This is a tweak which has been shown to improve performance when
moving away from the AP while working in 80Mhz.
When RS decides to go down to 80MHz SISO MCS0 instead switch to 20MHz MCS4.
Go back to 80MHz MCS1 if RS can sustain 20MHz MCS5.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Clean up variable initialisation slightly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

As the 3165 device uses the same firmware as 7265-D and currently
all 7000 series (including 3160/3165) use the same API versions
remove IWL3165_UCODE_API_OK and _MIN. We might have to put them
back if firmware support ever splits, but in that case might also
have to add a different MODULE_FIRMWARE statement.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

success_ratio is actually 128 * SR in percentage while
IWL_MVM_RS_SR_NO_DECREASE is 85%. Fix this by using RS_PERCENT().
This bug caused the if branch to be always executed. This in turn
led to always selecting a rate, following a column switch, in which
the expected throughput would exceed the best expected current throughput.
In some scenarios where the success ratio isn't >85% such a rate
could be too aggressive leading us to avoid the new column.
This has the potential of causing sub optimal performance.
Reported-by: NMoshe Harel <moshe.harel@intel.com>
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Indentation was off a bit. Fix it.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This message isn't very useful and creates clutter.
Remove it.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Pretty print the rate full details to ease debugging.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The firmware has always treated these two bits to mean that
powersave is enabled when POWER_SAVE_ENA is set and CAM is
clear; it doesn't use them in any non-combined way.

Therefore, it's pointless to send it two bits, and the API
should be cleaned up. Prepare the driver by removing the CAM
bit and using only POWER_SAVE_ENA to indicate whether PS is
enabled or not.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When enabling a queue, the default SSN is 0.

Allow determining what that SSN should be, if required. This
can happen, for example, if a queue gets reconfigured.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

"DQA" is shorthand for "dynamic queue allocation", with the
idea of allocating queues per-RA/TID on-demand rather than
using shared queues statically allocated per vif. The goal
of this is to enable future features (like GO PM) and to
improve performance measurements of TX traffic.

When RA/TID streams can't be neatly sorted into different AC
queues, DQA allows sharing queues for the same RA. This means
that DQA allows different ACs may reach the same HW queue.

Update the code to allow such queue sharing by having a mapping
between the HW queue and the mac80211 queues using it (as this
could be more than one queue).
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

As the transport will decide how many queues (and MSI-X vectors)
to allocate, add a field to indicate that to the op-mode so it
can size/allocate its own data structures appropriately.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Upcoming hardware will have the ability to do L3 hashing for RSS,
directing data packets (and perhaps some associated metadata and
management notifications) to different MSI-X vectors.

In this case, it makes no sense to go through the full RX dispatch
since it's already known that only a subset of the possibilities
can come in, requiring a new receive method. In addition this must
know which queue the packet was received on.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Treat PHY RX specially, since it's actually pretty frequent,
doesn't need all the notication etc. code, and will have a
different handler in future hardware.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Return a proper error when wrong parameters are passed to debugfs
tof_range_request.
Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The command needs to have the AP interfaces BSSID (which corresponds
to its address).
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Make some input formats more natural, e.g. bandwidth and periods
are more natural in decimal than in hexadecimal.
Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Commit ce792918 ("iwlwifi: mvm: add basic Time of Flight (802.11mc
FTM) support") created drivers/net/wireless/iwlwifi/mvm/tof.h with a
broken header guard:

    #ifndef __tof
    #define __tof_h__

    ...

    #endif /* __tof_h__ */

Use __tof_h__ in the first line.
Signed-off-by: NNicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Commit "iwlwifi: mvm: don't ask beacons when AP vif and no
assoc sta" directly called iwl_mvm_mac_ctxt_cmd_ap() to update the
MAC context when adding/removing a station. However, this ignores
the case that the vif is actually a P2P GO.

Fix this by calling iwl_mvm_mac_ctxt_changed() that handles P2P GO
case as well.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For the ADD_STA command, when the flag for aggregation
disabling is set, there is a bitmap indicated what TIDs
are disabling aggregations and what aren't. Currently, by
default, all TIDs allow for aggregations since the value
we begin with is 0.

Change this default value to 0xffff so all TIDs don't
allow aggregations until explicitly turned on.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Tracing, if disabled at runtime, has very low overhead with
great returns on debugging. It therefore makes sense to have
it enabled by default (if the kernel enables EVENT_TRACING).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The formula used in D0i3 should also be used in D3, instead of
the hardcoded value.

