In order to separate the different parts of the
driver better, we are reducing the shared data.
This moves the workqueue to "priv", and removes
it from the transport. To do this, simply use
schedule_work() in the transport.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Make iwlwifi record all debug messages into
tracing, even if debug_level is not enabled.
Due to the lack of APIs, the debug messages
are now recorded up to a max length of 100,
the only one above that is the RXON which is
not needed if you trace the commands as well
as it only dumps the command contents.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>

The testmode command for host command send now replies
with a nl80211 message and the response it recieved from
the device.

This does not change the API directly, but adds a reply
to the testmode call.
Signed-off-by: NAmit Beka <amit.beka@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Replaced the old SRAM and periphery indirect access functions
with a unified indirect memory access functions. These include
new IWL_TM_CMDs for buffer read/write/dump which replace the
SRAM read/dump commands, but the API for IWL_TM_CMD_INDIRECT_REG
read/write will now not be supported (returns error).

This also handles writing to periphery registers in 1-3 bytes.

Requires the corresponding patch in the library for the API change.
Signed-off-by: NAmit Beka <amit.beka@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

A lot of error conditions in testmode log as IWL_DEBUG_INFO which is not
logged by default. Change it
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Conflicts:
	net/mac80211/debugfs_sta.c
	net/mac80211/sta_info.h

Rate control algorithms are supposed to stop processing when they
encounter a rate with the index -1.  Checking for rate->count not being
zero is not enough.

Allowing a rate with negative index leads to memory corruption in
ath_debug_stat_rc().

One consequence of the bug is discussed at
https://bugzilla.redhat.com/show_bug.cgi?id=768639Signed-off-by: NPavel Roskin <proski@gnu.org>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Driver maintains different flags for WEP, WPA, WPA2 security modes.
Appropriate flag is set using security information provided in
connect request. mwifiex_is_network_compatible() routine uses them
to check if driver's setting is compatible with AP. Association is
aborted if the routine fails.

For some corner cases, it is observed that association is failed
even for valid security information based on association history.
This patch fixes the problem by clearing previous security setting
during each association.

We should set WEP key provided in connect request as default tx key.
This missing change is also added here.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Most rate control implementations assume .get_rate and .tx_status are only
called once the per-station data has been fully initialized.
minstrel_ht crashes if this assumption is violated.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Tested-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are situations where we don't have the
necessary rate control information yet for
station entries, e.g. when associating. This
currently doesn't really happen due to the
dummy station handling; explicitly disabling
rate control when it's not initialised will
allow us to remove dummy stations.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We need to use the _sync() version for cancelling the info and security
timer in the L2CAP connection delete path. Otherwise the delayed work
handler might run after the connection object is freed.
Signed-off-by: NUlisses Furquim <ulisses@profusion.mobi>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

__cancel_delayed_work() is being used in some paths where we cannot
sleep waiting for the delayed work to finish. However, that function
might return while the timer is running and the work will be queued
again. Replace the calls with safer cancel_delayed_work() version
which spins until the timer handler finishes on other CPUs and
cancels the delayed work.
Signed-off-by: NUlisses Furquim <ulisses@profusion.mobi>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21f3 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=74DE2B344A7B
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: NManoj Iyer <manoj.iyer@canonical.com>
Tested-by: NDennis Chua <dennis.chua@canonical.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

We should only perform a reset in hci_dev_do_close if the
HCI_QUIRK_NO_RESET flag is set (since in such a case a reset will not be
performed when initializing the device).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

There is an imbalance in the rfcomm_session_hold / rfcomm_session_put
operations which causes the following crash:

