Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

currently ath9k_hw_getchan_noise is not used anywhere
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Processing TSF out of range before RX helps to update beacon
timers so early in the succeeding rx process.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The assumsion is that while processing ath9k tasklet,
interrupts were already disabled and it will be enabled
at the completion of ath9k tasklet. But whenever TSFOOR is raised,
the driver configures the beacon timers after having received a
beacon frame from the AP which inturn enables the interrupts.

Cc: stable@kernel.org
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With AR9003 at about ~ 10 feet from an AP that uses RTS / CTS you
will be able to associate but not not get data through given that
the power for the rates used was set too low. This increases the
power and permits data connectivity at longer distances from
access points when connected with HT40. Without this you will not
get any data through when associated to APs configured in HT40
at about more than 10 feet away.

Cc: stable@kernel.org
Cc: Fiona Cain <fcain@atheros.com>
Cc: Zhen Xie <Zhen.Xie@Atheros.com>
Cc: Kathy Giori <kathy.giori@atheros.com>
Cc: Neha Choksi <neha.choksi@atheros.com>
Cc: Wayne Daniel <wayne.daniel@atheros.com>
Cc: Gaurav Jauhar <gaurav.jauhar@atheros.com>
Cc: Samira Naraghi <samira.naraghi@atheros.com>
CC: Ashok Chennupati <ashok.chennupati@atheros.com>
Cc: Lance Zimmerman <lance.zimmerman@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

At present the noise floor calibration is processed in supported
control and extension chains rather than required chains.
Unnccesarily doing nfcal in all supported chains leads to
invalid nf readings on extn chains and these invalid values
got updated into history buffer. While loading those values
from history buffer is moving the chip to deaf state.

This issue was observed in AR9002/AR9003 chips while doing
associate/dissociate in HT40 mode and interface up/down
in iterative manner. After some iterations, the chip was moved
to deaf state. Somehow the pci devices are recovered by poll work
after chip reset. Raading the nf values in all supported extension chains
when the hw is not yet configured in HT40 mode results invalid values.

Cc: stable@kernel.org
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

when aggregation protection mode is enabled the hardware needs
to send RTS/CTS for each HT frame. Currently its disabled so
remove the unused call backs.
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While draining the txq in flush, the buffers can be
added into the tx queue by tx_tasklet which leads to
unneccesary chip reset.

This issue was originially found with AR9382 and
running heavy uplink udp traffic with higher bandwidth
and doing frequent bgscan.

Cc: stable@kernel.org
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove all the convoluted hacks in the driver and simplify things
by making use of mac80211's LED triggers.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Debugfs file location: <debugfs_mnt>/ieee80211/phy#/ath9k_htc/modal_eeprom
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Debugfs file location: <debugfs_mnt>/ieee80211/phy#/ath9k_htc/base_eeprom
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This callback is used to set the minimum rate for management
frames.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds WMI_BITRATE_MASK_CMDID which can be
used by the set_bitrate_mask() handler.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Bump the firmware version to 1.2
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use ps wrappers before accessing hw registers in btcoex.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Generic timer interrupt was not triggered unless autosleep was
disabled. Since autosleep is enabled in the newer chipsets,
enable generic timer for using with bt coex logic.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move bt_stomp to ath9k_hw and add its support for latest chipsets.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The xpaBiasLvlFreq parameter array is made up of 16 bit words which
aren't byte-swapped like the other 16-bit eeprom parameters are.
It's only used by the AR9160.
Signed-off-by: NAdrian Chadd <adrian@freebsd.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Requesting beacon sync up to configure beacon timers properly
in hw, has be done after doing beacon config with default values.
Setting the flags in beacon config is causing the device to not
enter into network sleep on idle state.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On AR9003 chips, doing three IQ calibrations will possibly cause chip
in stuck state. In noisy environment, chip could receive
a packet during the middle of three calibrations and it causes
the conflict of HW access and the eventual failure. It also
causes IQ calibration outliers which results in poor Tx EVM.

The IQ Cal procedure is after resetting the chip, run IQ cal 3 times
per each cal cycle and find the two closest readings and average of two.
The advantage of running Tx IQ cal more than once is that we can compare
calibration results for the same gain setting over multiple iterations.
Most of the cases the IQ failures were observed after first pass.

For the AR9485 and later chips, Tx IQ Calibration is performed along
with AGC cal. But for pre-AR9485 chips, Tx IQ cal HW has to be separated
from the rest of calibration HW to avoid chip hang. After all
calibrations are done in HW, we can start SW post-processing.
By doing this way, we minimize the SW difference among all chips.

The order of calibration (run IQ cal before other calibration) is also
needed to avoid chip hang for chips before AR9485. This issue was
originally observed with AR9382.

During the issue kernel log was filled with following message
ath: timeout (100000 us) on reg 0xa640: 0x00000001 & 0x00000001 != 0x00000000
ath: timeout (100000 us) on reg 0xa2c4: 0x00158dd9 & 0x00000001 != 0x00000000
ath: Unable to reset channel (2412 MHz), reset status -5
ath: Unable to set channel
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This helped the developers to fix an issue of chip not entering network
sleep during idle state, previously this was only available as a debug
message
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

newer chipsets support auto sleep feature, so remove the
unlikely check which does not seems to help anything
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We should protect hw_pll handler with power save wrappers and
also modularize hw_pll handler properly for better readability.

Also add a debug message to track chip resets on pll hang condition.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no reason why pll work handler should be part of xmit
file. move it to main.c so that reading hw check routines are
all in the same place.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We need not wake up the chip even before mutex lock is acquired and also
that it is required only if we are going to drain the txq. So place the
wrappers accordingly and this change is also useful when there are no
pending frames in the txq as we do not wake up the chip unnecessarily.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

we should program the AR9485 baseband PLL phase shift to 6 and
a redundant setting overwrites the correct value. Remove the
incorrect and unwnated register setting.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The LED gpio is incorrectly programmed for AR9300 and so the led
is not working propelry. AR93xx uses gpio 10 for LED and not the
default.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Hw next tigger time is configured as current_tsf + (timer_period * 10) which
is wrong, it should be current_tsf + timer_period. The wrong hw timer configuration
would cause btcoex related issues.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Set the maximum ampdu size of a station correctly
in the target by using the ampdu_factor.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Register the driver's maximum ampdu subframe limit to mac80211.
* Cleanup the target capabilities structure and fix an endian issue.
* Fix BTCOEX by sending a command to the target when the BT priority
  changes.
* Bump the required firmware version to 1.1
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9340 is a AR9003 family built-in 2x2 wmac of ar934x SOCs. It is single band
in ar9341 SOC and dual band in ar9344/ar9342 SOCs.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>