For eMMC 5.0 compliant device, firmware version is stored in ext_csd.
Report firmware as a 64bit hexa decimal. Vendor can use hexa or ascii
string to report firmware version.
Also add FFU related EXT_CSD register and note if the device is FFU capable.
Signed-off-by: NGwendal Grignou <gwendal@chromium.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The same tuning block exists in the dw_mmc h.c and sdhci-msm.c
files. Move these into mmc.c so that they can be shared across
drivers.
Reported-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Replace ext_csd "enhanced_area_en" attribute by
 "partition_setting_completed". It was used whether or
 not enhanced user area is defined and without checks of
 EXT_CSD_PARTITION_SETTING_COMPLETED bit.
Signed-off-by: NGrégory Soutadé <gsoutade@neotion.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch adds HS400 mode support for eMMC5.0 device.  HS400 mode is high
speed DDR interface timing from HS200.  Clock frequency is up to 200MHz
and only 8-bit bus width is supported. In addition, tuning process of
HS200 is required to synchronize the command response on the CMD line
because CMD input timing for HS400 mode is the same as HS200 mode.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: NJackey Shen <jackey.shen@amd.com>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Current implementation for bus speed mode selection is too
complicated. This patch is to simplify the codes and remove
some duplicate parts.

The following changes are including:
* Adds functions for each mode selection(HS, HS-DDR, HS200 and etc)
* Rearranged the mode selection sequence with supported device type
* Adds maximum speed for HS200 mode(hs200_max_dtr)
* Adds field definition for HS_TIMING of EXT_CSD
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

Device types which are supported by both host and device can be
identified when EXT_CSD is read. There is no need to check host's
capability anymore.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

This patch adds packed command feature of eMMC4.5.  The maximum number
for packing read (or write) is offered and exception event relevant to
packed command which is used for error handling is enabled. If host
wants to use this feature, MMC_CAP2_PACKED_CMD should be set.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: NMaya Erez <merez@codeaurora.org>
Reviewed-by: NSubhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: NNamjae Jeon <linkinjeon@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Following JEDEC standard, if the mmc supports RPMB partition,
a new interface is created and exposed via /dev/block.
Users will be able to access RPMB partition using standard
mmc IOCTL commands.
Signed-off-by: NAlex Macro <alex.macro@stericsson.com>
Signed-off-by: NLoic Pallardy <loic.pallardy@stericsson.com>
Reviewed-by: NNamjae Jeon <linkinjeon@gmail.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NJohan Rudholm <johan.rudholm@stericsson.com>
Acked-by: NKrishna Konda <kkonda@codeaurora.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Enable eMMC background operations (BKOPS) feature.

If URGENT_BKOPS is set after a response, note that BKOPS are required.
Immediately run BKOPS if required.  Read/write operations should be
requested during BKOPS(LEVEL-1), then issue HPI to interrupt the
ongoing BKOPS and service the foreground operation.
(This patch only controls the LEVEL2/3.)

When repeating the writing 1GB data, at a certain time, performance is
decreased.  At that time, card triggers the Level-3 or Level-2.  After
running bkops, performance is recovered.

Future considerations:
 * Check BKOPS_LEVEL=1 and start BKOPS in a preventive manner.
 * Interrupt ongoing BKOPS before powering off the card.
 * How do we get BKOPS_STATUS value (periodically send ext_csd command)?
 * If using periodic bkops, also consider runtime_pm control.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKonstantin Dorfman <kdorfman@codeaurora.org>
Reviewed-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Current implementation decides the card type exclusively. Even though
eMMC device can support both HS200 and DDR mode, card type will be
set only for HS200. If the host doesn't support HS200 but has DDR
capability, then DDR mode can't be selected.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

MMC-4.5 data tag feature will be used to store the file system meta-data
in the tagged region of eMMC. This will improve the write and subsequent
read transfer time for the meta data.
Signed-off-by: NSaugata Das <saugata.das@linaro.org>
Tested-by: NVenkatraman S <svenkatr@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds the support of the HS200 bus speed for eMMC 4.5 devices.
The eMMC 4.5 devices have support for 200MHz bus speed. The function
prototype of the tuning function is modified to handle the tuning
command number which is different in sd and mmc case.
Signed-off-by: NGirish K S <girish.shivananjappa@linaro.org>
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Enable boot partitions to be read-only locked until next power on via
a sysfs entry. There will be one sysfs entry for each boot partition:

/sys/block/mmcblkXbootY/ro_lock_until_next_power_on

Each boot partition is locked by writing 1 to its file.
Signed-off-by: NJohan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: NJohn Beckett <john.beckett@stericsson.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

HPI command is defined in eMMC4.41.
This feature is important for eMMC4.5 devices.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds cache feature of eMMC4.5 Spec.
If device supports cache capability, host can utilize some specific
operations.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

In the v4.5, there's no secure erase & trim support.
Instead it supports the sanitize feature.
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds support for the power off notify feature, available in
eMMC 4.5 devices. If the host has support for this feature, then the
mmc core will notify the device by setting the POWER_OFF_NOTIFICATION
byte in the extended csd register with a value of 1 (POWER_ON).

