For non hotplug PCI devices, the system firmware usually configures
CLS correctly.  For pccard devices system firmware can't do it and
Linux PCI layer doesn't do it either.  Unfortunately this leads to
poor performance for certain devices (sata_sil).  Unless MWI, which
requires separate configuration, is to be used, CLS doesn't affect
correctness, so the configuration should be harmless.

This patch makes pci_set_cacheline_size() always built and export it
and make pccard call it during attach.

Please note that some other PCI hotplug drivers (shpchp and pciehp)
also configure CLS on hotplug.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Greg KH <greg@kroah.com>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Axel Birndt <towerlexa@gmx.de>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Till now, CLS has been determined either by arch code or as
L1_CACHE_BYTES.  Only x86 and ia64 set CLS explicitly and x86 doesn't
always get it right.  On most configurations, the chance is that
firmware configures the correct value during boot.

This patch makes pci_init() determine CLS by looking at what firmware
has configured.  It scans all devices and if all non-zero values
agree, the value is used.  If none is configured or there is a
disagreement, pci_dfl_cache_line_size is used.  arch can set the dfl
value (via PCI_CACHE_LINE_BYTES or pci_dfl_cache_line_size) or
override the actual one.

ia64, x86 and sparc64 updated to set the default cls instead of the
actual one.

While at it, declare pci_cache_line_size and pci_dfl_cache_line_size
in pci.h and drop private declarations from arch code.
Signed-off-by: NTejun Heo <tj@kernel.org>
Acked-by: NDavid Miller <davem@davemloft.net>
Acked-by: NGreg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Introduce a new PCI device flag, wakeup_prepared, to prevent PCI
wake-up preparation code from being executed twice in a row for the
same device and for the same purpose.
Reviewed-by: NMatthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

In general a BIOS may goof or we may hotplug in a hotplug controller.
In either case the kernel needs to reserve resources for plugging
in more devices in the future instead of creating a minimal resource
assignment.

We already do this for cardbus bridges I am just adding a variant
for pcie bridges.

v2: Make testing for pcie hotplug bridges based on a flag.

    So far we only set the flag for pcie but a header_quirk
    could easily be added for the non-standard pci hotplug
    bridges.
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Separate out pci_add_dynid() from store_new_id() and export it so that
in-kernel code can add PCI IDs dynamically.  As the function will be
available regardless of HOTPLUG, put it and pull pci_free_dynids()
outside of CONFIG_HOTPLUG.

This will be used by pci-stub to initialize initial IDs via module
param.

While at it, remove bogus get_driver() failure check.
Signed-off-by: NTejun Heo <tj@kernel.org>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Reviewed-by: NGrant Grundler <grundler@parisc-linux.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This is the first of three patches that implement a bit field that PCI
Express device drivers can use to indicate they need a fundamental reset
during error recovery.

By default, the EEH framework on powerpc does what's known as a "hot
reset" during recovery of a PCI Express device.  We've found a case
where the device needs a "fundamental reset" to recover properly.  The
current PCI error recovery and EEH frameworks do not support this
distinction.

The attached patch (courtesy of Richard Lary) adds a bit field to
pci_dev that indicates whether the device requires a fundamental reset
during recovery.

These patches supersede the previously submitted patch that implemented
a fundamental reset bit field.
Signed-off-by: NMike Mason <mmlnx@us.ibm.com>
Signed-off-by: NRichard Lary <rlary@us.ibm.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Background:
Graphic devices are accessed through ranges in I/O or memory space. While most
modern devices allow relocation of such ranges, some "Legacy" VGA devices
implemented on PCI will typically have the same "hard-decoded" addresses as
they did on ISA. For more details see "PCI Bus Binding to IEEE Std 1275-1994
Standard for Boot (Initialization Configuration) Firmware Revision 2.1"
Section 7, Legacy Devices.

The Resource Access Control (RAC) module inside the X server currently does
the task of arbitration when more than one legacy device co-exists on the same
machine. But the problem happens when these devices are trying to be accessed
by different userspace clients (e.g. two server in parallel). Their address
assignments conflict. Therefore an arbitration scheme _outside_ of the X
server is needed to control the sharing of these resources. This document
introduces the operation of the VGA arbiter implemented for Linux kernel.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NTiago Vignatti <tiago.vignatti@nokia.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Some devices allow an individual function to be reset without affecting
other functions in the same device: that's what pci_reset_function does.
For devices that have this support, expose reset attribite in sysfs.

