The existing interface only has a pre-order callback. This change
adds an additional parameter for a post-order callback which will
be more useful for bus scans. ACPICA BZ 779.

Also update the external calls to acpi_walk_namespace.

http://www.acpica.org/bugzilla/show_bug.cgi?id=779Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Change SB900 to its formal code name Hudson-2.
Signed-off-by: NCrane Cai <crane.cai@amd.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The driver always ends a read with a STOP condition which
breaks subsequent I2C reads/writes in the same transaction as
these expect to do a repeated START(ReSTART).

This will also help I2C multimaster as the bus will not be released
after the first read, but when the whole transaction ends.
Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Enable clock before START, disable it after STOP.
Signed-off-by: NRichard Zhao <linuxzsc@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

check cpu_is_mx1() when disable delay.
Signed-off-by: NRichard Zhao <linuxzsc@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The controller can't do anything else before it actually generates START/STOP.
So we check busy bit to make sure START/STOP is successfully finished.

If we don't check busy bit, START/STOP may fail on some fast CPUs.
Signed-off-by: NRichard Zhao <linuxzsc@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

When an ACPI resource conflict is detected, error messages are already
printed by ACPI. There's no point in causing the driver core to print
more error messages, so return one of the error codes for which no
message is printed.

This fixes bug #14293:
http://bugzilla.kernel.org/show_bug.cgi?id=14293Signed-off-by: NJean Delvare <khali@linux-fr.org>

We recently removed the acpi_device_uid() interface because nobody
used it.  I don't think it's essential here either.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

As I2C is used by PMICs also, make the busses available early via
subsys_initcall().
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The mv64xxx_i2c_intr() irq handler in drivers/i2c/busses/i2c-mv64xxx.c
is declared as returning 'int', resulting in this compile-time warning:

drivers/i2c/busses/i2c-mv64xxx.c: In function 'mv64xxx_i2c_probe':
drivers/i2c/busses/i2c-mv64xxx.c:540: warning: passing argument 2 of 'request_irq' from incompatible pointer type

Fix: correct the return type to 'irqreturn_t'.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Now that we have ACPI-based SMBus controller drivers, and we will start
telling users to use them instead of native drivers when I/O resources
conflict, I think it would be good to clearly mark ACPI drivers as such
in Kconfig.

This is exactly the same as we just did for hwmon drivers.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Crane Cai <crane.cai@amd.com>

This driver supports the SMBus Control Method Interface. It needs BIOS declare
ACPI control methods which described in SMBus Control Method Interface Spec.
http://smbus.org/specs/smbus_cmi10.pdfSigned-off-by: NCrane Cai <crane.cai@amd.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

request_mem_region should be used when ioremap is used subsequently.
release_region is then correspondingly replaced by release_mem_region.

The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
expression start,E;
@@

- request_region
+ request_mem_region
  (start,...)
... when != request_mem_region(start,...)
    when != start = E
ioremap(start,...)

@@
expression r.start;
@@

- release_region
+ release_mem_region
  (start,...)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Cc: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add new SMBus device ID for AMD SB900.
Signed-off-by: NCrane Cai <crane.cai@amd.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The pcf8574 driver in drivers/i2c/chips which just exports its register to
sysfs is superseded by drivers/gpio/pcf857x.c which properly uses the gpiolib.
As this driver has been deprecated for more than a year, finally remove it.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The pca9539 driver in drivers/i2c/chips which just exports its registers to
sysfs is superseded by drivers/gpio/pca953x.c which properly uses the gpiolib.
As this driver has been deprecated for more than a year, finally remove it.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NBen Gardner <gardner.ben@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The pcf8575 driver in drivers/i2c/chips which just exports its register to
sysfs is superseded by drivers/gpio/pcf857x.c which properly uses the gpiolib.
As this driver has been deprecated for more than a year, finally remove it.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Upon a bus error, it's rather hard to guess what happened. Dumping the
address, length and status provides a lot of value for troubleshooting
issues.
Signed-off-by: NWilly Tarreau <wtarreau@exceliance.fr>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Some user-space applications may be relying on i2c adapters showing up
as class devices in sysfs. Provide compatibility links for them for
the time being. We will remove them after a long transition period.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>

Kay says i2c adapters shouldn't be class devices but bus devices.
Convert them that way, using a device type.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>

This is required for upcoming changes.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>

Make the I/O faster, mainly by using combined SMBus transactions when
possible. While the TSL2550 datasheet doesn't say the device supports
them, they seem to work just fine in practice, and a combined
transaction is faster than two simple transactions in many cases and
always more reliable.

A side effect is to suppress the delays between SMBus writes and
reads. The datasheet doesn't say they are needed and things work just
fine for me without them.

I also couldn't see any reason for the delay between reading the two
channels. Nor for the loop to get a reading in the first place. The
400 ms delay between samples only matters at chip power-up, after that
the chip always hold the previously sampled value so we never get to
wait.

