- 09 7月, 2014 1 次提交
-
-
由 Eugenia Emantayev 提交于
In 40GE we can't use the default bw units for set ratelimit (100 Mbps) since the max is 255*100 Mbps = 25 Gbps (not suited for 40GE), thus we need 1 Gbps units. But for 10GE 1 Gbps units might be too bruit so we use the following solution. For user set ratelimit <= 25 Gbps: use 100 Mbps units * user_ratelimit (* 10). For user set ratelimit > 25 Gbps: use 1 Gbps units * user_ratelimit. For user set unlimited ratelimit (0 Gbps): use 1 Gbps units * MAX_RATELIMIT_DEFAULT (57) Note: any value > 58 will damage the FW ratelimit computation, so we allow a max and any higher value will be pulled down to 57. Signed-off-by: NSagi Grimberg <sagig@mellanox.com> Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com> Signed-off-by: NAmir Vadai <amirv@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 03 7月, 2014 1 次提交
-
-
由 Amir Vadai 提交于
IRQ affinity notifier can only have a single notifier - cpu_rmap notifier. Can't use it to track changes in IRQ affinity map. Detect IRQ affinity changes by comparing CPU to current IRQ affinity map during NAPI poll thread. CC: Thomas Gleixner <tglx@linutronix.de> CC: Ben Hutchings <ben@decadent.org.uk> Fixes: 2eacc23c ("net/mlx4_core: Enforce irq affinity changes immediatly") Signed-off-by: NAmir Vadai <amirv@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 03 6月, 2014 1 次提交
-
-
由 Jiri Kosina 提交于
Modify the various routines used to allocate memory resources which serve QPs in mlx4 to get an input GFP directive. Have the Ethernet driver to use GFP_KERNEL in it's QP allocations as done prior to this commit, and the IB driver to use GFP_NOIO when the IB verbs IB_QP_CREATE_USE_GFP_NOIO QP creation flag is provided. Signed-off-by: NMel Gorman <mgorman@suse.de> Signed-off-by: NJiri Kosina <jkosina@suse.cz> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
- 02 6月, 2014 2 次提交
-
-
由 David S. Miller 提交于
This reverts commit 70a640d0. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Atias 提交于
The “affinity hint” mechanism is used by the user space daemon, irqbalancer, to indicate a preferred CPU mask for irqs. Irqbalancer can use this hint to balance the irqs between the cpus indicated by the mask. We wish the HCA to preferentially map the IRQs it uses to numa cores close to it. To accomplish this, we use cpumask_set_cpu_local_first(), that sets the affinity hint according the following policy: First it maps IRQs to “close” numa cores. If these are exhausted, the remaining IRQs are mapped to “far” numa cores. Signed-off-by: NYuval Atias <yuvala@mellanox.com> Signed-off-by: NAmir Vadai <amirv@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 5月, 2014 3 次提交
-
-
由 Jack Morgenstein 提交于
This commit adds the sysfs interface for enabling QP0 on VFs for selected VF/port. By default, no VFs are enabled for QP0 operation. To enable QP0 operation on a VF/port, under /sys/class/infiniband/mlx4_x/iov/<b:d:f>/ports/x there are two new entries: - smi_enabled (read-only). Indicates whether smi is currently enabled for the indicated VF/port - enable_smi_admin (rw). Used by the admin to request that smi capability be enabled or disabled for the indicated VF/port. 0 = disable, 1 = enable. The requested enablement will occur at the next reset of the VF (e.g. driver restart on the VM which owns the VF). Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
由 Jack Morgenstein 提交于
This commit adds the infrastructure for enabling selected VFs to operate SMI (QP0) MADs without restriction. Additionally, for these enabled VFs, their QP0 proxy and tunnel QPs are MLX QPs. As such, they operate over VL15. Therefore, they are not affected by "credit" problems or changes in the VLArb table (which may shut down VL0). Non-enabled VFs may only create UD proxy QP0 qps (which are forced by the hypervisor to send packets using the q-key it assigns and places in the qp-context). Thus, non-enabled VFs will not pose a security risk. The hypervisor discards any privileged MADs it receives from these non-enabled VFs. By default, all VFs are NOT enabled, and must explicitly be enabled by the administrator. The sysfs interface which operates the VF enablement infrastructure is provided in the next commit. Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
由 Jack Morgenstein 提交于
