The platform devices for omapdss, dss and dispc drivers are always
present, so we can use platform_driver_probe instead of
platform_driver_register.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

For unknown reasons we seem to have a return in each of the omapdss's
uninit functions, which is a void function.

Remove the returns.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The omapdss pdata handling is a mess. This is more evident when trying
to use device tree for DSS, as we don't have platform data anymore in
that case. This patch cleans the pdata handling by:

- Remove struct omap_display_platform_data. It was used just as a
  wrapper for struct omap_dss_board_info.
- Pass the platform data only to omapdss device. The drivers for omap
  dss hwmods do not need the platform data. This should also work better
  for DT, as we can create omapdss device programmatically in generic omap
  boot code, and thus we can pass the pdata to it.
- Create dss functions for get_ctx_loss_count and dsi_enable/disable_pads
  that the dss hwmod drivers can call.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The functions calc_fclk_five_taps() and check_horiz_timing_omap3() use the
function dispc_mgr_get_device() to get the omap_dss_device pointer to which
the manager is connected, the width of the panel is derived from that.

The manager's timing is stored in it's private data in APPLY. This contains
the latest timings applied to the manager. Pass these timings to
dispc_ovl_setup() and use them in the above functions. Remove the function
dispc_mgr_get_device() as it isn't used any more.
Signed-off-by: NArchit Taneja <archit@ti.com>

The pixel clock rate for the TV manager is calculated by checking the device
type connected to the manager, and then requesting the VENC/HDMI interface for
the pixel clock rate.

Remove the use of omap_dss_device pointer from here by checking which interface
generates the pixel clock by reading the DSS_CTRL.VENC_HDMI_SWITCH bit.
Signed-off-by: NArchit Taneja <archit@ti.com>

Create a function dss_mgr_check_timings() which wraps around the function
dispc_mgr_timings_ok(). This is mainly a clean up to hide dispc functions
from interface drivers.

dss_mgr_check_timings() is added in the function dss_mgr_check(), it currently
takes the timings maintained in the omap_dss_device struct. This would be later
replaced by the timings stored in the manager's private data.

Make dss_mgr_check_timings() and dispc_mgr_timings_ok() take a const
omap_video_timings pointer since these functions just check the timings.
Signed-off-by: NArchit Taneja <archit@ti.com>

Fake VSYNC support is a hack and has some bugs in it. It isn't used by any user
of DSS. Remove Fake VSYNC support. For DSI command mode and RFBI panels, a user
of DSS should wait for the completion of a frame by using the panel driver's
sync op.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DISPC_FCLK is incorrectly used as functional clock of DISPC in scaling
calculations. So, DISPC_CORE_CLK replaces as functional clock of DISPC.
DISPC_CORE_CLK is derived from DISPC_FCLK divided by an independent DISPC
divisor LCD.
Signed-off-by: NChandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In OMAP3 DISPC video overlays suffer from some undocumented horizontal position
and timing related limitations leading to SYNCLOST errors. Whenever the image
window is moved towards the right of the screen SYNCLOST errors become
frequent. Checks have been implemented to see that DISPC driver rejects
configuration exceeding above limitations.

This code was successfully tested on OMAP3. This code is written based on code
written by Ville Syrjälä <ville.syrjala@nokia.com> in Linux OMAP kernel. Ville
Syrjälä <ville.syrjala@nokia.com> had added checks for video overlay horizontal
timing and DISPC horizontal blanking length limitations.
Signed-off-by: NChandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In OMAP3 and OMAP4, the DISPC Scaler can downscale an image up to 4 times, and
up to 2 times in OMAP2. However, with predecimation, the image can be reduced
to 16 times by fetching only the necessary pixels in memory. Then this
predecimated image can be downscaled further by the DISPC scaler.

The pipeline is configured to use a burst of size 8 * 128 bits which consists
of 8 mini bursts of 16 bytes each. So, horizontal predecimation more than 16
can lead to complete discarding of such mini bursts. L3 interconnect may
handover the bus to some other initiator and inturn delay the fetching of
pixels leading to underflows. So, maximum predecimation limit is fixed at 16.

Based on the downscaling required, a prior calculation of predecimation values
for width and height of an image is done. Since, Predecimation reduces quality
of an image higher priorty is given to DISPC Scaler for downscaling.

This code was successfully tested on OMAP2, OMAP3 and OMAP4. Horizontal and
vertical predecimation worked fine except for some synclost errors due to
undocumented errata in OMAP3 which are fixed later and skewed images were seen
on OMAP2 and OMAP3 during horizontal predecimation which will be addressed in
the future patches.

