-in.o: In function `sh_vou_poll':
    sh_vou.c:(.text+0x41f884): undefined reference to `videobuf_poll_stream'
    drivers/built-in.o: In function `sh_vou_buf_prepare':
    sh_vou.c:(.text+0x41fdf6): undefined reference to `videobuf_iolock'
    drivers/built-in.o: In function `sh_vou_reqbufs':
    sh_vou.c:(.text+0x4203b0): undefined reference to `videobuf_reqbufs'
    drivers/built-in.o: In function `sh_vou_querybuf':
    sh_vou.c:(.text+0x42040a): undefined reference to `videobuf_querybuf'
    drivers/built-in.o: In function `sh_vou_qbuf':
    sh_vou.c:(.text+0x42045e): undefined reference to `videobuf_qbuf'
    drivers/built-in.o: In function `sh_vou_dqbuf':
    sh_vou.c:(.text+0x4204c2): undefined reference to `videobuf_dqbuf'
    drivers/built-in.o: In function `sh_vou_streamon':
    sh_vou.c:(.text+0x420572): undefined reference to `videobuf_streamon'
    drivers/built-in.o: In function `sh_vou_streamoff':
    sh_vou.c:(.text+0x4205d2): undefined reference to `videobuf_streamoff'
    drivers/built-in.o: In function `sh_vou_mmap':
    sh_vou.c:(.text+0x420c46): undefined reference to `videobuf_mmap_mapper'

VIDEO_SH_VOU selects VIDEOBUF_DMA_CONTIG, which bypasses its dependency on
HAS_DMA.  Make VIDEO_SH_VOU depend on HAS_DMA to fix this.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

BUG_ON is unnecessarily strict.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

[media] drivers/media/usb/usbtv/usbtv-core.c:119:22: sparse: symbol 'usbtv_id_table' was not declared. Should it be static?

tree:   git://linuxtv.org/media_tree.git master
head:   a3550ea6
commit: a3550ea6 [499/499] [media] usbtv: split core and video implementation
reproduce: make C=1 CF=-D__CHECK_ENDIAN__

sparse warnings: (new ones prefixed by >>)

>> drivers/media/usb/usbtv/usbtv-core.c:119:22: sparse: symbol 'usbtv_id_table' was not declared. Should it be static?
>> drivers/media/usb/usbtv/usbtv-core.c:129:19: sparse: symbol 'usbtv_usb_driver' was not declared. Should it be static?
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

There are two troubles there:
	1) the bit error measure were not accumulating;
	2) it was missing the bit count.

Fix them.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

drivers/media/dvb-frontends/drx39xyj/drxj.c: In function 'ctrl_get_qam_sig_quality':
drivers/media/dvb-frontends/drx39xyj/drxj.c:9468:6: warning: variable 'ber_cnt' set but not used [-Wunused-but-set-variable]
  u32 ber_cnt = 0; /* BER count */
      ^

By reading the comment, it is said that BER should be calculated as:
	qam_pre_rs_ber = frac_times1e6( ber_cnt, rs_bit_cnt );

Also, it makes sense to take the mantissa into account, so fix the
code to do what's commented.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Now that everything is set, let's enable DVBv5 stats, for
applications that support it.

DVBv3 apps will still work.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

When the signal is 7, it means that no signal was received.

Value experimentally measured.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Instead of just assuming that the min resolution is 1E-6,
pass both bit error and bit counts for userspace to calculate
BER. The same applies for PER, for 8VSB. It is not clear how
to get the packet count for QAM. So, for now, don't expose PER
for QAM.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Convert the stats internally to use DVBv5. For now, it will keep
showing everything via DVBv3 API only, as the .len value were
not initialized.

That allows testing if the new stats code didn't break anything.

A latter patch will add the final bits for the DVBv5 stats to
fully work.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

We'll need to use this function. Restore it from the
git history.

This function will be used on the next patch.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

State is already used on other places for the state struct.
Don't use it here, to avoid troubles with latter patches.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

As reported when compiled with W=1:

drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘ctrl_set_channel’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:10340:26: warning: variable ‘common_attr’ set but not used [-Wunused-but-set-variable]
  struct drx_common_attr *common_attr = NULL;
                          ^
drivers/media/dvb-frontends/drx39xyj/drxj.c:10336:6: warning: variable ‘intermediate_freq’ set but not used [-Wunused-but-set-variable]
  s32 intermediate_freq = 0;
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fix a smatch warning:
	drivers/media/dvb-frontends/drx39xyj/drxj.c:11711 drx_ctrl_u_code() info: why not propagate 'rc' from request_firmware() instead of (-2)?
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This function is currently not used. However, it was meant to
be called at device release. So, add it there.

While here, remove the bad check, as reported by Dan, as
smatch warning:
	drivers/media/dvb-frontends/drx39xyj/drxj.c:20041 drxj_close() warn: variable dereferenced before check 'demod' (see line 20036)
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This driver doesn't export any external symbol, except for
the attach() method.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

There are large chunks of code at drx-j that aren't used. Most
of them are due to analog TV support. Well, just enabling them
won't make analog support work, as devices with DRX and analog
support requires an extra chip (avf4910).

We don't have drivers for it, nor the current device that uses
this frontend has support for analog TV.

So, let's just get rid of this code. If latter needed, this
patch can easily be reverted from git history.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

smatch warning:
	drivers/media/dvb-frontends/drx39xyj/drxj.c:20803 drx_ctrl_u_code() warn: variable dereferenced before check 'mc_info' (see line 20800)
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

As reported by the kbuild test robot <fengguang.wu@intel.com>:

drivers/built-in.o: In function `em28xx_dvb_init':
    em28xx-dvb.c:(.text+0x876f2c): undefined reference to `drx39xxj_attach'

That happens when CONFIG_VIDEO_EM28XX_DVB is selected, and neither
CONFIG_MEDIA_SUBDRV_AUTOSELECT or DVB_DRX39XYJ is selected.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fixes the following warnings:
	drivers/media/dvb-frontends/drx39xyj/drxj.c:16764:68: warning: dubious: x & !y
	drivers/media/dvb-frontends/drx39xyj/drxj.c:16778:68: warning: dubious: x & !y
	drivers/media/dvb-frontends/drx39xyj/drxj.c:16797:68: warning: dubious: x & !y
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fixes the following warnings:
	drivers/media/dvb-frontends/drx39xyj/drxj.c:1679:65: warning: Using plain integer as NULL pointer
	drivers/media/dvb-frontends/drx39xyj/drxj.c:1679:71: warning: Using plain integer as NULL pointer
	drivers/media/dvb-frontends/drx39xyj/drxj.c:1681:52: warning: Using plain integer as NULL pointer
	drivers/media/dvb-frontends/drx39xyj/drxj.c:1681:58: warning: Using plain integer as NULL pointer
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

No functional changes, but removes a duplicate check, if
!state->type_A.
Signed-off-by: NDave Jones <davej@fedoraproject.org>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fix sparse warning:
	drivers/media/dvb-frontends/drx39xyj/drxj.c:1039:16: sparse: symbol 'drxj_default_aud_data_g' was not declared. Should it be static?
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>