This is a tweak which has been shown to improve performance when
moving away from the AP while working in 80Mhz.
When RS decides to go down to 80MHz SISO MCS0 instead switch to 20MHz MCS4.
Go back to 80MHz MCS1 if RS can sustain 20MHz MCS5.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Clean up variable initialisation slightly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

success_ratio is actually 128 * SR in percentage while
IWL_MVM_RS_SR_NO_DECREASE is 85%. Fix this by using RS_PERCENT().
This bug caused the if branch to be always executed. This in turn
led to always selecting a rate, following a column switch, in which
the expected throughput would exceed the best expected current throughput.
In some scenarios where the success ratio isn't >85% such a rate
could be too aggressive leading us to avoid the new column.
This has the potential of causing sub optimal performance.
Reported-by: NMoshe Harel <moshe.harel@intel.com>
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Indentation was off a bit. Fix it.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This message isn't very useful and creates clutter.
Remove it.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Pretty print the rate full details to ease debugging.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The firmware has always treated these two bits to mean that
powersave is enabled when POWER_SAVE_ENA is set and CAM is
clear; it doesn't use them in any non-combined way.

Therefore, it's pointless to send it two bits, and the API
should be cleaned up. Prepare the driver by removing the CAM
bit and using only POWER_SAVE_ENA to indicate whether PS is
enabled or not.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When enabling a queue, the default SSN is 0.

Allow determining what that SSN should be, if required. This
can happen, for example, if a queue gets reconfigured.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

"DQA" is shorthand for "dynamic queue allocation", with the
idea of allocating queues per-RA/TID on-demand rather than
using shared queues statically allocated per vif. The goal
of this is to enable future features (like GO PM) and to
improve performance measurements of TX traffic.

When RA/TID streams can't be neatly sorted into different AC
queues, DQA allows sharing queues for the same RA. This means
that DQA allows different ACs may reach the same HW queue.

Update the code to allow such queue sharing by having a mapping
between the HW queue and the mac80211 queues using it (as this
could be more than one queue).
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Treat PHY RX specially, since it's actually pretty frequent,
doesn't need all the notication etc. code, and will have a
different handler in future hardware.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Return a proper error when wrong parameters are passed to debugfs
tof_range_request.
Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The command needs to have the AP interfaces BSSID (which corresponds
to its address).
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Make some input formats more natural, e.g. bandwidth and periods
are more natural in decimal than in hexadecimal.
Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Commit ce792918 ("iwlwifi: mvm: add basic Time of Flight (802.11mc
FTM) support") created drivers/net/wireless/iwlwifi/mvm/tof.h with a
broken header guard:

    #ifndef __tof
    #define __tof_h__

    ...

    #endif /* __tof_h__ */

Use __tof_h__ in the first line.
Signed-off-by: NNicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Commit "iwlwifi: mvm: don't ask beacons when AP vif and no
assoc sta" directly called iwl_mvm_mac_ctxt_cmd_ap() to update the
MAC context when adding/removing a station. However, this ignores
the case that the vif is actually a P2P GO.

Fix this by calling iwl_mvm_mac_ctxt_changed() that handles P2P GO
case as well.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For the ADD_STA command, when the flag for aggregation
disabling is set, there is a bitmap indicated what TIDs
are disabling aggregations and what aren't. Currently, by
default, all TIDs allow for aggregations since the value
we begin with is 0.

Change this default value to 0xffff so all TIDs don't
allow aggregations until explicitly turned on.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The formula used in D0i3 should also be used in D3, instead of
the hardcoded value.

Additionally, the formula is actually wrong - if the calculation
yields 0 then 1 should be used instead of disabling entirely.
Also need to add 1 since the firmware needs 3 to skip 2, etc.