This code is based on code written by Lajos Molnar <lajos@ti.com> who had added
predecimation support for NV12/YUV/rotated/SDMA buffers.
Signed-off-by: NChandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Clean up the DISPC manager timings related function by:

- Create a common function to set size for LCD and TV.
- Create a common function to check timings for LCD and TV.
- Add dss params to get the range of manager size.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Currently, a LCD manager's timings is set by dispc_mgr_set_lcd_timings() and TV
manager's timings is set by dispc_set_digit_size(). Use a common function called
dispc_mgr_set_timings() which sets timings for both type of managers.

We finally want the interface drivers to use an overlay manager function to
configure it's timings, having a common DISPC function would make things
cleaner.

For LCD managers, dispc_mgr_set_timings() sets LCD size and blanking values, for
TV manager, it sets only the TV size since blanking values don't exist for TV.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The RFBI driver uses dispc_mgr_set_lcd_size() to set the width and height of
the LCD manager. Replace this to use dispc_mgr_set_lcd_timings(), pass dummy
blanking parameters like done in the DSI driver.

This prevents the need to export dispc_mgr_set_lcd_size(), and use a common
function to set lcd timings.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add missing but supported color formats for GFX pipeline in dss features:
RGBX16-4444, RGBA16-4444 and XRGB16-1555.

In dispc_ovl_set_color_mode():

- Remove unsupported modes on GFX pipeline: YUV2 and UYVY. Replace these by
  missing modes supported by GFX pipelines: RGBX16-4444 and RGBA16-4444.

- Fix swapped modes on VID pipelines: RGBX16-4444 and XRGB16-4444.
Signed-off-by: NLajos Molnar <lajos@ti.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This is only needed when using SRAM for framebuffer,
and the support for SRAM framebuffer is about to get
removed.

Otherwise we cannot move most of plat/io.h to be a local
iomap.h for mach-omap2.

Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

OMAP SRAM can be used as video memory on OMAP1 and 2. However, there
usually is very little SRAM available, thus limiting its use, and no
board supported by the kernel currently uses it.

This patch removes the use of SRAM as video ram for the omapdss driver
to simplify memory handling.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

The calculation of required DISPC_FCLK for downscaling is done by multplying the
pixel clock with an integer factor. This isn't true for OMAP4 where the required
clock is calculated using the exact ratio of downscaling done.

Fix this calculation for OMAP4. Also, do a minor clean up of calc_fclk().
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that dss is using devm_ functions for allocation in probe functions,
small reordering of the allocations allows us to clean up the probe
functions more.

This patch moves "unmanaged" allocations after the managed ones, and
uses plain returns instead of gotos where possible. This lets us remove
a bunch of goto labels, simplifying the probe's error handling.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

omapdss doesn't work properly on system suspend. The problem seems to be
the fact that omapdss uses pm_runtime_put() functions when turning off
the hardware, and when system suspend is in process only sync versions
are allowed.

Using non-sync versions normally and sync versions when suspending would
need rather ugly hacks to convey the information of
suspending/not-suspending to different functions. Optimally the driver
wouldn't even need to care about this, and the PM layer would handle
syncing when suspend is in process.

This patch changes all omapdss's pm_runtime_put calls to
pm_runtime_put_sync. This fixes the suspend problem, and probably the
performance penalty of always using sync versions is negligible.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NKevin Hilman <khilman@ti.com>

The various devm_ functions allocate memory that is released when a driver
detaches.  This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Take fifo merge into use by implementing a rather naive fifo merge
threshold calculation: keep the low threshold always the same, but
increase the high threshold when fifo merge is used.

This should greatly increase the time between pixel data fetches from
SDRAM, as the usable fifo size is much larger. However, it probably
won't help for fifo underflows, as the low threshols is kept the same.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Move fifo threshold calculation into dispc.c, as the thresholds are
really dispc internal thing.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Fifo thresholds are calculated using bytes, but the debug print prints
values in buffer units. Change the prints to use bytes to be in line
with the calculations, and also to print in the same units on all OMAPs.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add feature flag for fifo merge. OMAP2 doesn't contain fifo merge, later
OMAPs do.

dispc_enable_fifomerge() checks for the flag when called, and gives a
WARN if fifo merge is being enabled when it is not supported.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Clock requirements for scaling in OMAP2, OMAP3 and OMAP4 are different. In
OMAP2 and OMAP3 the required clock rate is a function of pixel clock, vertical
downscale ratio and horizontal downscale ratio whereas in OMAP4 it is a
function of pixel clock and horizontal downscale ratio only. Selection of 3-tap
vs 5-tap coefficients depends on clock rate line buffer width in OMAP3 whereas
in OMAP4 it is independent of clock rate and line buffer width. In OMAP2 3-tap
for vertical and 5-tap for horizontal scaling is used. In OMAP4 5-tap is used
both for horizontal and vertical scaling for better performance. Also, the
number and width of line buffers differs in OMAP3 and OMAP4.

