We were setting RX_FILTER_BEACON even after entering STA mode,
which leads to a lot of unnecessary wakeups.  This should fix the
bug "Ath5k driver has too many interrupts per second at idle" at
http://bugzilla.kernel.org/show_bug.cgi?id=11749.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Take care to handle register 0xa228 exactly as in the HAL released by
Atheros. This change is required to make ath5k work again on my system
since commit 2203d6be (ath5k: Misc hw_reset updates), thus fixing a
regression in 2.6.27 and therefore hopefully eligible for inclusion into
a stable release.

v2: Only overwrite initial register values on later revisions of AR5212
    chips.
v3: Use standard macros to manipulate the register.
Signed-off-by: NElias Oltmanns <eo@nebensachen.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make menuconfig RT2X00 a tristate instead of boolean,
otherwise we do not correctly inherit the mac80211 value
on which RT2X00 depends, and makes it possible to
compile rt2x00 into the kernel while mac80211 is a
module.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Change "mamagement" to "management"
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If somebody sends an invalid beacon/probe response, that can trash the
whole BSS descriptor. The descriptor is, luckily, large enough so that
it cannot scribble past the end of it; it's well above 400 bytes long.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.24-2.6.27, bug present in some form since driver was added (2.6.22)]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Johannes Berg detected this two sparse warnings:

drivers/net/wireless/libertas/cmd.c:609:16: warning: cast to restricted __le16
drivers/net/wireless/libertas/cmd.c:611:16: warning: cast to restricted __le16

... but cmd.minlevel is "s8", so we can access it directly and hope
for the sign-extension-code in the compiler to convert that to the
"s16" type.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes suspend to RAM after by moving
notify_mac out of iwlwifi mutex

http://bugzilla.kernel.org/show_bug.cgi?id=11845Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Tested-by: NCarlos R. Mafra <crmafra2@gmail.com>
Tested-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On Saturday 25 October 2008 10:24:10 Johannes Berg wrote:
> just FYI in case you haven't seen them. the p54 one looks like a genuine
> problem.
>
> drivers/net/wireless/p54/p54common.c: In function ‘p54_parse_eeprom’:
> drivers/net/wireless/p54/p54common.c:325: warning: ‘synth’ may be used uninitialized in this function

There you go. Yes, it is a genuine problem, if the device's eeprom is screwed really up.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After a s2ram / resume cycle, resetting the key cache does not work
unless it is deferred until after the hardware has been reinitialised by
a call to ath5k_hw_reset(). This fixes a regression introduced by
"ath5k: fix suspend-related oops on rmmod".
Signed-off-by: NElias Oltmanns <eo@nebensachen.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a double-free error in p54pci
( http://bugzilla.kernel.org/show_bug.cgi?id=11782 )

Trying to free already-free IRQ 10
Pid: 108, comm: pccardd Not tainted 2.6.27-05577-g0cfd8103-dirty #1
Call Trace:
 [<c01265dc>] free_irq+0xad/0xb9
 [<c01050dd>] dma_generic_alloc_coherent+0x0/0xd7
 [<c01ba8e6>] p54p_stop+0x4a/0x1fa
 [<c01050dd>] dma_generic_alloc_coherent+0x0/0xd7
 [<c02348c5>] p54p_probe+0x23e/0x302

Tested-by: Sean Young
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

free sk_buff with kfree_skb, instead of kree
Signed-off-by: NSergio Luis <sergio@larces.uece.br>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Badness at /home/proski/src/linux-2.6/net/mac80211/rx.c:2200
NIP: c02bc850 LR: c02ab268 CTR: 00000000
REGS: ef01fcc0 TRAP: 0700   Tainted: G        W  (2.6.27-wl)
MSR: 00029032 <EE,ME,IR,DR>  CR: 22004084  XER: 20000000
TASK = c1a58800[1778] 'p54pci' THREAD: ef01e000
[...]
NIP [c02bc850] __ieee80211_rx+0x17c/0x638
LR [c02ab268] ieee80211_tasklet_handler+0x104/0x120
Call Trace:
[ef01fd70] [c1a0c020] 0xc1a0c020 (unreliable)
[ef01fdb0] [c02ab268] ieee80211_tasklet_handler+0x104/0x120
[...]

the problem was that some older cards are mis-identified and didn't support
5GHz rates, while they have the right MAC & Synth chip.

This patch changes the way how p54 decides if it should enable 11a channels
or not.
Reported-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

orinoco_dl_firmware and symbol_dl_mage allocate large local
variables (1K); at least orinoco fails with panic or hung
kernel if 4K stacks is enabled.

Allocate large buffers dynamically at run time.

Tested-By: Andrey Borzenkov <arvidjaar@mail.ru> for Agere case

Signed-off-by: Andrey Borzenkov < arvidjaar@mail.ru>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Based on a patch by Elias Oltmanns, we call ath5k_init in resume even
if we didn't previously open the device.  Besides starting up the
device unnecessarily, this also causes an oops on rmmod because
mac80211 will not invoke ath5k_stop and softirqs are left running after
the module has been unloaded.  Add a new state bit, ATH_STAT_STARTED,
to indicate that we have been started up.
Reported-by: NToralf Förster <toralf.foerster@gmx.de>
Signed-off-by: NElias Oltmanns <eo@nebensachen.de>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that device_create() has been audited, rename things back to the
original call to be sane.

Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The hw_key pointer is used (and obviously NULL) after skb->cb is
memset to 0. This patch grabs the iv_len before the memset call.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NStephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The Belkin F5D7050rev5000de (id 050d:705e) has the Realtek RTL8187B chip
and works with the 2.6.27 driver.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch updates p54usb's device list.
It adds the ID for SMC 2862W-G v2 and marks the
"Spinnaker Proto board" as a first generation device.