Currently, VFs in SRIOV VFs are denied QP0 access. The main reason for this decision is security, since Subnet Management Datagrams (SMPs) are not restricted by network partitioning and may affect the physical network topology. Moreover, even the SM may be denied access from portions of the network by setting management keys unknown to the SM. However, it is desirable to grant SMI access to certain privileged VFs, so that certain network management activities may be conducted within virtual machines instead of the hypervisor. This commit does the following: 1. Create QP0 tunnel QPs for all VFs. 2. Discard SMI mads sent-from/received-for non-privileged VFs in the hypervisor MAD multiplex/demultiplex logic. SMI mads from/for privileged VFs are allowed to pass. 3. MAD_IFC wrapper changes/fixes. For non-privileged VFs, only host-view MAD_IFC commands are allowed, and only for SMI LID-Routed GET mads. For privileged VFs, there are no restrictions. This commit does not allow privileged VFs as yet. To determine if a VF is privileged, it calls function mlx4_vf_smi_enabled(). This function returns 0 unconditionally for now. The next two commits allow defining and activating privileged VFs. Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
- 23 5月, 2014 1 次提交
-
-
由 Amir Vadai 提交于
use_prio was added as part of an infrastructure for running FCoE in A0 mode. FCoE didn't get into Mellanox Upstream driver, and when it will, it won't be using A0 steering mode. Therefore we can safely deprecate this module parameter without hurting any existing user. CC: Carol Soto <clsoto@linux.vnet.ibm.com> Signed-off-by: NAmir Vadai <amirv@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 15 5月, 2014 1 次提交
-
-
由 Yuval Atias 提交于
During heavy traffic, napi is constatntly polling the complition queue and no interrupt is fired. Because of that, changes to irq affinity are ignored until traffic is stopped and resumed. By registering to the irq notifier mechanism, and forcing interrupt when affinity is changed, irq affinity changes will be immediatly enforced. Signed-off-by: NYuval Atias <yuvala@mellanox.com> Signed-off-by: NAmir Vadai <amirv@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 3月, 2014 2 次提交
-
-
由 Or Gerlitz 提交于
Add implementation for the add/del vxlan port ndo calls, using the CONFIG_DEV firmware command. Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Or Gerlitz 提交于
Introduce the CONFIG_DEV firmware command which we will use to configure the UDP port assumed by the firmware for the VXLAN offloads. Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 21 3月, 2014 3 次提交
-
-
由 Matan Barak 提交于
Adds support for N-Port VFs, this includes: 1. Adding support in the wrapped FW command In wrapped commands, we need to verify and convert the slave's port into the real physical port. Furthermore, when sending the response back to the slave, a reverse conversion should be made. 2. Adjusting sqpn for QP1 para-virtualization The slave assumes that sqpn is used for QP1 communication. If the slave is assigned to a port != (first port), we need to adjust the sqpn that will direct its QP1 packets into the correct endpoint. 3. Adjusting gid[5] to modify the port for raw ethernet In B0 steering, gid[5] contains the port. It needs to be adjusted into the physical port. 4. Adjusting number of ports in the query / ports caps in the FW commands When a slave queries the hardware, it needs to view only the physical ports it's assigned to. 5. Adjusting the sched_qp according to the port number The QP port is encoded in the sched_qp, thus in modify_qp we need to encode the correct port in sched_qp. Signed-off-by: NMatan Barak <matanb@mellanox.com> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Matan Barak 提交于
This patch adds the following utils: 1. Convert slave_id -> VF 2. Get the active ports by slave_id 3. Convert slave's port to real port 4. Get the slave's port from real port 5. Get all slaves that uses the i'th real port 6. Get all slaves that uses the i'th real port exclusively Signed-off-by: NMatan Barak <matanb@mellanox.com> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Matan Barak 提交于
Adds the required data structures to support VFs with N (1 or 2) ports instead of always using the number of physical ports. Signed-off-by: NMatan Barak <matanb@mellanox.com> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 13 3月, 2014 4 次提交
-
-
由 Jack Morgenstein 提交于
Since there is no connection between the MAC/VLAN and the GID when using IP-based addressing, the proxy QP1 (running on the slave) must pass the source-mac, destination-mac, and vlan_id information separately from the GID. Additionally, the Host must pass the remote source-mac and vlan_id back to the slave, This is achieved as follows: Outgoing MADs: 1. Source MAC: obtained from the CQ completion structure (struct ib_wc, smac field). 2. Destination MAC: obtained from the tunnel header 3. vlan_id: obtained from the tunnel header. Incoming MADs 1. The source (i.e., remote) MAC and vlan_id are passed in the tunnel header to the proxy QP1. VST mode support: For outgoing MADs, the vlan_id obtained from the header is discarded, and the vlan_id specified by the Hypervisor is used instead. For incoming MADs, the incoming vlan_id (in the wc) is discarded, and the "invalid" vlan (0xffff) is substituted when forwarding to the slave. Signed-off-by: NMoni Shoua <monis@mellanox.co.il> Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jack Morgenstein 提交于