For suspend mode short timeout is used, whereas for the normal poweroff
long timeout is used.
Signed-off-by: NGirish K S <girish.shivananjappa@linaro.org>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

EXT_CSD[248] includes the default maximum timeout for CMD6.
This field is added at eMMC4.5 Spec. And it can be used for default
timeout except for some operations which don't define the timeout
(i.e. background operation, sanitize, flush cache) in eMMC4.5 Spec.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

It allows gerneral purpose partitions in MMC Device.  And I try to simply
make mmc_blk_alloc_parts using mmc_part structure suggested by Andrei
Warkentin.  After patching, we see general purpose partitions like this:
> cat /proc/partitions
          179 0 847872 mmcblk0
          179 192 4096 mmcblk0gp3
          179 160 4096 mmcblk0gp2
          179 128 4096 mmcblk0gp1
          179 96  1052672 mmcblk0gp0
          179 64  1024 mmcblk0boot1
          179 32  1024 mmcblk0boot0
Signed-off-by: NNamjae Jeon <linkinjeon@gmail.com>
Acked-by: NAndrei Warkentin <awarkentin@vmware.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds the power class selection feature available for mmc
versions 4.0 and above.  During the enumeration stage before switching
to the lower data bus, check if the power class is supported for the
current bus width. If the power class is available then switch to the
power class and use the higher data bus. If power class is not supported
then switch to the lower data bus in a worst case.
Signed-off-by: NGirish K S <girish.shivananjappa@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

eMMC's may have a hardware reset line.  This patch provides a
host controller operation to implement hardware reset and
a function to reset and reinitialize the card.  Also, for MMC,
the reset is always performed before initialization.

The host must set the new host capability MMC_CAP_HW_RESET
to enable hardware reset.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

If the MMC_SEND_STATUS command is not successful, we should not return
a zero status word, but instead allow the caller to know positively
that an error occurred.

Convert the open-coded get_card_status() to use the helper function,
and provide definitions for the card state field.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NPawel Moll <pawel.moll@arm.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Standardize the checks for multiple MMC header file inclusion,
including adding comments to terminating #endif's, and fixing
one incorrect comment.
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NChris Ball <cjb@laptop.org>

CMD23-prefixed instead of open-ended multiblock transfers
have a performance advantage on some MMC cards.
Signed-off-by: NAndrei Warkentin <andreiw@motorola.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Host Controller needs tuning during initialization to operate SDR50
and SDR104 UHS-I cards. Whether SDR50 mode actually needs tuning is
indicated by bit 45 of the Host Controller Capabilities register.
A new command CMD19 has been defined in the Physical Layer spec
v3.01 to request the card to send tuning pattern.

We enable Buffer Read Ready interrupt at the very begining of tuning
procedure, because that is the only interrupt generated by the Host
Controller during tuning. We program the block size to 64 in the
Block Size register. We make sure that DMA Enable and Multi Block
Select in the Transfer Mode register are set to 0 before actually
sending CMD19. The tuning block is sent by the card to the Host
Controller using DAT lines, so we set Data Present Select (bit 5) in
the Command register. The Host Controller is responsible for doing
the verfication of tuning block sent by the card at the hardware
level. After sending CMD19, we wait for Buffer Read Ready interrupt.
In case we don't receive an interrupt after the specified timeout
value, we fall back on fixed sampling clock by setting Execute
Tuning (bit 6) and Sampling Clock Select (bit 7) of Host Control2
register to 0. Before exiting the tuning procedure, we disable Buffer
Read Ready interrupt and re-enable other interrupts.

Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: NArindam Nath <arindam.nath@amd.com>
Reviewed-by: NPhilip Rakity <prakity@marvell.com>
Tested-by: NPhilip Rakity <prakity@marvell.com>
Acked-by: NZhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Allows device MMC boot partitions to be accessed. MMC partitions are
treated effectively as separate block devices on the same MMC card.
Signed-off-by: NAndrei Warkentin <andreiw@motorola.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Allows reliable writes to be used for MMC writes. Reliable writes are used
to service write REQ_FUA/REQ_META requests. Handles both the legacy and
the enhanced reliable write support in MMC cards.
Signed-off-by: NAndrei Warkentin <andreiw@motorola.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

uBoot sometimes leaves eMMC pointing to the private boot partition.
Ensure we always start looking at the user partition.
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Signed-off-by: NBruce Clemens <bpclemens@marvell.com>
Signed-off-by: NMark F. Brown <markb@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Enhanced area feature is a new feature defined in eMMC4.4 standard. This
user data area provides higher performance/reliability, at the expense
of using twice the effective media space due to the area using SLC.

The MMC driver now reads out the enhanced area offset and size and adds
them to the device attributes in sysfs. Enabling the enhanced area can
only be done once, and should be done in manufacturing. To use this
feature, bit ERASE_GRP_DEF should also be set.

Documentation/ABI/testing/sysfs-devices-mmc describes the two new
attributes.
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Reviewed-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some old MMC devices fail with the 4/8 bits the driver tries to use
exclusively.  This patch adds a test for the given bus setup and falls
back to the lower bit mode (until 1-bit mode) when the test fails.

[Major rework and refactoring by tiwai]
[Quirk addition and many fixes by prakity]
Signed-off-by: NAries Lee <arieslee@jmicron.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Tested-by: NPhilip Rakity <prakity@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add support for Dual Data Rate MMC cards as defined in the 4.4
specification.
Signed-off-by: NHanumath Prasad <hanumath.prasad@stericsson.com>
Cc: linux-mmc@vger.kernel.org
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Tested-by Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

SD/MMC cards tend to support an erase operation.  In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.

SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.

"erase_size" is the minimum size, in bytes, of an erase operation.  For
MMC, "erase_size" is the erase group size reported by the card.  Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector.  For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.

SD/MMC cards can erase an arbitrarily large area up to and
including the whole card.  When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:

    1. A single erase command will make all other I/O on the card
       wait.  This is not a problem if the whole card is being erased, but
       erasing one partition will make I/O for another partition on the
       same card wait for the duration of the erase - which could be a
       several minutes.

    2. To be able to inform the user of erase progress.

    3. The erase timeout becomes too large to be very useful.
       Because the erase timeout contains a margin which is multiplied by
       the size of the erase area, the value can end up being several
       minutes for large areas.

"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.

For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.

For SD, "preferred_erase_size" is the allocation unit size specified by
the card.

"preferred_erase_size" is in bytes.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Acked-by: NJens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The eMMC spec 4.4 and 4.3 + additional feature chips has CSD structure
version 3 and version 3 have to check the CSD_STRUCTURE byte in the
EXT_CSD register.

Also fix EXT_CSD revision message.

[akpm@linux-foundation.org: fix comment, per Chris Ball]
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In the extended CSD register the CARD_TYPE is an 8-bit value of which the
upper 6 bits were reserved in JEDEC specifications prior to version 4.4.
In version 4.4 two of the reserved bits were designated for identifying
support for the newly added High-Speed Dual Data Rate.  Unfortunately the
mmc_read_ext_csd() function required that the reserved bits be zero
instead of ignoring them as it should.

This patch makes mmc_read_ext_csd() ignore the CARD_TYPE bits that are
reserved or not yet supported.  It also stops the function jumping to the
end as though an error occurred, when it is only warns that the CARD_TYPE
bits (that it does interpret) are invalid.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

According to the standard, the SWITCH command should be followed by a
SEND_STATUS command to check for errors.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Acked-by: NMatt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for the new MMC command SLEEP_AWAKE.
Signed-off-by: NJarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Acked-by: NMatt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch removes a CVS tag that wasn't updated for a long time.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Teach the MMC/SD/SDIO system headers that some hosts use SPI mode

 - New host capabilities and status bits
    * MMC_CAP_SPI, with mmc_host_is_spi() test
    * mmc_host.use_spi_crc flag

 - SPI-specific declarations:
    * Response types, MMC_RSP_SPI_R*
    * Two SPI-only commands
    * Status bits used native to SPI:  R1_SPI_*, R2_SPI_*

 - Fix a few (unrelated) whitespace bugs in the headers.

 - Reorder a few mmc_host fields, removing several bytes of padding

None of these changes affect current code.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Make sure we do not try to parse a structure we do not
understand.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Move protocol operations and definitions into their own files
in an effort to separate protocol handling and bus
arbitration more clearly.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>