The flexcan_start_xmit() function compares the frame length with data
register length to write frame content into data[0] and data[1]
register. Data register length is 4 bytes and frame maximum length is 8
bytes.

Fix the check that compares frame length with 3. Because the register
length is 4.
Signed-off-by: NLuu An Phu <phu.luuan@nxp.com>
Reviewed-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Enable FLEXCAN_QUIRK_BROKEN_PERR_STATE for VF610 to report correct state
transitions.
Tested-by: NMirza Krak <mirza.krak@gmail.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The flexcan IP cores used on MX25 and MX35 do not generate Error Passive
IRQs. Update the IP core overview table in the driver accordingly.
Suggested-by: NZHU Yi (ST-FIR/ENG1-Zhu) <Yi.Zhu5@cn.bosch.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Enable FLEXCAN_QUIRK_BROKEN_WERR_STATE and
FLEXCAN_QUIRK_BROKEN_PERR_STATE for p1010 to report correct state
transitions.
Signed-off-by: NZhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: NMark Jonas <mark.jonas@de.bosch.com>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Enable FLEXCAN_QUIRK_BROKEN_PERR_STATE for i.MX28 to report correct
state transitions, especially to error passive.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NZhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: NMark Jonas <mark.jonas@de.bosch.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Enable FLEXCAN_QUIRK_BROKEN_PERR_STATE for i.MX6 to report correct state
transitions.
Signed-off-by: NZhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: NMark Jonas <mark.jonas@de.bosch.com>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Add FLEXCAN_QUIRK_BROKEN_PERR_STATE for better description of the
missing error passive interrupt quirk.

Error interrupt flooding may happen if the broken error state quirk fix
is enabled. For example, in case there is singled out node on the bus
and the node sends a frame, then error interrupt flooding happens and
will not stop because the node cannot go to bus off. The flooding will
stop after another node connected to the bus again.

If high bitrate configured on the low end system, then the flooding
may causes performance issue, hence, this patch mitigates this by:
1. disable error interrupt upon error passive state transition
2. re-enable error interrupt upon error warning state transition
3. disable/enable error interrupt upon error active state transition
   depends on FLEXCAN_QUIRK_BROKEN_WERR_STATE

In this way, the driver is still able to report correct state
transitions without additional latency. When there are bus problems,
flooding of error interrupts is limited to the number of frames required
to change state from error warning to error passive if the core has
[TR]WRN_INT connected (FLEXCAN_QUIRK_BROKEN_WERR_STATE is not enabled),
otherwise, the flooding is limited to the number of frames required to
change state from error active to error passive.
Signed-off-by: NZhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: NMark Jonas <mark.jonas@de.bosch.com>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Rename FLEXCAN_QUIRK_BROKEN_ERR_STATE to FLEXCAN_QUIRK_BROKEN_WERR_STATE
for better description of the missing [TR]WRN_INT quirk.
Signed-off-by: NZhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: NMark Jonas <mark.jonas@de.bosch.com>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Update state upon any interrupt to report correct state transitions in
case the flexcan core enabled the broken error state quirk fix.
Signed-off-by: NZhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: NMark Jonas <mark.jonas@de.bosch.com>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch fixes the typo "Disble" -> "Disable".
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch switches the imx6 and vf610 based SoCs from the hardware FIFO
to the timestamp based rx offloading.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The flexcan IP core has 64 mailboxes. For now they are configured for
RX as a hardware FIFO. This FIFO has a fixed depth of 6 CAN frames. In
some high load scenarios it turns out thas this buffer is too small.

In order to have a buffer larger than the 6 frames FIFO, this patch adds
support for timestamp based offloading via the generic rx-offload
infrastructure.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

In order to receive RTR frames in the non HW FIFO mode the RSS and EACEN bits
of the reg_ctrl2 have to be activated. As this has no side effect in the FIFO
mode, we do this unconditionally on cores with the reg_ctrl2.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Modern flexcan IP cores support two RX modes. One is using the 6 fames deep
hardware FIFO, the other is using up to 64 mailboxes (in non FIFO mode). For
now only the HW FIFO mode is activated.

In order to make use of the RX mailboxes the individual RX masking feature has
to be activated, otherwise matching mailboxes are overwritten during the
reception process. This however switches on the individual RX masking, which
uses reg_rximr registers for masking.