The GIDs are statically distributed, as follows: PF: gets 16 GIDs VFs: Remaining GIDS are divided evenly between VFs activated by the driver. If the division is not even, lower-numbered VFs get an extra GID. For an IB interface, the number of gids per guest remains as before: one gid per guest. Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jack Morgenstein 提交于
For IB transport, the host determines the slave GIDs. For ETH (RoCE), however, the slave's GID is determined by the IP address that the slave itself assigns to the ETH device used by RoCE. In this case, the slave must be able to write its GIDs to the HCA gid table (at the GID indices that slave "owns"). This commit adds processing for the SET_PORT_GID_TABLE opcode modifier for the SET_PORT command wrapper (so that slaves may modify their GIDS for RoCE). Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jack Morgenstein 提交于
This requires the following modifications: 1. Fix build_mlx4_header to properly fill in the ETH fields 2. Adjust mux and demux QP1 flow to support RoCE. This commit still assumes only one GID per slave for RoCE. The commit enabling multiple GIDs is a subsequent commit, and is done separately because of its complexity. Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 15 1月, 2014 2 次提交
-
-
由 Matan Barak 提交于
This patch add the support for Ethernet L2 attributes in the verbs/cm/cma structures. When dealing with L2 Ethernet, we should use smac, dmac, vlan ID and priority in a similar manner that the IB L2 (and the L4 PKEY) attributes are used. Thus, those attributes were added to the following structures: * ib_ah_attr - added dmac * ib_qp_attr - added smac and vlan_id, (sl remains vlan priority) * ib_wc - added smac, vlan_id * ib_sa_path_rec - added smac, dmac, vlan_id * cm_av - added smac and vlan_id For the path record structure, extra care was taken to avoid the new fields when packing it into wire format, so we don't break the IB CM and SA wire protocol. On the active side, the CM fills. its internal structures from the path provided by the ULP. We add there taking the ETH L2 attributes and placing them into the CM Address Handle (struct cm_av). On the passive side, the CM fills its internal structures from the WC associated with the REQ message. We add there taking the ETH L2 attributes from the WC. When the HW driver provides the required ETH L2 attributes in the WC, they set the IB_WC_WITH_SMAC and IB_WC_WITH_VLAN flags. The IB core code checks for the presence of these flags, and in their absence does address resolution from the ib_init_ah_from_wc() helper function. ib_modify_qp_is_ok is also updated to consider the link layer. Some parameters are mandatory for Ethernet link layer, while they are irrelevant for IB. Vendor drivers are modified to support the new function signature. Signed-off-by: NMatan Barak <matanb@mellanox.com> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
由 Matan Barak 提交于
This patch adds support for allocating IB UD QPs that we can steer traffic from. We introduce a new firmware command FLOW_STEERING_IB_UC_QP_RANGE and a capability bit. This command isn't supported for VFs. Signed-off-by: NMatan Barak <matanb@mellanox.com> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
- 01 1月, 2014 1 次提交
-
-
由 Or Gerlitz 提交于
Add the low-level device commands and definitions used for TCP/IP HW offloads of tunneled/vxlan traffic which are supported by the ConnectX3-pro NIC. This is done through the following elements: - read tunneling device caps in QUERY_DEV_CAP - add helper function to do SET_PORT for tunneling - add DMFS VXLAN steering rule definitions - add CQE and WQE checksum offload field definitions Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 20 12月, 2013 1 次提交
-
-
由 Hadar Hen Zion 提交于
Add the infrastructure needed to support ndo_get_phys_port_id which allows users to identify to which physical port a net-device is connected to by reading a unique port id. This will work for VFs and PFs. The driver uses a new device capability - phys_port_id, The PF driver reads the port phys_port_id from Firmware and stores it. The VF driver reads the port phys_port_id from the PF using QUERY_FUNC_CAP command. Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com> Signed-off-by: NAmir Vadai <amirv@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 08 11月, 2013 2 次提交