All these changes make reading the lux value much faster and cheaper.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Tested-by: NMichele De Candia <michele.decandia@valueteam.com>
Cc: Rodolfo Giometti <giometti@linux.it>

When echo is on, we waste time reading back our orders. Switching echo
off makes performance much better: SMBus byte data transactions are 47%
faster and byte transactions are 24% faster.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

PXA I2C module is also used in Marvell PXA168 and PXA910 series.
Update the module dependancy of PXA I2C.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This patch modifies the SuperH Mobile I2C driver to support
Runtime PM. These changes is all that is needed for proper
Runtime PM support in this driver. Driver callbacks for
Runtime PM are empty because the device registers are always
re-initialized after pm_runtime_get_sync().
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

- blk clk is enabled when an irq arrives. The clk should be enabled,
  but just to make sure.
- All error bits are handled no matter state machine state
- All irq's will run complete() except for irq's that wasn't an event.
- No more looking into status registers just in case an interrupt
  has happend and the irq handle wasn't executed.
- irq_disable/enable are now separete functions.
- clk settings calculation changed to round upwards instead of
  downwards.
- Number of address send attempts before giving up is increased to 12
  from 10 since it most times take 8 tries before getting through.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Silicon Errata 1.153 has been fixed on OMAP 3630|4430 with the use of a later
version of I2C IP block.

The errata impacts OMAP 2420|2430|3430, enable the workaround for these based
on I2C IP block revision number instead of OMAP CPU type
Signed-off-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com
Reviewed-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

ACK any pending read/write interrupts before exiting the ISR either after
completing the operation [ARDY interrupt] or in case of an error
[NACK|AL interrupt]
Signed-off-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

I2C status ack for [RX]RDR and [RX]RDY could
cause race conditions of clearing the event
twice and a violation of the programing
sequence as defined in TRM This patch fixes
the same.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

When an XRDY/XDR is hit, wait for XUDF before writing data to DATA_REG.
Otherwise some data bytes can be lost while transferring them from the
memory to the I2C interface.

Do a Busy-wait for XUDF, before writing data to DATA_REG. While waiting
if there is NACK | AL, set the appropriate error flags, ack the pending
interrupts and return from the ISR.
Signed-off-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NVikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

In case of a NACK or ARDY or AL interrupt, complete the request.
There is no need to service the RRDY/RDR or XRDY/XDR interrupts.

Refer TRM SWPU114: Figure 18-31.I2C Master Transmitter Mode, Interrupt Method,
in F/S and HS Modes

http://focus.ti.com/pdfs/wtbu/SWPU114T_PrelimFinalEPDF_06_25_2009.pdfSigned-off-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NVikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Fix bug in reading the I2C_BUFFSTAT register for getting byte count on RX/TX interrupt.

On Interrupt: I2C_STAT[RDR],
	read 'RXSTAT' from I2C_BUFFSTAT[8-13]
On Interrupt: I2C_STAT[XDR]
	read 'TXSTAT' from I2C_BUFFSTAT[0-5]
Signed-off-by: NJagadeesh Pakaravoor <j-pakaravoor@ti.com>
Signed-off-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NVikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Convert the i2c-sh_mobile i2c bus driver to use
subsys_initcall() instead of module_init().

This change makes the driver register a bit earlier which
together with earlier platform data moves the time for probe().
The earlier probe() makes it possible to use i2c_get_adapter()
and i2c_transfer() from device_initcall().

The same strategy is used by other i2c bus drivers such as
i2c-pxa.c and i2c-s3c2410.c.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
[ben-linux@fluff.org: minor subject updaye]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

strlcpy() will always null terminate the string.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

s3c24xx_i2c_init() was overwriting the IICLC value set just above in
s3c24xx_i2c_clockrate() with zero, effectively disabling the platform
line control setting.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

I've tested TSL2550 driver and I've found a bug: when light is off, 
returned value from tsl2550_calculate_lux function is -1 when it should 
be 0 (sensor correctly read that light was off).

I think the bug is that a zero c0 value (approximated value of ch0) is 
misinterpreted as an error. 
Signed-off-by: NMichele Jr De Candia <michele.decandia@valueteam.com>
Acked-by: NRodolfo Giometti <giometti@linux.it>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Convert the i2c-sh_mobile i2c bus driver to use
subsys_initcall() instead of module_init().

This change makes the driver register a bit earlier which
together with earlier platform data moves the time for probe().
The earlier probe() makes it possible to use i2c_get_adapter()
and i2c_transfer() from device_initcall().

The same strategy is used by other i2c bus drivers such as
i2c-pxa.c and i2c-s3c2410.c.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This is V2 of the i2c-s3c2410 dev_pm_ops patch.

The callbacks are converted for CONFIG_SUSPEND like this:
  suspend_late() -> suspend_noirq()
  resume() -> resume()
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

This patch reworks platform driver power management code
for i2c-pxa from legacy late/early callbacks to dev_pm_ops.

The callbacks are converted for CONFIG_SUSPEND like this:
  suspend_late() -> suspend_noirq()
  resume_early() -> resume_noirq()
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Use the function resource_size, which reduces the chance of introducing
off-by-one errors in calculating the resource size.

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
struct resource *res;
@@

- (res->end - res->start) + 1
+ resource_size(res)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>