Spinlock should be taken before checking for tp->hw_stats.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After Power-on-reset, the 5719's TX DMA length registers may contain
uninitialized values and cause TX DMA to stall.  Check for invalid
values and set a register bit to flush the TX channels.  The bit
needs to be turned off after the DMA channels have been flushed.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The workaround was mis-applied to all 5719 and 5720 chips.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

to prevent PHY access conflict with APE firmware.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

the driver sees wether the dev_seeq pointer is having a error that can be
read by using the PTR_ERR, and returns it at error case, other wise 0 at
success case.

the PTR_RET does the same thing, and use PTR_RET instead of redoing the
code of PTR_RET
Signed-off-by: NDevendra Naga <develkernel412222@gmail.com>
Acked-by: NDavid Howells <dhowells@redhat.com>
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

casting the void pointer is redundant (Documentation/CodingStyle)
Signed-off-by: NDevendra Naga <develkernel412222@gmail.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fills the net_device vlan_features with the proper hardware features,
thus, improving the vlan interface performance.

With the patch applied, I can see around 148% improvement on a TCP_STREAM test,
from 3.5 Gb/s to 8.7 Gb/s. On TCP_RR, I see a 11% improvement, from 18k
to 20. The CPU utilization is almost the same on both cases, from the comparison
above.
Signed-off-by: NBreno Leitao <brenohl@br.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The problem is that we call this with a spin lock held.  The call tree
is:
	kaweth_start_xmit() holds kaweth->device_lock.
	-> kaweth_async_set_rx_mode()
	   -> kaweth_control()
	      -> kaweth_internal_control_msg()

The kaweth_internal_control_msg() function is only called from
kaweth_control() which used GFP_ATOMIC for its allocations.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pch_gbe_xmit_frame skb->len verification was incorrect in vlan case
causing bogus transfer length errors.  One correction could be:
    offset = skb->protocol == htons(ETH_P_8021Q) ? 0 : 4;
    if (unlikely(skb->len > (adapter->hw.mac.max_frame_size - offset)))
However, this verification is not necessary, so remove it.
Signed-off-by: NAndy Cress <andy.cress@us.kontron.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds extra cleaning to the pch_gbe_clean_tx routine to avoid
transmit timeouts on some BCM PHYs that have different timing.
Also update the DRV_VERSION to 1.01, and show it.
Signed-off-by: NAndy Cress <andy.cress@us.kontron.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An extended ping test with 6 vlans resulted in a driver oops with a
netdev transmit timeout.
Fix WATCHDOG_TIMEOUT to be more like e1000e at 5 * HZ, to avoid
unnecessary transmit timeouts.
Signed-off-by: NAndy Cress <andy.cress@us.kontron.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch resolves a "BUG: unable to handle kernel paging request at ..."
oops while dumping packet data. The issue occurs with IOMMU enabled due to
the address provided by phys_to_virt().

This patch makes use of skb->data on Tx and the virtual address of the pages
allocated for Rx.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

info->control.sta and control.vif may only be dereferenced during the
drv_tx call otherwise could lead to use-after-free bugs.
Signed-off-by: NThomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Wrong pointer variable is being used to parse the rss hash from
receive completions leading to corrupted rss_hash values filled into skb.
Signed-off-by: NSarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RFS filter id can't have the special value RPS_NO_FILTER,
need to skip it when allocating id's.

CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It prevents ring_size being set to a too small value.
Reported-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When attempting to disable ethernet autonegation via ethtool,
the pch_gpe driver will set software reset bit of PHY chip, But
control register of PHY chip of FRI2 will reenable ethernet autonegation.
Signed-off-by: NWei Yang <w90p710@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "WIZnet devices" config option should depend on HAS_IOMEM as
all wiznet drivers require it as well.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are seeing an oops in be_get_fw_log_level on ppc64 where we walk
off the end of memory.

commit 941a77d5 (be2net: Fix to allow get/set of debug levels in
the firmware.) requires byteswapping of num_modes and num_modules.

Cc: stable@vger.kernel.org # 3.5+
Signed-off-by: NAnton Blanchard <anton@samba.org>
Acked-by: NSathya Perla <sperla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the mlx4 drivers don't have the necessary callbacks to
implement EEH errors detection and recovery, so the PCI layer uses the
probe and remove callbacks to try to recover the device after an error on
the bus. However, these callbacks have race conditions with the internal
catastrophic error recovery functions, which will also detect the error
and this can cause the system to crash if both EEH and catas functions
try to reset the device.