This patch activates the individual RX masking feature unconditionally and
initializes the mask registers (reg_rximr) with 0x0 == "don't care", which
switches off any filtering.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch converts the flexcan driver to make use of the rx-offload
can_rx_offload_irq_offload_fifo() helper function. The idea is to read
the CAN frames already in the interrupt context, as the depth of the
flexcan HW FIFO is too shallow, resulting in too many missed frames.
During a normal NAPI poll the frames are the pushed into the upper
layers.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch makes the TX mailbox selectable duing runtime. This is a preparation
patch to use of the hardware FIFO selectable via runtime. As the TX mailbox
number is different in HW FIFO and normal mode.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch converts the define FLEXCAN_IFLAG_DEFAULT into the runtime
calculated value priv->reg_imask1_default. This is a preparation patch to make
the TX mailbox selectable during runtime, too.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch changes the flexcan_irq() function to only return
IRQ_HANDLED, if the interrupt really has been handled, otherwise
IRQ_NONE is returned.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch folds in the do_bus_err() function into
flexcan_poll_bus_err().
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch removed the not needed initialisation from the new_state,
rx_state, tx_state variabled.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch converts the rx_errors and tx_errors from int into bool
values, to reflect their actual meaning.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch changes the declaration of the devtype data to const.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch removes the write only member pdata from the struct
flexcan_priv.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch adds some missing register definitions, which are needed in an
upcoming patch.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d303
("net: gro: add a per device gro flush timer")

This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On a imx6ul-pico board the following error is seen during system suspend:

dpm_run_callback(): platform_pm_resume+0x0/0x54 returns -110
PM: Device 2090000.flexcan failed to resume: error -110

The reason for this suspend error is because when the CAN interface is not
active the clocks are disabled and then flexcan_chip_enable() will
always fail due to a timeout error.

In order to fix this issue, only call flexcan_chip_enable/disable()
when the CAN interface is active.

Based on a patch from Dong Aisheng in the NXP kernel.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

As Dan Carpenter reported in http://marc.info/?l=linux-can&m=144793696016187
the assignment of the error location in CAN error messages had some bit wise
overlaps. Indeed the value to be assigned in data[3] is no bitfield but defines
a single value which points to a location inside the CAN frame on the wire.

This patch fixes the assignments for the error locations in error messages.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch defers the writing of the interrupts bits of the CTRL register order
to enables all interrupts atomically at the the of the flexcan_chip_start()
function.
Suggested-by: NTorsten Lang <torsten.lang@uweschneider.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch gives the member of flexcan_priv holding mailboxes a sensible name,
by renaming from "cantxfg" to "mb":

    struct flexcan_priv::cantxfg -> struct flexcan_priv::mb
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch renames the pointer to the mmio address space from "base" to "regs"
and changes the type from "void __iomem *" to "struct flexcan_regs __iomem *".
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch renames the "features" member of struct flexcan_devtype_data to
"quirks". The corresponding defines are renamed too, to reflect what they
actually do.

    FLEXCAN_HAS_V10_FEATURES      -> FLEXCAN_QUIRK_DISABLE_RXFG
    FLEXCAN_HAS_BROKEN_ERR_STATE  -> FLEXCAN_QUIRK_BROKEN_ERR_STATE
    FLEXCAN_HAS_MECR_FEATURES     -> FLEXCAN_QUIRK_DISABLE_MECR
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch changes the order the individual bits of the mcr register in
flexcan_chip_start() are or'ed together to match the datasheet. The inline
documentation is adjusted accordingly.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch removes unused header files from the flexcan driver.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch fixes up the coding style to make checkpatch happier. Some typos are
also fixed.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This message isn't really helpful for the general reader of the kernel
logs, so should not be printed with info level. All other register
programming outputs in the flexcan driver already use the debug level.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch replaces a open coded variant of a "mailbox code" definition by an
existing define, improves code readability.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This is done to mach the abbreviationin of the register in the datasheets.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch adds a short documentation snippet about the mailbox organization as
it's regularly not correct in freescale's datasheets.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Flexcan V10 and newer are able to receive RTR frames in a MB. Older versions
are not. Those should use flexcan in FIFO mode.
Signed-off-by: NDavid Jander <david@protonic.nl>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>