So, clock functions have been fined tuned for OMAP3 and support has been added
added for OMAP4. This code has been tested on OMAP2, OMAP3 and OMAP4, and
scaling issues due to clock errors have been resolved.
Signed-off-by: NChandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The FIR coefficients present in kernel are being updated to new coefficients
consisting of 24 coefficient tables, with 12 each for 3 tap and 5 tap scenario,
which are chosen on the basis of DISPC up/downsampling filters M value. M is
the inverse of low pass cut off frequency of the sampling filter. For vertical
scaling 3 tap or 5 tap tables are used based on the clock rate and width of
the line buffer whereas in OMAP2 3 tap is always used. For horizontal scaling
however 5 tap tables are always used.

New coefficients and the corresponding logic have been tested on OMAP2, OMAP3
and OMAP4. Horizontal and vertical scaling worked fine except for some 3 tap
vs 5 tap issue during vertical upscaling and clock failing issues which is
acknowledged in the next patch. Vertical upscaling was found to perform better
under 5 taps. The 24 coefficient tables have been moved to another file
dispc_coefs.c for proper maintainance.

This code is written based on code written by Lajos Molnar <lajos@ti.com> in
Android Kernel for scaling. Lajos Molnar <lajos@ti.com> had fine tuned the FIR
coefficient selection process and reduced outliness and blockiness around
images when upscaling more than 2 times.
Signed-off-by: NChandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The dispc's error handler tries to disable all outputs when OCP_ERR
happens. However, the code doesn't check if there actually is a display
on each particular output, nor if there's a driver for the display. This
may lead to NULL pointer reference.
Signed-off-by: NRob Clark <rob@ti.com>
[tomi.valkeinen@ti.com: added patch description]
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add dispc_mgr_get_framedone_irq() which returns the irq number for
FRAMEDONE for the given channel.

Note that the function returns always 0 for DIGIT channel, even if OMAP4
does have FRAMEDONE_TV interrupt. The reason for this is that this
function is currently used only to track manual updates, and thus
FRAMEDONE_TV is not needed.

If there's need in the future to also get the FRAMEDONE_TV this needs
revisiting. However, as FRAMEDONE_TV doesn't exist on OMAP2/3, the use
of this function for that purpose needs some extra code to handle the
OMAP2/3 case.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add dispc_mgr_get_vsync_irq() which returns the irq number for vsync on
the given channel.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Remove unused functions:

dispc_mgr_get_default_color
dispc_mgr_get_trans_key
dispc_mgr_trans_key_enabled
dispc_mgr_alpha_fixed_zorder_enabled
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Change manager configuration to be similar to overlay configuration by
creating dispc_mgr_setup() which takes omap_overlay_manager_info as
parameter.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Overlay channel is configured with ovl_setup, with all the other overlay
attriutes. This patch separates overlay channel setup so that we can
later configure the channel only when needed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Overlay FIFO thresholds are configured with ovl_setup, with all the
other overlay attributes. This patch separates FIFO threshold setup so
that we can later configure FIFO thresholds only when needed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Overlay out_width/height are set to 0 when scaling is not used by the
users of omapdss. Currently ovl_setup() expects the caller of
ovl_setup() to convert those zero values to width or height.

This patch makes ovl_setup() accept zero values for out_width/height,
making calling ovl_setup() a bit simpler as the overlay_info can be
just passed to this function without modifications.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Make dispc_ovl_set_fifo_threshold() public so that later patches can
handle overlay fifo configuration.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Make dispc_ovl_set_channel_out() public so that later patches can handle
changing overlay's manager.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Flush posted write in _enable_lcd_out() and _enable_digit_out(). This
ensures the the lcd/digit bit is written before the code starts waiting
for interrupts about enabling/disabling the output.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Current code calculates scaling factors for video overlays even when the
overlays are not scaled. Change the code to skip calculations when not
scaling.

This optimizes the code a bit, but also fixes a problem when configuring
an overlay for a disabled display: if the display is disabled we don't
necessarily know the pixel clock used when the display is enabled, and
in some cases (like HDMI) the pixel clock is set to zero until a proper
video mode is set later. A wrong pixel clock will mess up the
scaling calculations, causing an error like:

omapdss DISPC error: failed to set up scaling, required fclk rate = 0
Hz, current fclk rate = 170666666 Hz

A proper fix would be to check later whether the clocks are enough for the
scaling, at the point when the overlay or display is actually enabled,
but this patch removes the problem for now.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Add zorder support on OMAP4, this feature allows deciding the visibility order
of the overlays based on the zorder value provided as an overlay info parameter
or a sysfs attribute of the overlay object.

Use the overlay cap OMAP_DSS_OVL_CAP_ZORDER to determine whether zorder is
supported for the overlay or not. Use dss feature FEAT_ALPHA_FREE_ZORDER
if the caps are not available.

Ensure that all overlays that are enabled and connected to the same manager
have different zorders. Swapping zorders of 2 enabled overlays currently
requires disabling one of the overlays.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>