[  685.010159] BUG: unable to handle kernel paging request at 6b6b6b6b
[  685.010169] IP: [<c149d76d>] rfcomm_process_dlcs+0x1b/0x15e
[  685.010181] *pdpt = 000000002d665001 *pde = 0000000000000000
[  685.010191] Oops: 0000 [#1] PREEMPT SMP
[  685.010247]
[  685.010255] Pid: 947, comm: krfcommd Tainted: G         C  3.0.16-mid8-dirty #44
[  685.010266] EIP: 0060:[<c149d76d>] EFLAGS: 00010246 CPU: 1
[  685.010274] EIP is at rfcomm_process_dlcs+0x1b/0x15e
[  685.010281] EAX: e79f551c EBX: 6b6b6b6b ECX: 00000007 EDX: e79f40b4
[  685.010288] ESI: e79f4060 EDI: ed4e1f70 EBP: ed4e1f68 ESP: ed4e1f50
[  685.010295]  DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[  685.010303] Process krfcommd (pid: 947, ti=ed4e0000 task=ed43e5e0 task.ti=ed4e0000)
[  685.010308] Stack:
[  685.010312]  ed4e1f68 c149eb53 e5925150 e79f4060 ed500000 ed4e1f70 ed4e1f80 c149ec10
[  685.010331]  00000000 ed43e5e0 00000000 ed4e1f90 ed4e1f9c c149ec87 0000bf54 00000000
[  685.010348]  00000000 ee03bf54 c149ec37 ed4e1fe4 c104fe01 00000000 00000000 00000000
[  685.010367] Call Trace:
[  685.010376]  [<c149eb53>] ? rfcomm_process_rx+0x6e/0x74
[  685.010387]  [<c149ec10>] rfcomm_process_sessions+0xb7/0xde
[  685.010398]  [<c149ec87>] rfcomm_run+0x50/0x6d
[  685.010409]  [<c149ec37>] ? rfcomm_process_sessions+0xde/0xde
[  685.010419]  [<c104fe01>] kthread+0x63/0x68
[  685.010431]  [<c104fd9e>] ? __init_kthread_worker+0x42/0x42
[  685.010442]  [<c14dae82>] kernel_thread_helper+0x6/0xd

This issue has been brought up earlier here:

https://lkml.org/lkml/2011/5/21/127

The issue appears to be the rfcomm_session_put in rfcomm_recv_ua. This
operation doesn't seem be to required as for the non-initiator case we
have the rfcomm_process_rx doing an explicit put and in the initiator
case the last dlc_unlink will drive the reference counter to 0.

There have been several attempts to fix these issue:

6c2718da Bluetooth: Do not call rfcomm_session_put() for RFCOMM UA on closed socket
683d949a Bluetooth: Never deallocate a session when some DLC points to it

but AFAICS they do not fix the issue just make it harder to reproduce.
Signed-off-by: NOctavian Purdila <octavian.purdila@intel.com>
Signed-off-by: NGopala Krishna Murala <gopala.krishna.murala@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

We don't need to use the _sync variant in hci_conn_hold and
hci_conn_put to cancel conn->disc_work delayed work. This way
we avoid potential deadlocks like this one reported by lockdep.

======================================================
[ INFO: possible circular locking dependency detected ]
3.2.0+ #1 Not tainted
-------------------------------------------------------
kworker/u:1/17 is trying to acquire lock:
 (&hdev->lock){+.+.+.}, at: [<ffffffffa0041155>] hci_conn_timeout+0x62/0x158 [bluetooth]

but task is already holding lock:
 ((&(&conn->disc_work)->work)){+.+...}, at: [<ffffffff81035751>] process_one_work+0x11a/0x2bf

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #2 ((&(&conn->disc_work)->work)){+.+...}:
       [<ffffffff81057444>] lock_acquire+0x8a/0xa7
       [<ffffffff81034ed1>] wait_on_work+0x3d/0xaa
       [<ffffffff81035b54>] __cancel_work_timer+0xac/0xef
       [<ffffffff81035ba4>] cancel_delayed_work_sync+0xd/0xf
       [<ffffffffa00554b0>] smp_chan_create+0xde/0xe6 [bluetooth]
       [<ffffffffa0056160>] smp_conn_security+0xa3/0x12d [bluetooth]
       [<ffffffffa0053640>] l2cap_connect_cfm+0x237/0x2e8 [bluetooth]
       [<ffffffffa004239c>] hci_proto_connect_cfm+0x2d/0x6f [bluetooth]
       [<ffffffffa0046ea5>] hci_event_packet+0x29d1/0x2d60 [bluetooth]
       [<ffffffffa003dde3>] hci_rx_work+0xd0/0x2e1 [bluetooth]
       [<ffffffff810357af>] process_one_work+0x178/0x2bf
       [<ffffffff81036178>] worker_thread+0xce/0x152
       [<ffffffff81039a03>] kthread+0x95/0x9d
       [<ffffffff812e7754>] kernel_thread_helper+0x4/0x10

