This patch adds support for context switching the MSA vector registers.
These 128 bit vector registers are aliased with the FP registers - an
FP register accesses the least significant bits of the vector register
with which it is aliased (ie. the register with the same index). Due to
both this & the requirement that the scalar FPU must be 64-bit (FR=1) if
enabled at the same time as MSA the kernel will enable MSA & scalar FP
at the same time for tasks which use MSA. If we restore the MSA vector
context then we might as well enable the scalar FPU since the reason it
was left disabled was to allow for lazy FP context restoring - but we
just restored the FP context as it's a subset of the vector context. If
we restore the FP context and have previously used MSA then we have to
restore the whole vector context anyway (see comment in
enable_restore_fp_context for details) so similarly we might as well
enable MSA.

Thus if a task does not use MSA then it will continue to behave as
without this patch - the scalar FP context will be saved & restored as
usual. But if a task executes an MSA instruction then it will save &
restore the vector context forever more.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6431/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch introduces definitions for the MSA control registers and
functions which allow access to both the control & vector registers. If
the toolchain being used to build the kernel includes support for MSA
then this patch will make use of that support & use MSA instructions
directly. However toolchain support for MSA is very new & far from a
point where it can be reasonably expected that everyone building the
kernel uses a toolchain with support. Thus fallbacks using .word
assembler directives are also provided for now as a temporary measure.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6429/
Patchwork: https://patchwork.linux-mips.org/patch/6607/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When saving or restoring scalar FP context we want to access the least
significant 64 bits of each FP register. When the FP registers are 64
bits wide that is trivially the start of the registers value in memory.
However when the FP registers are wider this equivalence will no longer
be true for big endian systems. Define a new set of offset macros for
the least significant 64 bits of each saved FP register within thread
context, and make use of them when saving and restoring scalar FP
context.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6428/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch adds a simple macro to wrap the ext instruction which was
introduced with MIPSR2, and fall back to a shift & and pair for
pre-MIPSR2 CPUs. This will be used in a subsequent patch.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6358/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

CPUs implementing MIPS32 R2 may include a 64-bit FPU, just as MIPS64 CPUs
do. In order to preserve backwards compatibility a 64-bit FPU will act
like a 32-bit FPU (by accessing doubles from the least significant 32
bits of an even-odd pair of FP registers) when the Status.FR bit is
zero, again just like a mips64 CPU. The standard O32 ABI is defined
expecting a 32-bit FPU, however recent toolchains support use of a
64-bit FPU from an O32 MIPS32 executable. When an ELF executable is
built to use a 64-bit FPU a new flag (EF_MIPS_FP64) is set in the ELF
header.

With this patch the kernel will check the EF_MIPS_FP64 flag when
executing an O32 binary, and set Status.FR accordingly. The addition
of O32 64-bit FP support lessens the opportunity for optimisation in
the FPU emulator, so a CONFIG_MIPS_O32_FP64_SUPPORT Kconfig option is
introduced to allow this support to be disabled for those that don't
require it.

Inspired by an earlier patch by Leonid Yegoshin, but implemented more
cleanly & correctly.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paul Burton <paul.burton@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/6154/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

For MIPS R2, use the EI and DI instructions to enable and disable
interrupts.
Signed-off-by: NTomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Use common code from hazards.h instead.
Signed-off-by: NChris Dearman <chris@mips.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Start cleaning 32-bit vs. 64-bit configuration.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!