Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
大约 1 年 前同步成功

通知 156
Star 36
Fork 7
cloud-kernel
cloud-kernel

体验新版 GitCode，发现更多精彩内容 >>

切换分支/标签
  1. 10 12月, 2014 11 次提交
  3. 09 12月, 2014 4 次提交
    • A
      fib_trie: Fix /proc/net/fib_trie when CONFIG_IP_MULTIPLE_TABLES is not defined · a5a519b2
      由 Alexander Duyck 提交于 
      In recent testing I had disabled CONFIG_IP_MULTIPLE_TABLES and as a result
when I ran "cat /proc/net/fib_trie" the main trie was displayed multiple
times.  I found that the problem line of code was in the function
fib_trie_seq_next.  Specifically the line below caused the indexes to go in
the opposite direction of our traversal:

	h = tb->tb_id & (FIB_TABLE_HASHSZ - 1);

This issue was that the RT tables are defined such that RT_TABLE_LOCAL is ID
255, while it is located at TABLE_LOCAL_INDEX of 0, and RT_TABLE_MAIN is 254
with a TABLE_MAIN_INDEX of 1.  This means that the above line will return 1
for the local table and 0 for main.  The result is that fib_trie_seq_next
will return NULL at the end of the local table, fib_trie_seq_start will
return the start of the main table, and then fib_trie_seq_next will loop on
main forever as h will always return 0.

The fix for this is to reverse the ordering of the two tables.  It has the
advantage of making it so that the tables now print in the same order
regardless of if multiple tables are enabled or not.  In order to make the
definition consistent with the multiple tables case I simply masked the to
RT_TABLE_XXX values by (FIB_TABLE_HASHSZ - 1).  This way the two table
layouts should always stay consistent.

Fixes: 93456b6d ("[IPV4]: Unify access to the routing tables")
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      a5a519b2
    • E
      net: mvneta: fix race condition in mvneta_tx() · 5f478b41
      由 Eric Dumazet 提交于 
      mvneta_tx() dereferences skb to get skb->len too late,
as hardware might have completed the transmit and TX completion
could have freed the skb from another cpu.

Fixes: 71f6d1b3 ("net: mvneta: replace Tx timer with a real interrupt")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      5f478b41
    • W
      net: mvneta: fix Tx interrupt delay · aebea2ba
      由 willy tarreau 提交于 
      The mvneta driver sets the amount of Tx coalesce packets to 16 by
default. Normally that does not cause any trouble since the driver
uses a much larger Tx ring size (532 packets). But some sockets
might run with very small buffers, much smaller than the equivalent
of 16 packets. This is what ping is doing for example, by setting
SNDBUF to 324 bytes rounded up to 2kB by the kernel.

The problem is that there is no documented method to force a specific
packet to emit an interrupt (eg: the last of the ring) nor is it
possible to make the NIC emit an interrupt after a given delay.

In this case, it causes trouble, because when ping sends packets over
its raw socket, the few first packets leave the system, and the first
15 packets will be emitted without an IRQ being generated, so without
the skbs being freed. And since the socket's buffer is small, there's
no way to reach that amount of packets, and the ping ends up with
"send: no buffer available" after sending 6 packets. Running with 3
instances of ping in parallel is enough to hide the problem, because
with 6 packets per instance, that's 18 packets total, which is enough
to grant a Tx interrupt before all are sent.

The original driver in the LSP kernel worked around this design flaw
by using a software timer to clean up the Tx descriptors. This timer
was slow and caused terrible network performance on some Tx-bound
workloads (such as routing) but was enough to make tools like ping
work correctly.

Instead here, we simply set the packet counts before interrupt to 1.
This ensures that each packet sent will produce an interrupt. NAPI
takes care of coalescing interrupts since the interrupt is disabled
once generated.

No measurable performance impact nor CPU usage were observed on small
nor large packets, including when saturating the link on Tx, and this
fixes tools like ping which rely on too small a send buffer. If one
wants to increase this value for certain workloads where it is safe
to do so, "ethtool -C $dev tx-frames" will override this default
setting.

This fix needs to be applied to stable kernels starting with 3.10.
Tested-By: NMaggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: NWilly Tarreau <w@1wt.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      aebea2ba
    • D
      mips: bpf: Fix broken BPF_MOD · 2e46477a
      由 Denis Kirjanov 提交于 
      Remove optimize_div() from BPF_MOD | BPF_K case
since we don't know the dividend and fix the
emit_mod() by reading the mod operation result from HI register
Signed-off-by: NDenis Kirjanov <kda@linux-powerpc.org>
Reviewed-by: NMarkos Chandras <markos.chandras@imgtec.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      2e46477a
  5. 06 12月, 2014 7 次提交
  7. 04 12月, 2014 16 次提交
  9. 03 12月, 2014 2 次提交