Additionally, the formula is actually wrong - if the calculation
yields 0 then 1 should be used instead of disabling entirely.
Also need to add 1 since the firmware needs 3 to skip 2, etc.

To make all this clearer, centralize the calculation into a
single function.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This is a workaround to an OTP bug. In Series 8000 1x1, the OTP
0xA052 defines 2x2 antenna configuration. This workaround overrides
the decision based on HW id and MIMO disabled bit which is correct
in the OTP and set to disabled.
Signed-off-by: NMoshe Harel <moshe.harel@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Move the DTS measurement command and notification from short
command header to the new PHY command group for firmware
supporting the extended command headers.
Signed-off-by: NAviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In order to verify d0i3 flow, add debug print to indicate
d0i3 exit was completed (right after tx was re-enabled),
along with the wakeup reasons.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Recent fw version added assert to make sure wowlan configuration
is configured only when a station is connected.

Change the driver behavior to pass this configuration only
if we indeed have ap station id (i.e. connected).
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The RX API is currently mixed up into the general fw-api.h
file, but we're going to need to extend it significantly in
the future, so move it to its own file.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Remove some unused values from the RX API; these were used
with older firmware API that didn't have the RX energy API,
support for which was removed a long time ago.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Since the driver can never configure the data here, this field
will always be reported as 0 by the firmware. Even if this was
not the case, however, it wouldn't matter since the extra data
would be added beyond the end of the phy_info structure we use
in the driver, so wouldn't harm anything in this code either.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This message is useless - it's in the good case that always
happens so enabling it doesn't really help. Just remove it.
There are other ways to debug this (e.g. tracing) so there's
no need to add a message in the bad case.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

It's possible for an AP interface to be UP but not actually
operating (i.e. not beaconing etc.) - in this case it can't
actually do ToF, so check for it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This flag is set in all supported firmwares.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

This flag is set in all supported firmwares.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

All the supported firmwares have this flag set.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

All the supported firmwares use the new API.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

All the supported firwmares support the new API.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Current kernel support only one fw name with theoretically only one
fw version located in “firmware/htc_[9271|7010].fw”. Which is ok so far we
have only one fw version (1.3). After we realised new fw 1.4, we faced
compatibility problem which was decided to solve by firmware name and
location:
- new firmware is located now in
	firmware/ath9k_htc/htc_[9271|7010]-1.4.0.fw
- old version 1.3 should be on old place, so old kernel have no issues
	with it.
- new kernels including this patch should be able to try different
	supported (min..max) fw version.
- new kernel should be able to support old fw location too. At least for
	now.

At same time this patch will add new module option which should allow user
to play with development  fw version without replacing stable one. If user
will set “ath9k_htc use_dev_fw=1” module will try to find
firmware/ath9k_htc/htc_[9271|7010]-1.dev.0.fw first and if it fails, use
stable version: for example...1.4.0.fw.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add support for the ethtool rx-frames coalescing parameter which allows
defining the number of RX interrupts per frames received. The RDMA
engine supports a configurable timeout with a resolution of
approximately 8.192 us.

We can no longer enable the BDONE/PDONE interrupts as those would
fire for each packet/buffer received, which would defeat the MBDONE
interrupt purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Configuring the ethtool tx-frames property, which translates into N
packets before a TX interrupt is the simplest configuration scheme
because it requires no locking neither at the softare nor hardware
level, and is completely indepedent from the link speed. Since ethtool
does not allow per-tx queue coalescing parameters, we apply the same
setting to any transmit queue.

We can no longer enable the BDONE/PDONE interrupts as those would fire
for each packet/buffer received, which would defeat the MBDONE interrupt
purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1, but offers
interrupt coalescing when the value is > 1.

Since the HW is configured to generate an interrupt when the ring
becomes emtpy, we have to deny any timeout/timer settings coming from
user-space to indicate we can only generate an interrupt very <N>
packets.

While we are at it, fix the DMA_INTR_THRESHOLD_MASK value which was off
by one bit (0xff vs. 0x1ff).
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove not defined MAC_CR_GMII_EN_ bit from MAC_CR.
Signed-off-by: NWoojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create lan78xx_get_mdix_status() and lan78xx_set_mdix_status() for MDIX control.
Signed-off-by: NWoojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>