-> #1 (slock-AF_BLUETOOTH-BTPROTO_L2CAP){+.+...}:
       [<ffffffff81057444>] lock_acquire+0x8a/0xa7
       [<ffffffff812e553a>] _raw_spin_lock_bh+0x36/0x6a
       [<ffffffff81244d56>] lock_sock_nested+0x24/0x7f
       [<ffffffffa004d96f>] lock_sock+0xb/0xd [bluetooth]
       [<ffffffffa0052906>] l2cap_chan_connect+0xa9/0x26f [bluetooth]
       [<ffffffffa00545f8>] l2cap_sock_connect+0xb3/0xff [bluetooth]
       [<ffffffff81243b48>] sys_connect+0x69/0x8a
       [<ffffffff812e6579>] system_call_fastpath+0x16/0x1b

-> #0 (&hdev->lock){+.+.+.}:
       [<ffffffff81056d06>] __lock_acquire+0xa80/0xd74
       [<ffffffff81057444>] lock_acquire+0x8a/0xa7
       [<ffffffff812e3870>] __mutex_lock_common+0x48/0x38e
       [<ffffffff812e3c75>] mutex_lock_nested+0x2a/0x31
       [<ffffffffa0041155>] hci_conn_timeout+0x62/0x158 [bluetooth]
       [<ffffffff810357af>] process_one_work+0x178/0x2bf
       [<ffffffff81036178>] worker_thread+0xce/0x152
       [<ffffffff81039a03>] kthread+0x95/0x9d
       [<ffffffff812e7754>] kernel_thread_helper+0x4/0x10

other info that might help us debug this:

Chain exists of:
  &hdev->lock --> slock-AF_BLUETOOTH-BTPROTO_L2CAP --> (&(&conn->disc_work)->work)

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock((&(&conn->disc_work)->work));
                               lock(slock-AF_BLUETOOTH-BTPROTO_L2CAP);
                               lock((&(&conn->disc_work)->work));
  lock(&hdev->lock);

 *** DEADLOCK ***

2 locks held by kworker/u:1/17:
 #0:  (hdev->name){.+.+.+}, at: [<ffffffff81035751>] process_one_work+0x11a/0x2bf
 #1:  ((&(&conn->disc_work)->work)){+.+...}, at: [<ffffffff81035751>] process_one_work+0x11a/0x2bf

stack backtrace:
Pid: 17, comm: kworker/u:1 Not tainted 3.2.0+ #1
Call Trace:
 [<ffffffff812e06c6>] print_circular_bug+0x1f8/0x209
 [<ffffffff81056d06>] __lock_acquire+0xa80/0xd74
 [<ffffffff81021ef2>] ? arch_local_irq_restore+0x6/0xd
 [<ffffffff81022bc7>] ? vprintk+0x3f9/0x41e
 [<ffffffff81057444>] lock_acquire+0x8a/0xa7
 [<ffffffffa0041155>] ? hci_conn_timeout+0x62/0x158 [bluetooth]
 [<ffffffff812e3870>] __mutex_lock_common+0x48/0x38e
 [<ffffffffa0041155>] ? hci_conn_timeout+0x62/0x158 [bluetooth]
 [<ffffffff81190fd6>] ? __dynamic_pr_debug+0x6d/0x6f
 [<ffffffffa0041155>] ? hci_conn_timeout+0x62/0x158 [bluetooth]
 [<ffffffff8105320f>] ? trace_hardirqs_off+0xd/0xf
 [<ffffffff812e3c75>] mutex_lock_nested+0x2a/0x31
 [<ffffffffa0041155>] hci_conn_timeout+0x62/0x158 [bluetooth]
 [<ffffffff810357af>] process_one_work+0x178/0x2bf
 [<ffffffff81035751>] ? process_one_work+0x11a/0x2bf
 [<ffffffff81055af3>] ? lock_acquired+0x1d0/0x1df
 [<ffffffffa00410f3>] ? hci_acl_disconn+0x65/0x65 [bluetooth]
 [<ffffffff81036178>] worker_thread+0xce/0x152
 [<ffffffff810407ed>] ? finish_task_switch+0x45/0xc5
 [<ffffffff810360aa>] ? manage_workers.isra.25+0x16a/0x16a
 [<ffffffff81039a03>] kthread+0x95/0x9d
 [<ffffffff812e7754>] kernel_thread_helper+0x4/0x10
 [<ffffffff812e5db4>] ? retint_restore_args+0x13/0x13
 [<ffffffff8103996e>] ? __init_kthread_worker+0x55/0x55
 [<ffffffff812e7750>] ? gs_change+0x13/0x13
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@openbossa.org>
Reviewed-by: NUlisses Furquim <ulisses@profusion.mobi>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Since bluetooth uses multiple protocols types, to avoid lockdep
warnings, we need to use different lockdep classes (one for each
protocol type).