This is useful e.g. for virtualization, where a qemu userspace
process wants to reset the device when the guest is reset,
to emulate machine reboot as closely as possible.
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Since this function should never modify it (saves warnings when called with
const args too).
Signed-off-by: NAlexey Zaytsev <zaytsev@altell.ru>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Other functions use type bool, so use that for pci_enable_wake as well.
Signed-off-by: NFrans Pop <elendil@planet.nl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch enhances the FLR functions:
  1) remove disable_irq() so the shared IRQ won't be disabled.
  2) replace the 1s wait with 100, 200 and 400ms wait intervals
     for the Pending Transaction.
  3) replace mdelay() with msleep().
  4) add might_sleep().
  5) lock the device to prevent PM suspend from accessing the CSRs
     during the reset.
  6) coding style fixes.
Reviewed-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NYu Zhao <yu.zhao@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Based on PCI Express AER specs, a root port might receive multiple
TLP errors while it could only save a correctable error source id
and an uncorrectable error source id at the same time. In addition,
some root port hardware might be unable to provide a correct source
id, i.e., the source id, or the bus id part of the source id provided
by root port might be equal to 0.

The patchset implements the support in kernel by searching the device
tree under the root port.

Patch 1 changes parameter cb of function pci_walk_bus to return a value.
When cb return non-zero, pci_walk_bus stops more searching on the
device tree.
Reviewed-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NZhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Create symbolic link to hotplug driver module in the PCI slot
directory (/sys/bus/pci/slots/<SLOT#>). In the past, we need to load
hotplug drivers one by one to identify the hotplug driver that handles
the slot, and it was very inconvenient especially for trouble shooting.
With this change, we can easily identify the hotplug driver.
Signed-off-by: NTaku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

pci_bus_set_ops changes pci_ops associated with a pci_bus. This can be
used by debug tools such as PCIE AER error injection to fake some PCI
configuration registers.
Acked-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch (as1235) adds an array of PCI power-state names, together
with a simple inline accessor routine.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adds support for PCI Express transaction layer end-to-end CRC checking
(ECRC).  This patch will enable/disable ECRC checking by setting/clearing
the ECRC Check Enable and/or ECRC Generation Enable bits for devices that
support ECRC.

The ECRC setting is controlled by the "pci=ecrc=<policy>" command-line
option. If this option is not set or is set to 'bios", the enable and
generation bits are left in whatever state that firmware/BIOS set them to.
The "off" setting turns them off, and the "on" option turns them on (if the
device supports it).

Turning ECRC on or off can be a data integrity versus performance
tradeoff.  In theory, turning it on will catch more data errors, turning
it off means possibly better performance since CRC does not need to be
calculated by the PCIe hardware and packet sizes are reduced.
Signed-off-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The last in-tree caller of pci_find_slot has been converted, so
let's get rid of this deprecated interface.
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

We should not assign 64bit ranges to PCI devices that only take 32bit
prefetchable addresses.

Try to set IORESOURCE_MEM_64 in 64bit resource of pci_device/pci_bridge
and make the bus resource only have that bit set when all devices under
it support 64bit prefetchable memory.  Use that flag to allocate
resources from that range.
Reported-by: NYannick <yannick.roehlly@free.fr>
Reviewed-by: NIvan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The PCIe ATS capability makes the Endpoint be able to request the
DMA address translation from the IOMMU and cache the translation
in the device side, thus alleviate IOMMU pressure and improve the
hardware performance in the I/O virtualization environment.
Signed-off-by: NYu Zhao <yu.zhao@intel.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch sets up disabled bridges even if buses have already been
added.

pci_assign_unassigned_resources is called after buses are added.
pci_assign_unassigned_resources calls pci_bus_assign_resources.
pci_bus_assign_resources calls pci_setup_bridge to configure BARs of
bridges.

Currently pci_setup_bridge returns immediately if the bus have already
been added. So pci_assign_unassigned_resources can't configure BARs of
bridges that were added in a disabled state; this patch fixes the issue.

On logical hot-add, we need to prevent the kernel from re-initializing
bridges that have already been initialized. To achieve this,
pci_setup_bridge returns immediately if the bridge have already been
enabled.

We don't need to check whether the specified bus is a root bus or not.
pci_setup_bridge is not called on a root bus, because a root bus does
not have a bridge.

The patch adds a new helper function, pci_is_enabled. I made the
function name similar to pci_is_managed. The codes which use
enable_cnt directly are changed to use pci_is_enabled.
Acked-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NYuji Shimada <shimada-yxb@necst.nec.co.jp>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The radeonfb driver needs to program the device's PMCSR directly due
to some quirky hardware it has to handle (see
http://bugzilla.kernel.org/show_bug.cgi?id=12846 for details) and
after doing that it needs to call the platform (usually ACPI) to
finish the power transition of the device.  Currently it uses
pci_set_power_state() for this purpose, however making a specific
assumption about the internal behavior of this function, which has
changed recently so that this assumption is no longer satisfied.
For this reason, introduce __pci_complete_power_transition() that may
be called by the radeonfb driver to complete the power transition of
the device.  For symmetry, introduce __pci_start_power_transition().
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This API is used by the PCI core to rescan a bus and rediscover
newly added devices.

