Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 160
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 09 12月, 2009 1 次提交
    • N
      sysfs/cpu: Add probe/release files · 12633e80
      由 Nathan Fontenot 提交于 
      Version 3 of this patch is updated with documentation added to
Documentation/ABI.  There are no changes to any of the C code from v2
of the patch.

In order to support kernel DLPAR of CPU resources we need to provide an
interface to add (probe) and remove (release) the resource from the system.
This patch Creates new generic probe and release sysfs files to facilitate
cpu probe/release.  The probe/release interface provides for allowing each
arch to supply their own routines for implementing the backend of adding
and removing cpus to/from the system.

This also creates the powerpc specific stubs to handle the arch callouts
from writes to the sysfs files.

The creation and use of these files is regulated by the
CONFIG_ARCH_CPU_PROBE_RELEASE option so that only architectures that need the
capability will have the files created.
Signed-off-by: NNathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
      12633e80
  3. 31 10月, 2009 7 次提交
  5. 15 10月, 2009 1 次提交
  7. 02 10月, 2009 4 次提交
  9. 23 9月, 2009 1 次提交
    • D
      gpiolib: allow poll() on value · ff77c352
      由 Daniel Glöckner 提交于 
      Many gpio chips allow to generate interrupts when the value of a pin
changes.  This patch gives usermode application the opportunity to make
use of this feature by calling poll(2) on the /sys/class/gpio/gpioN/value
sysfs file.  The edge to trigger can be set in the edge file in the same
directory.  Possible values are "none", "rising", "falling", and "both".

Using level triggers is not possible with current sysfs since nothing
changes the GPIO value (and the IRQ keeps triggering).  Edge triggering
will "just work".  Note that if there was an event between read() and
poll(), the poll() returns immediately.

Also note that this version only supports true GPIO interrupts.  Some
later patch might be able to synthesize this behavior by timer-driven
polling; some systems seem to need that.

[dbrownell@users.sourceforge.net: align ids to 16 bit ids; whitespace]
Signed-off-by: NDaniel Glöckner <dg@emlix.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      ff77c352
  11. 10 9月, 2009 1 次提交
  13. 29 8月, 2009 4 次提交
  15. 01 8月, 2009 1 次提交
  17. 19 6月, 2009 1 次提交
    • R
      LinuxPPS: core support · eae9d2ba
      由 Rodolfo Giometti 提交于 
      This patch adds the kernel side of the PPS support currently named
"LinuxPPS".

PPS means "pulse per second" and a PPS source is just a device which
provides a high precision signal each second so that an application can
use it to adjust system clock time.

Common use is the combination of the NTPD as userland program with a GPS
receiver as PPS source to obtain a wallclock-time with sub-millisecond
synchronisation to UTC.

To obtain this goal the userland programs shoud use the PPS API
specification (RFC 2783 - Pulse-Per-Second API for UNIX-like Operating
Systems, Version 1.0) which in part is implemented by this patch.  It
provides a set of chars devices, one per PPS source, which can be used to
get the time signal.  The RFC's functions can be implemented by accessing
to these char devices.
Signed-off-by: NRodolfo Giometti <giometti@linux.it>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg KH <greg@kroah.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      eae9d2ba
  19. 17 6月, 2009 1 次提交
  21. 13 6月, 2009 1 次提交
    • A
      ext4: teach the inode allocator to use a goal inode number · 11013911
      由 Andreas Dilger 提交于 
      Enhance the inode allocator to take a goal inode number as a
paremeter; if it is specified, it takes precedence over Orlov or
parent directory inode allocation algorithms.

The extents migration function uses the goal inode number so that the
extent trees allocated the migration function use the correct flex_bg.
In the future, the goal inode functionality will also be used to
allocate an adjacent inode for the extended attributes.

Also, for testing purposes the goal inode number can be specified via
/sys/fs/{dev}/inode_goal.  This can be useful for testing inode
allocation beyond 2^32 blocks on very large filesystems.
Signed-off-by: NAndreas Dilger <adilger@sun.com>
Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>
      11013911
  23. 02 6月, 2009 1 次提交
    • A
      cciss: add cciss driver sysfs entries · 7fe06326
      由 Andrew Patterson 提交于 
      Add sysfs entries to the cciss driver needed for the dm/multipath tools.

A file for vendor, model, rev, and unique_id is added for each logical
drive under directory /sys/bus/pci/devices/<dev>/ccissX/cXdY.  Where X =
the controller (or host) number and Y is the logical drive number.

A link from /sys/bus/pci/devices/<dev>/ccissX/cXdY/block:cciss!cXdY to
/sys/block/cciss!cXdY/device is also created.  A bus is created in
/sys/bus/cciss.  A link is created from the pci ccissX entry to
/sys/bus/cciss/devices/ccissX.  Please consider this for inclusion.
Signed-off-by: NMike Miller <mike.miller@hp.com>
Cc: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
      7fe06326
  25. 29 5月, 2009 1 次提交
  27. 23 5月, 2009 1 次提交
    • M
      block: Export I/O topology for block devices and partitions · c72758f3
      由 Martin K. Petersen 提交于 
      To support devices with physical block sizes bigger than 512 bytes we
need to ensure proper alignment.  This patch adds support for exposing
I/O topology characteristics as devices are stacked.

  logical_block_size is the smallest unit the device can address.

  physical_block_size indicates the smallest I/O the device can write
  without incurring a read-modify-write penalty.

  The io_min parameter is the smallest preferred I/O size reported by
  the device.  In many cases this is the same as the physical block
  size.  However, the io_min parameter can be scaled up when stacking
  (RAID5 chunk size > physical block size).

  The io_opt characteristic indicates the optimal I/O size reported by
  the device.  This is usually the stripe width for arrays.

  The alignment_offset parameter indicates the number of bytes the start
  of the device/partition is offset from the device's natural alignment.
  Partition tools and MD/DM utilities can use this to pad their offsets
  so filesystems start on proper boundaries.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
      c72758f3
  29. 28 4月, 2009 1 次提交
  31. 21 4月, 2009 1 次提交
  33. 14 4月, 2009 1 次提交
  35. 10 4月, 2009 1 次提交
  37. 31 3月, 2009 1 次提交
    • D
      regulator: add get_status() · 853116a1
      由 David Brownell 提交于 
      Based on previous LKML discussions:

 * Update docs for regulator sysfs class attributes to highlight
   the fact that all current attributes are intended to be control
   inputs, including notably "state" and "opmode" which previously
   implied otherwise.

 * Define a new regulator driver get_status() method, which is the
   first method reporting regulator outputs instead of inputs.
   It can report on/off and error status; or instead of simply
   "on", report the actual operating mode.

For the moment, this is a sysfs-only interface, not accessible to
regulator clients.  Such clients can use the current notification
interfaces to detect errors, if the regulator reports them.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>
      853116a1
  39. 21 3月, 2009 5 次提交
  41. 31 3月, 2009 1 次提交
  43. 25 2月, 2009 1 次提交
  45. 19 2月, 2009 1 次提交
  47. 06 2月, 2009 1 次提交