This is already done in bt_sock_create but it misses a couple of cases
when new connections are created. This patch corrects that to fix the
following warning:

<4>[ 1864.732366] =======================================================
<4>[ 1864.733030] [ INFO: possible circular locking dependency detected ]
<4>[ 1864.733544] 3.0.16-mid3-00007-gc9a0f62 #3
<4>[ 1864.733883] -------------------------------------------------------
<4>[ 1864.734408] t.android.btclc/4204 is trying to acquire lock:
<4>[ 1864.734869]  (rfcomm_mutex){+.+.+.}, at: [<c14970ea>] rfcomm_dlc_close+0x15/0x30
<4>[ 1864.735541]
<4>[ 1864.735549] but task is already holding lock:
<4>[ 1864.736045]  (sk_lock-AF_BLUETOOTH){+.+.+.}, at: [<c1498bf7>] lock_sock+0xa/0xc
<4>[ 1864.736732]
<4>[ 1864.736740] which lock already depends on the new lock.
<4>[ 1864.736750]
<4>[ 1864.737428]
<4>[ 1864.737437] the existing dependency chain (in reverse order) is:
<4>[ 1864.738016]
<4>[ 1864.738023] -> #1 (sk_lock-AF_BLUETOOTH){+.+.+.}:
<4>[ 1864.738549]        [<c1062273>] lock_acquire+0x104/0x140
<4>[ 1864.738977]        [<c13d35c1>] lock_sock_nested+0x58/0x68
<4>[ 1864.739411]        [<c1493c33>] l2cap_sock_sendmsg+0x3e/0x76
<4>[ 1864.739858]        [<c13d06c3>] __sock_sendmsg+0x50/0x59
<4>[ 1864.740279]        [<c13d0ea2>] sock_sendmsg+0x94/0xa8
<4>[ 1864.740687]        [<c13d0ede>] kernel_sendmsg+0x28/0x37
<4>[ 1864.741106]        [<c14969ca>] rfcomm_send_frame+0x30/0x38
<4>[ 1864.741542]        [<c1496a2a>] rfcomm_send_ua+0x58/0x5a
<4>[ 1864.741959]        [<c1498447>] rfcomm_run+0x441/0xb52
<4>[ 1864.742365]        [<c104f095>] kthread+0x63/0x68
<4>[ 1864.742742]        [<c14d5182>] kernel_thread_helper+0x6/0xd
<4>[ 1864.743187]
<4>[ 1864.743193] -> #0 (rfcomm_mutex){+.+.+.}:
<4>[ 1864.743667]        [<c1061ada>] __lock_acquire+0x988/0xc00
<4>[ 1864.744100]        [<c1062273>] lock_acquire+0x104/0x140
<4>[ 1864.744519]        [<c14d2c70>] __mutex_lock_common+0x3b/0x33f
<4>[ 1864.744975]        [<c14d303e>] mutex_lock_nested+0x2d/0x36
<4>[ 1864.745412]        [<c14970ea>] rfcomm_dlc_close+0x15/0x30
<4>[ 1864.745842]        [<c14990d9>] __rfcomm_sock_close+0x5f/0x6b
<4>[ 1864.746288]        [<c1499114>] rfcomm_sock_shutdown+0x2f/0x62
<4>[ 1864.746737]        [<c13d275d>] sys_socketcall+0x1db/0x422
<4>[ 1864.747165]        [<c14d42f0>] syscall_call+0x7/0xb
Signed-off-by: NOctavian Purdila <octavian.purdila@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

queue_delayed_work() expects a relative time for when that work
should be scheduled.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