To make all this clearer, centralize the calculation into a
single function.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This is a workaround to an OTP bug. In Series 8000 1x1, the OTP
0xA052 defines 2x2 antenna configuration. This workaround overrides
the decision based on HW id and MIMO disabled bit which is correct
in the OTP and set to disabled.
Signed-off-by: NMoshe Harel <moshe.harel@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Move the DTS measurement command and notification from short
command header to the new PHY command group for firmware
supporting the extended command headers.
Signed-off-by: NAviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In order to verify d0i3 flow, add debug print to indicate
d0i3 exit was completed (right after tx was re-enabled),
along with the wakeup reasons.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Recent fw version added assert to make sure wowlan configuration
is configured only when a station is connected.

Change the driver behavior to pass this configuration only
if we indeed have ap station id (i.e. connected).
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The RX API is currently mixed up into the general fw-api.h
file, but we're going to need to extend it significantly in
the future, so move it to its own file.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Remove some unused values from the RX API; these were used
with older firmware API that didn't have the RX energy API,
support for which was removed a long time ago.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Since the driver can never configure the data here, this field
will always be reported as 0 by the firmware. Even if this was
not the case, however, it wouldn't matter since the extra data
would be added beyond the end of the phy_info structure we use
in the driver, so wouldn't harm anything in this code either.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This message is useless - it's in the good case that always
happens so enabling it doesn't really help. Just remove it.
There are other ways to debug this (e.g. tracing) so there's
no need to add a message in the bad case.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

It's possible for an AP interface to be UP but not actually
operating (i.e. not beaconing etc.) - in this case it can't
actually do ToF, so check for it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This flag is set in all supported firmwares.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

This flag is set in all supported firmwares.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

All the supported firmwares have this flag set.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

All the supported firmwares use the new API.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

All the supported firwmares support the new API.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We don't support firmwares that don't use the new API.
This also allows to use all the SCD queues, so increase
the reported number of queues to 31.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

There's obviously no reason to write a NUL-terminating byte into
the debugfs file. Apparently nobody tried to use this from a tool
that doesn't strip NUL bytes though, so we never noticed. Fix it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

If we are in d0i3 when entering suspend, we leave d0i3 so that
mac80211 can call us to remove connections or whatever before going to
suspend.  We do this by calling pm_runtime_resume() early in the slave
transport flow and reactivating it later, when the wiphy suspend flow
runs.

The problem is that we queue a work in order to leave d0i3.  If this
work hasn't run yet when the wiphy suspend flow is called, we have a
race and entering d0i3 fails (because we're still holding the
IWL_MVM_REF_EXIT_WORK reference).

To solve this, simply flush the d0i3_exit_work at the beginning of the
iwl_mvm_suspend() function.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

When in AP mode, we need beacons from other APs for HT protection.
However, when there's no any associated station we will not do
any Tx and thus don't really need beacons. On the other hand, these
beacons will cause a lot of unnecessary wakeups which increase our
power consumption. Handle this by asking FW to pass beacons only when
there's at least one associated station.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

ECHO_CMD is a simple command that can be sent to the
firmware just to check that it is alive.
This command is useful for debug purpose, provide a debugfs
hook to send it.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

When receiving statistics notification there is a field of average energy.
This is defines as signed 8 bit, while FW refers to it as unsigned.
when the energy is higher than 127 this causes in iwl_mvm_stat_iterator
a wrong computation of the signal
     int sig = -stats->general.beacon_filter_average_energy;
resulting in incorrect CQM event (change from low to high).

While at it - update the rest of the fields to the correct type.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

This debugfs entry was implemented just as a proof-of-concept before
the full support for netdetect via cfg80211/mac80211 was implemented.
Now that we have a proper way to enable netdetect from userspace, this
entry is redundant and should be removed to avoid unnecessary
maintenance work.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Add support for the new (bigger) TX power command. This doesn't
actually take advantage of the new capabilities (to set per-chain
TX power limits) but makes the code compatible with newer firmware
images expecting the larger command.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

split long debug messages that may result warning in tracing.

Fixes: 1a84e771 ("iwlwifi: mvm: add debug info to schedule scan complete message.")
Signed-off-by: NAyala Beker <ayala.beker@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>