Over time, it is expected that the various PCI hotplug drivers
will migrate to this interface and away from the old
pci_do_scan_bus() interface.
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Introduce pci_is_root_bus helper function. This will help make code
more consistent, as well as prevent incorrect assumptions (such as
pci_bus->self == NULL on a root bus, which is not always true).
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add or remove a Virtual Function after receiving a Migrate In or Out
Request.
Reviewed-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NYu Zhao <yu.zhao@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add or remove the Virtual Function when the SR-IOV is enabled or
disabled by the device driver. This can happen anytime rather than
only at the device probe stage.
Reviewed-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NYu Zhao <yu.zhao@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

If a device has the SR-IOV capability, initialize it (set the ARI
Capable Hierarchy in the lowest numbered PF if necessary; calculate
the System Page Size for the VF MMIO, probe the VF Offset, Stride
and BARs). A lock for the VF bus allocation is also initialized if
a PF is the lowest numbered PF.
Reviewed-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NYu Zhao <yu.zhao@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add the new API pci_enable_msi_block() to allow drivers to
request multiple MSI and reimplement pci_enable_msi in terms of
pci_enable_msi_block.  Ensure that the architecture back ends don't
have to know about multiple MSI.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

drivers/pci/hotplug/fakephp.c: In function 'pci_rescan_bus':
drivers/pci/hotplug/fakephp.c:271: warning: passing argument 1 of 'pci_bus_assign_resources' discards qualifiers from pointer target type
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

drivers/pci/hotplug/fakephp.c:283: warning: passing argument 1 of 'pci_bus_add_devices' discards qualifiers from pointer target type
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Introduce new function pci_msix_table_size() returning the size of
the MSI-X table of given PCI device or 0 if the device doesn't
support MSI-X.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch makes the ROM reading code return an error to user space if
the size of the ROM read is equal to 0.

The patch also emits a warnings if the contents of the ROM are invalid,
and documents the effects of the "enable" file on ROM reading.
Signed-off-by: NTimothy S. Nelson <wayland@wayland.id.au>
Acked-by: NAlex Villacis-Lasso <a_villacis@palosanto.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

There is a problem in our handling of suspend-resume of PCI devices that
many of them have their standard config registers restored with
interrupts enabled and they are put into the full power state with
interrupts enabled as well.  This may lead to the following scenario:
  * an interrupt vector is shared between two or more devices
  * one device is resumed earlier and generates an interrupt
  * the interrupt handler of another device tries to handle it and
    attempts to access the device the config space of which hasn't been
    restored yet and/or which still is in a low power state
  * the system crashes as a result

To prevent this from happening we should restore the standard
configuration registers of all devices with interrupts disabled and we
should put them into the D0 power state right after that.
Unfortunately, this cannot be done using the existing
pci_set_power_state(), because it can sleep.  Also, to do it we have to
make sure that the config spaces of all devices were actually saved
during suspend.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

pcibios_enable_device() and pcibios_disable_device() don't handle
IRQs for devices that have MSI enabled and it should treat the
devices with MSI-X enabled in the same way.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

During an online device reset it may be useful to disable bus-mastering.
pci_disable_device() does that, and far more besides, so is not suitable
for an online reset.

Add pci_clear_master() which does just this.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Reviewed-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The VPD on all devices may not be 32K. Unfortunately, there is no
generic way to find the size, so this adds a simple API hook
to reset it.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Change PCI VPD API which was only used by sysfs to something usable
in drivers.
   * move iteration over multiple words to the low level
   * use conventional types for arguments
   * add exportable wrapper
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch adds pci_common_swizzle(), which swizzles INTx values all the
way up to a root bridge.

This common implementation can replace several architecture-specific
ones.  This should someday be combined with pci_get_interrupt_pin(),
but I left it separate for now to make reviewing easier.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch moves all definitions of the PCI resource names to an 'enum',
and also replaces some hard-coded resource variables with symbol
names. This change eases introduction of device specific resources.
Reviewed-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NYu Zhao <yu.zhao@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This cleanup removes unnecessary argument 'struct resource *res' in
pci_update_resource(), so it takes same arguments as other companion
functions (pci_assign_resource(), etc.).
Signed-off-by: NYu Zhao <yu.zhao@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

It's too large to be inlined.
Acked-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>