After moving L2CAP timers to workqueues l2cap_set_timer expects timeout
value to be specified in jiffies but constants defined in miliseconds
are used. This makes timeouts unreliable when CONFIG_HZ is not set to
1000.

__set_chan_timer macro still uses jiffies as input to avoid multiple
conversions from/to jiffies for sk_sndtimeo value which is already
specified in jiffies.
Signed-off-by: NAndrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Ackec-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

sk_sndtime value should be specified in jiffies thus initial value
needs to be converted from miliseconds. Otherwise this timeout is
unreliable when CONFIG_HZ is not set to 1000.
Signed-off-by: NAndrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

As reported by Dan Carpenter this function causes a Sparse warning and
shouldn't be declared inline:

include/net/bluetooth/l2cap.h:837:30 error: marked inline, but without a
definition"
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

[ 2096.384084] btusb_send_frame:684: hci0
[ 2096.384087] usb 3-1: BOGUS urb flags, 2 --> 0
[ 2096.384091] Bluetooth: hci0 urb ffff8801b61d3a80 submission failed (22)

According the documentation in usb_submit_urb() URB_ISO_ASAP
flag is only allowed for endpoints of type USB_ENDPOINT_XFER_ISOC.

This reverts commit b8aabfc9.
Signed-off-by: NDaniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Commit 33060542 fixed l2cap conn establishment for non-ssp remote
devices by not setting HCI_CONN_ENCRYPT_PEND every time conn security
is tested (which was always returning failure on any subsequent
security checks).

However, this broke l2cap conn establishment for ssp remote devices
when an ACL link was already established at SDP-level security. This
fix ensures that encryption must be pending whenever authentication
is also pending.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-by: NDaniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Fixes problem where caller would think routine succeeded when it failed
leading to divide by zero panic.
Signed-off-by: NSimon Graham <simon.graham@virtualcomputer.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

read_lock(&tpt_trig->trig.leddev_list_lock) is accessed via the path
ieee80211_open (->) ieee80211_do_open (->) ieee80211_mod_tpt_led_trig
(->) ieee80211_start_tpt_led_trig (->) tpt_trig_timer before initializing
it.
the intilization of this read/write lock happens via the path
ieee80211_led_init (->) led_trigger_register, but we are doing
'ieee80211_led_init'  after 'ieeee80211_if_add' where we
register netdev_ops.
so we access leddev_list_lock before initializing it and causes the
following bug in chrome laptops with AR928X cards with the following
script

while true
do
sudo modprobe -v ath9k
sleep 3
sudo modprobe -r ath9k
sleep 3
done

	BUG: rwlock bad magic on CPU#1, wpa_supplicant/358, f5b9eccc
	Pid: 358, comm: wpa_supplicant Not tainted 3.0.13 #1
	Call Trace:

	[<8137b9df>] rwlock_bug+0x3d/0x47
	[<81179830>] do_raw_read_lock+0x19/0x29
	[<8137f063>] _raw_read_lock+0xd/0xf
	[<f9081957>] tpt_trig_timer+0xc3/0x145 [mac80211]
	[<f9081f3a>] ieee80211_mod_tpt_led_trig+0x152/0x174 [mac80211]
	[<f9076a3f>] ieee80211_do_open+0x11e/0x42e [mac80211]
	[<f9075390>] ? ieee80211_check_concurrent_iface+0x26/0x13c [mac80211]
	[<f9076d97>] ieee80211_open+0x48/0x4c [mac80211]
	[<812dbed8>] __dev_open+0x82/0xab
	[<812dc0c9>] __dev_change_flags+0x9c/0x113
	[<812dc1ae>] dev_change_flags+0x18/0x44
	[<8132144f>] devinet_ioctl+0x243/0x51a
	[<81321ba9>] inet_ioctl+0x93/0xac
	[<812cc951>] sock_ioctl+0x1c6/0x1ea
	[<812cc78b>] ? might_fault+0x20/0x20
	[<810b1ebb>] do_vfs_ioctl+0x46e/0x4a2
	[<810a6ebb>] ? fget_light+0x2f/0x70
	[<812ce549>] ? sys_recvmsg+0x3e/0x48
	[<810b1f35>] sys_ioctl+0x46/0x69
	[<8137fa77>] sysenter_do_call+0x12/0x2