This patch adds the necessary error recovery callbacks and makes sure
that the internal catastrophic error functions will not try to reset the
device in such scenarios. It also adds some calls to
pci_channel_offline() to suppress reads/writes on the bus when the slot
cannot accept I/O operations so we prevent unnecessary accesses to the
bus and speed up the device removal.
Signed-off-by: NKleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: NShlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The clk patches added code to get and enable clocks in the
respective driver probe functions.  If the probe function failed
for some reason after enabling the clock, the clock was not
disabled again in many cases.
Signed-off-by: NSimon Baatz <gmbnomis@gmail.com>
Signed-off-by: NAndrew Lumm <andrew@lunn.ch>

Tag Ericsson NCM devices as WWAN modems, since they almost certainly all
are.  This way userspace clients know that the device requires further
setup on the AT-capable serial ports before connectivity is available.
Signed-off-by: NDan Williams <dcbw@redhat.com>

Reported-by: <rucsoftsec@gmail.com>
Resolves-bug: http://bugzilla.kernel.org/show_bug?44441Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will ensure correct value is returned in case the port list is empty.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Reported-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In boards with 4-ports, Tx LPI statistics were gathered incorrectly.
This patch guarantees that each pmf will only query its own port for
these statistics.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 036dafa2.

First it appears in bisection, then reverting it solves the usual
netdev watchdog problem for different people. I don't have a proper
fix yet so get rid of it.
Bisected-and-reported-by: NAlex Villacís Lasso <a_villacis@palosanto.com>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 57840 boards come in two flavours: 2 x 20G and 4 x 10G.
To better differentiate between the two flavours, a separate device ID
was assigned to each.
The silicon default value is still the currently supported 57840 device ID
(0x168d), and since a user can damage the nvram (e.g., 'ethtool -E')
the driver will still support this device ID to allow the user to amend the
nvram back into a supported configuration.

Notice this patch contains lines longer than 80 characters (strings).
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change niu_rbr_fill() to use unlikely() to check niu_rbr_add_page() return
value to be consistent with the rest of the checks after niu_rbr_add_page()
calls in this file.
Signed-off-by: NShuah Khan <shuah.khan@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix Neptune ethernet driver to check dma mapping error after map_page()
interface returns.
Signed-off-by: NShuah Khan <shuah.khan@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add pm_runtime support to the TI Davinci EMAC driver.

CC: Sekhar Nori <nsekhar@ti.com>
CC: Kevin Hilman <khilman@ti.com>
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The '#include <mach/mux.h>' line in davinci_emac.c
causes a compile error because that header file
isn't found.  It turns out that the #include isn't
needed because the driver isn't (and shoudn't be)
touching the mux anyway, so remove it.

CC: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Let vhost-net utilize zero copy tx when used with tun.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tun xmit is actually receive of the internal tun
socket. Orphan the frags same as we do for normal rx path.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver now offers software transmit time stamping, so it should
advertise that fact via ethtool. Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>

Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver now offers software transmit time stamping, so it should
advertise that fact via ethtool. Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>

Cc: Willem de Bruijn <willemb@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver now offers software transmit time stamping, so it should
advertise that fact via ethtool. Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>

Cc: Willem de Bruijn <willemb@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver now offers software transmit time stamping, so it should
advertise that fact via ethtool. Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix printk format warnings in drivers/net/wimax/i2400m:

drivers/net/wimax/i2400m/control.c: warning: format '%zu' expects argument of type 'size_t', but argument 4 has type 'ssize_t' [-Wformat]
drivers/net/wimax/i2400m/control.c: warning: format '%zu' expects argument of type 'size_t', but argument 5 has type 'ssize_t' [-Wformat]
drivers/net/wimax/i2400m/usb-fw.c: warning: format '%zu' expects argument of type 'size_t', but argument 4 has type 'ssize_t' [-Wformat]

I don't see these warnings on x86.  The warnings that are quoted above
are from Geert's kernel build reports.
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc:	Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc:	linux-wimax@intel.com
Cc:	wimax@linuxwimax.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>