-
-
由 Eugenia Emantayev 提交于
For each RX/TX ring and its CQ, allocation is done on a NUMA node that corresponds to the core that the data structure should operate on. The assumption is that the core number is reflected by the ring index. The affected allocations are the ring/CQ data structures, the TX/RX info and the shared HW/SW buffer. For TX rings, each core has rings of all UPs. Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.com> Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com> Reviewed-by: NHadar Hen Zion <hadarh@mellanox.com> Signed-off-by: NAmir Vadai <amirv@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eugenia Emantayev 提交于
This is done to optimize FW/HW access to host memory. Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.com> Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com> Reviewed-by: NHadar Hen Zion <hadarh@mellanox.com> Signed-off-by: NAmir Vadai <amirv@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 05 11月, 2013 3 次提交
-
-
由 Jack Morgenstein 提交于
This is step #1 for implementing SRIOV resource quotas for VFs. Quotas are implemented per resource type for VFs and the PF, to prevent any entity from simply grabbing all the resources for itself and leaving the other entities unable to obtain such resources. Resources which are allocated using quotas: QPs, CQs, SRQs, MPTs, MTTs, MAC, VLAN, and Counters. The quota system works as follows: Each entity (VF or PF) is given a max number of a given resource (its quota), and a guaranteed minimum number for each resource (starvation prevention). For QPs, CQs, SRQs, MPTs and MTTs: 50% of the available quantity for the resource is divided equally among the PF and all the active VFs (i.e., the number of VFs in the mlx4_core module parameter "num_vfs"). This 50% represents the "guaranteed minimum" pool. The other 50% is the "free pool", allocated on a first-come-first-serve basis. For each VF/PF, resources are first allocated from its "guaranteed-minimum" pool. When that pool is exhausted, the driver attempts to allocate from the resource "free-pool". The quota (i.e., max) for the VFs and the PF is: The free-pool amount (50% of the real max) + the guaranteed minimum For MACs: Guarantee 2 MACs per VF/PF per port. As a result, since we have only 128 MACs per port, reduce the allowable number of VFs from 64 to 63. Any remaining MACs are put into a free pool. For VLANs: For the PF, the per-port quota is 128 and guarantee is 64 (to allow the PF to register at least a VLAN per VF in VST mode). For the VFs, the per-port quota is 64 and the guarantee is 0. We assume that VGT VFs are trusted not to abuse the VLAN resource. For Counters: For all functions (PF and VFs), the quota is 128 and the guarantee is 0. In this patch, we define the needed structures, which are added to the resource-tracker struct. In addition, we do initialization for the resource quota, and adjust the query_device response to use quotas rather than resource maxima. As part of the implementation, we introduce a new field in mlx4_dev: quotas. This field holds the resource quotas used to report maxima to the upper layers (ib_core, via query_device). The HCA maxima of these values are passed to the VFs (via QUERY_HCA) so that they may continue to use these in handling QPs, CQs, SRQs and MPTs. Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jack Morgenstein 提交于
Use of vlan_index created problems unregistering vlans on guests. In addition, tools delete vlan by tag, not by index, lets follow that. Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jack Morgenstein 提交于
The functions mlx4_register_vlan, mlx4_unregister_vlan, mlx4_register_mac, mlx4_unregister_mac all made illegal use of the out_param in multifunc mode to pass the port number. The firmware spec specifies that the port number should be passed in bits 8..15 of the input-modifier field for ALLOC_RES and FREE_RES (sections 20.15.1 and 20.15.2). For MAC register/unregister, this patch contains workarounds so that guests running previous kernels continue to work on a new Hypervisor, and guests running the new kernel will continue to work on old hypervisors. Vlan registeration capability is still not operational in multifunction mode, since the vlan wrapper functions are not implemented in this patch. Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 18 10月, 2013 1 次提交
-
-
由 Or Gerlitz 提交于
Small code cleanup: 1. change MLX4_DEV_CAP_FLAGS2_REASSIGN_MAC_EN to MLX4_DEV_CAP_FLAG2_REASSIGN_MAC_EN 2. put MLX4_SET_PORT_PRIO2TC and MLX4_SET_PORT_SCHEDULER in the same union with the other MLX4_SET_PORT_yyy Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NAmir Vadai <amirv@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 8月, 2013 1 次提交