Cc: <stable@vger.kernel.org>
Cc: Gary Morain <gmorain@google.com>
Cc: Paul Stewart <pstew@google.com>
Cc: Abhijit Pradhan <abhijit@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Acked-by: NJohannes Berg <johannes.berg@intel.com>
Tested-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixes problem where caller would think routine succeeded when it failed
leading to divide by zero panic.

(This also reverts an earlier attempt, commit 42bc0c97 "rtlwifi: Return
correct failure code on error". -- JWL)
Signed-off-by: NSimon Graham <simon.graham@virtualcomputer.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Most rate control implementations assume .get_rate and .tx_status are only
called once the per-station data has been fully initialized.
minstrel_ht crashes if this assumption is violated.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Tested-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Callers of rtl_pci_init expect zero to be returned on error. Returning
the error code leads to, amongst other things, divide by zero panics
attempting to use the ring size that is set to zero.
Signed-off-by: NSimon Graham <simon.graham@virtualcomputer.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If you want to use mesh support from mac80211 on a recent
kernel on 2.6.24 you'll run into a name clash when compiling
against include/linux/namei.h, so rename this routine.

/home/mcgrof/tmp/compat-wireless-3.2.5-1/net/mac80211/mesh_pathtbl.c: At top level:
/home/mcgrof/tmp/compat-wireless-3.2.5-1/net/mac80211/mesh_pathtbl.c:342:26: error: conflicting types for ‘path_lookup’
include/linux/namei.h:71:12: note: previous declaration of ‘path_lookup’ was here

Although this could sit as a separate patch in compat-wireless it seems
best to just merge upstream.

Cc: Javier Cardona <javier@cozybit.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@frijolero.org>
Acked-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Handle previous allocation failures when freeing device memory
Signed-off-by: NSimon Graham <simon.graham@virtualcomputer.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When not debugging mac80211 code, station state transitions do not need to
show up in the kernel log.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Align with the v2.5.0.0 Ralink RT3572 driver.

Save the EEPROM txmixer_gain values inside the rt2800 driver data structure
and use it throughout the code.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Align with the v2.5.0.0 Ralink RT3572 driver.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Align with the v2.5.0.0 Ralink RT3572 driver.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Align with v2.5.0.0 Ralink RT3572 driver for 2.4GHz band channel switch.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This brings the rt2800 channel switching code for RT3572 closer to the
v2.5.0.0 Ralink RT3572 driver.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The comment states that the field is only used for rt61pci and rt73usb.
However, it is now used by rt2800pci and rt2800usb as well, so the
comment is not correct anymore.

Update the comment to not state any low-level drivers anymore.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Start using the struct rt2x00_dev driver data in rt2800 for the calibration
data.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We are getting more and more fields in struct rt2x00_dev that are
specific to one or two of the low-level drivers. Instead of putting
these fields inside the main structure and thus clobbering all low-level
drivers with these fields, introduce the concept of driver data inside
struct rt2x00_dev, whose size is indicated by the low-level driver and
which can be populated by the low-level driver.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The two orinoco mailing lists on sourceforge were set up many years
ago and are now more or less moribund.  I'd like to shut them down, so
I don't have to keep filtering the spam from them (which is most of
what comes through now).  In preparation, this patch removes the
reference to them from the MAINTAINERS file.  Any remaining discussion
of this approaching obsolete driver can go to the linux-wireless list.
Signed-off-by: NDavid Gibson <hermes@gibson.dropbear.id.au>
Acked-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>