Reported-by: <jafg666@gmail.com>
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As I've reported, ath9k currently fails utterly when fragmentation
is enabled. This makes ath9k "support" hardware fragmentation by
not supporting fragmentation at all to avoid the double-free issue.
The patch also changes mac80211 to report errors from the driver
operation to userspace.

That hack in ath9k should be removed once the rate control algorithm
it has is fixed, and we can at that time consider removing the hw
fragmentation support entirely since it's not used by any driver.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Acked-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Below patch removes the following warning during compilation.

drivers/net/wireless/libertas/cmd.c:826: warning: unused variable 'old_channel'

Signed-off-by : Manish Katiyar <mkatiyar@gmail.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A similar problem was highlighted in the orinoco_cs driver by lockdep.
This patch fixes the spectrum_cs driver.
Signed-off-by: NDavid Kilroy <kilroyd@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

[ 6972.562035] =================================
[ 6972.562040] [ INFO: inconsistent lock state ]
[ 6972.562048] 2.6.27-1avb #17
[ 6972.562053] ---------------------------------
[ 6972.562060] inconsistent {in-hardirq-W} -> {hardirq-on-W} usage.
[ 6972.562068] pm-suspend/17062 [HC0[0]:SC0[0]:HE1:SE1] takes:
[ 6972.562076]  (&priv->lock){++..}, at: [<dfd4f05b>] orinoco_cs_resume+0x5b/0xd0 [orinoco_cs]
[ 6972.562122] {in-hardirq-W} state was registered at:
[ 6972.562128]   [<c013ea6b>] __lock_acquire+0x6cb/0x1640
[ 6972.562171]   [<c013fa3c>] lock_acquire+0x5c/0x80
[ 6972.562181]   [<c02f6e39>] _spin_lock_irqsave+0x49/0x80
[ 6972.562210]   [<dfd6425d>] orinoco_interrupt+0x4d/0x16d0 [orinoco]
[ 6972.562257]   [<c015a2b1>] handle_IRQ_event+0x31/0x60
[ 6972.562278]   [<c015b73e>] handle_level_irq+0x6e/0xe0
[ 6972.562291]   [<c0104b20>] do_IRQ+0xb0/0x130
[ 6972.562313]   [<ffffffff>] 0xffffffff
Signed-off-by: NAndrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes ct kill configuration for 5350. Temperature units that
HW expects are in Celsius not in kelvins.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit entitled "p54: Fix sparse warnings" introduced a compile
error on PPC architecture. Thanks to Johannes Berg
<johannes@sipsolutions.net> for reporting this problem.

Signed-off-by: <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When CONFIG_IWLWIFI_DEBUG is not set and CONFIG_IWLWIFI is set,
we get this compilation warning:
/wireless-next-2.6/drivers/net/wireless/iwlwifi/iwl-agn-rs.c: In
function 'rs_free_sta':
/wireless-next-2.6/drivers/net/wireless/iwlwifi/iwl-agn-rs.c:2425:
warning: unused variable 'priv'

This patch fixes it by adding __maybe_unused attribute.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reported by zOOmER.gm@gmail.com to work here:

	http://bugzilla.kernel.org/show_bug.cgi?id=11728Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clean up the various different email addresses of mine listed in the code
to a single current and valid address. As Dave says his network merges
for 2.6.28 are now done this seems a good point to send them in where
they won't risk disrupting real changes.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We were not reporting a status code back ath9k_hw_setpower() failed
during reset so lets correct this.
Reported-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is fucking horribe crap code so nuke it. There I cursed too in a commit log.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes STATUS_CONF_PENDING usage that called from
iwl4965_mac_config internally after scan completed.

It's called anyway from the mac80211 ieee80211_scan_completed():

	if (local->hw_scanning) {
		local->hw_scanning = false;
		if (ieee80211_hw_config(local))
		...
	}
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch moves comment to proper line, it has moved during
code shuffling.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch sets rx_chain bitmap correctly according hw configuration.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clean up the tx status reporting, fix retry counters (short retries are
virtual collisions, not actual retries). Implement multi-rate retry
support.
This also fixes strong throughput fluctuations with rc80211_pid
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adjusts the rate control API to allow multi-rate retry
if supported by the driver. The ieee80211_hw struct specifies how
many alternate rate selections the driver supports.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Free up 2 bytes in skb->cb to be used for multi-rate retry later.
Move iv_len and icv_len initialization into key alloc.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The state field of the rfkill structure was incorrectly initialized to -1, which results in rfkill
issueing a WARN_ON. Fix this by initializing the state field to the proper value as indicated by
the driver.
Signed-off-by: NGertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds the a few lines that went missing in
"p54: 802.11a 5GHz phy support"

Essentially: the rx-code wasn't updated and therefore reported the wrong band,
but more importantly the rate index was off as well, since 802.11a doesn't
allow the "four" 802.11b rates...
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This enables Adaptive Noise Immunity (ANI) on ath9k.
ANI is as algorithm designed to minimize the detrimental
effects of time-varying interferences. This should
help with throughput in noisy environments. To use
ANI we re-enable the MIB interrupt. Since ANI works
on a timer and updates the noise floor we take
advantage of this and also report a non-static noise
floor now to mac80211.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJouni Malinen <Jouni.Malinen@Atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We were trying to hold the wrong spinlock due to a typo
on IEEE80211_BAR_CTL_TID_S's definition. We use this to
compute the tid number and then hold this this tid number's
spinlock.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Part of the cleanup on ath9k -- this was also causing some
annoying compile time warnings.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>