-
-
由 Hadar Hen Zion 提交于
Implement ib_create_flow() and ib_destroy_flow(). Translate the verbs structures provided by the user to HW structures and call the MLX4_QP_FLOW_STEERING_ATTACH/DETACH firmware commands. On the ATTACH command completion, the firmware provides a 64-bit registration ID, which is placed into struct mlx4_ib_flow that wraps the instance of struct ib_flow which is retuned to caller. Later, this reg ID is used for detaching that flow from the firmware. Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
- 03 8月, 2013 1 次提交
-
-
由 Joe Perches 提交于
It's convenient to have ethernet mac addresses use ETH_ALEN to be able to grep for them a bit easier and also to ensure that the addresses are __aligned(2). Add #include <linux/if_ether.h> as necessary. Signed-off-by: NJoe Perches <joe@perches.com> Acked-by: NMauro Carvalho Chehab <m.chehab@samsung.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 7月, 2013 1 次提交
-
-
由 Yevgeny Petrilin 提交于
This commit adds new firmware command and new firmware event. The firmware raises the MLX4_EVENT_TYPE_OP_REQUIRED event in order to signal the driver it needs to perform an administrative operation throughout the MLX4_CMD_GET_OP_REQ command. At the moment the supported operation is adding/removing multicast entries which are used by the firmware for handling NCSI traffic in B0 steering mode. Also, had to swap the order of mlx4_init_mcg_table() and mlx4_init_eq_table() to make sure that driver will get events only after resources are initialized to handle it. Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.com> Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.com> Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com> Signed-off-by: NAmir Vadai <amirv@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 02 7月, 2013 1 次提交
-
-
由 Jack Morgenstein 提交于
Within VST mode, enable modifying the vlan and/or qos for a VF without requiring unbind/rebind. This requires firmware which supports the UPDATE_QP command. (If the command is not available, we fall back to requiring unbind/bind to activate these changes). To avoid race conditions with modify-qp on QPs that are affected by update-qp, this operation is performed on the comm_wq. If the update operation succeeds for all the necessary QPs, a vlan_unregister is performed for the abandoned vlan id. Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 27 4月, 2013 2 次提交
-
-
由 Rony Efraim 提交于
Add ndo_set_vf_spoofchk support Signed-off-by: NRony Efraim <ronye@mellanox.com> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Rony Efraim 提交于
Add support to ndo_set_vf_vlan in the driver. Once this call is used the vport is considered to be in VST mode. In this mode, the PPF driver configures Ethernet QPs created by this VF to use this vlan id and priority. Currently RoCE isn't supported on that mode. The special values of VID=4095 or VID=0,UP=0 are considered as VGT. Signed-off-by: NRony Efraim <ronye@mellanox.com> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 25 4月, 2013 5 次提交
-
-
由 Hadar Hen Zion 提交于
Re-arrange some of code which fills DMFS HW structures so we can use it from within the core driver and from the IB driver too, e.g when verbs DMFS structures are transformed into mlx4 hardware structs. Also, add struct mlx4_flow_handle struct which will be of use by the DMFS verbs flow in the IB driver. Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
由 Hadar Hen Zion 提交于
Some of struct mlx4_net_trans_rule_hw_ctrl fields were packed into u32 and accessed through bit field operations. Expose and access them directly as u8 or u16. Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
由 Hadar Hen Zion 提交于
Change struct mlx4_net_trans_rule_hw_eth :: vlan_id name to vlan_tag Change struct mlx4_net_trans_rule_hw_ib :: r_u_qpn name to l3_qpn The patch doesn't introduce any functional change or API change towards the firmware. Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
由 Hadar Hen Zion 提交于
Align the names used by enum mlx4_net_trans_promisc_mode with the actual firmware specification. The patch doesn't introduce any functional change or API change towards the firmware. Remove MLX4_FS_PROMISC_FUNCTION_PORT which isn't of use. Add new enums MLX4_FS_{UC/MC}_SNIFFER as a preparation step for sniffer support. Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
由 Hadar Hen Zion 提交于
Move flow steering HW structures to be on the public mlx4 include directory, as a pre-step for the mlx4 IB driver to use them too. Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-