Spinlock should be taken before checking for tp->hw_stats.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After Power-on-reset, the 5719's TX DMA length registers may contain
uninitialized values and cause TX DMA to stall.  Check for invalid
values and set a register bit to flush the TX channels.  The bit
needs to be turned off after the DMA channels have been flushed.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The workaround was mis-applied to all 5719 and 5720 chips.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

to prevent PHY access conflict with APE firmware.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The test for the fillempty condition was wrong in one place.
Changed the variable to the right boolean type.
Signed-off-by: NKarsten Keil <keil@b1-systems.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

the driver sees wether the dev_seeq pointer is having a error that can be
read by using the PTR_ERR, and returns it at error case, other wise 0 at
success case.

the PTR_RET does the same thing, and use PTR_RET instead of redoing the
code of PTR_RET
Signed-off-by: NDevendra Naga <develkernel412222@gmail.com>
Acked-by: NDavid Howells <dhowells@redhat.com>
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

casting the void pointer is redundant (Documentation/CodingStyle)
Signed-off-by: NDevendra Naga <develkernel412222@gmail.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fills the net_device vlan_features with the proper hardware features,
thus, improving the vlan interface performance.

With the patch applied, I can see around 148% improvement on a TCP_STREAM test,
from 3.5 Gb/s to 8.7 Gb/s. On TCP_RR, I see a 11% improvement, from 18k
to 20. The CPU utilization is almost the same on both cases, from the comparison
above.
Signed-off-by: NBreno Leitao <brenohl@br.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The problem is that we call this with a spin lock held.  The call tree
is:
	kaweth_start_xmit() holds kaweth->device_lock.
	-> kaweth_async_set_rx_mode()
	   -> kaweth_control()
	      -> kaweth_internal_control_msg()

The kaweth_internal_control_msg() function is only called from
kaweth_control() which used GFP_ATOMIC for its allocations.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These devices are set to 640x480 by firmware, switch them to 800x600@60
so that the graphical installer can run on remote console.

Reported by IBM during SLES10 SP2 beta testing:

https://bugzilla.novell.com/show_bug.cgi?id=461002
LTC50817
Signed-off-by: NOlaf Hering <olaf@aepfle.de>
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

at default case of switch we return with out unlocking the mutex.
Signed-off-by: NDevendra Naga <develkernel412222@gmail.com>
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>

Use the error codes from the lower levels instead of -ENODEV.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NJan-Simon Möller <jansimon.moeller@gmx.de>
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>

This can return without freeing the bl_work struct.  Also there was no
check for allocation failure.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NJan-Simon Möller <jansimon.moeller@gmx.de>
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>

pch_gbe_xmit_frame skb->len verification was incorrect in vlan case
causing bogus transfer length errors.  One correction could be:
    offset = skb->protocol == htons(ETH_P_8021Q) ? 0 : 4;
    if (unlikely(skb->len > (adapter->hw.mac.max_frame_size - offset)))
However, this verification is not necessary, so remove it.
Signed-off-by: NAndy Cress <andy.cress@us.kontron.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds extra cleaning to the pch_gbe_clean_tx routine to avoid
transmit timeouts on some BCM PHYs that have different timing.
Also update the DRV_VERSION to 1.01, and show it.
Signed-off-by: NAndy Cress <andy.cress@us.kontron.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An extended ping test with 6 vlans resulted in a driver oops with a
netdev transmit timeout.
Fix WATCHDOG_TIMEOUT to be more like e1000e at 5 * HZ, to avoid
unnecessary transmit timeouts.
Signed-off-by: NAndy Cress <andy.cress@us.kontron.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch resolves a "BUG: unable to handle kernel paging request at ..."
oops while dumping packet data. The issue occurs with IOMMU enabled due to
the address provided by phys_to_virt().

This patch makes use of skb->data on Tx and the virtual address of the pages
allocated for Rx.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Parity Setting value is reverse.
E.G. In case of setting ODD parity, EVEN value is set.
This patch inverts "if" condition.
Signed-off-by: NTomoya MORINAGA <tomoya.rohm@gmail.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Rx Error interrupt(E.G. parity error) is not enabled.
So, when parity error occurs, error interrupt is not occurred.
As a result, the received data is not dropped.

This patch adds enable/disable rx error interrupt code.
Signed-off-by: NTomoya MORINAGA <tomoya.rohm@gmail.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Otherwise we fall back to the wrong value.

Reported-by: <dcb314@hotmail.com>
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=44091Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit acfa747b introduced the TTY_HUPPING flag to distinguish
closed TTY from currently closing ones. The test in tty_set_ldisc
still remained pointing at the old flag. This causes pppd to
sometimes lapse into uninterruptible sleep when killed and
restarted.
Signed-off-by: NShachar Shemesh <shachar@liveu.tv>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

pch_uart_interrupt() takes priv->port.lock which leads to two recursive
spinlock calls if low_latency==1 or CONFIG_PREEMPT_RT_FULL=y (one
otherwise):

pch_uart_interrupt
  spin_lock_irqsave(priv->port.lock, flags)
  case PCH_UART_IID_RDR_TO (data ready)
  handle_rx_to
    push_rx
      tty_port_tty_get
        spin_lock_irqsave(&port->lock, flags) <--- already hold this lock
        ...
      tty_flip_buffer_push
        ...
        flush_to_ldisc
          spin_lock_irqsave(&tty->buf.lock)
            spin_lock_irqsave(&tty->buf.lock)
            disc->ops->receive_buf(tty, char_buf)
              n_tty_receive_buf
                tty->ops->flush_chars()
                uart_flush_chars
                  uart_start
                    spin_lock_irqsave(&port->lock) <--- already hold this lock

Avoid this by using a dedicated lock to protect the eg20t_port structure
and IO access to its membase. This is more consistent with the 8250
driver.  Ensure priv->lock is always take prior to priv->port.lock when
taken at the same time.

V2: Remove inadvertent whitespace change.
V3: Account for oops_in_progress for the private lock in
    pch_console_write().

Note: Like the 8250 driver, if a printk is introduced anywhere inside
      the pch_console_write() critical section, the kernel will hang
      on a recursive spinlock on the private lock. The oops case is
      handled by using a trylock in the oops_in_progress case.
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>
CC: Tomoya MORINAGA <tomoya.rohm@gmail.com>
CC: Feng Tang <feng.tang@intel.com>
CC: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

pm_restore_console() is called from the suspend/resume path, and this
calls vt_move_to_console(), which calls vt_waitactive().

There's a race in this path which causes the process which requests the
suspend to sleep indefinitely waiting for an event which already
happened:

P1                                      P2
 vt_move_to_console()
  set_console()
    schedule_console_callback()
  vt_waitactive()
    check n == fg_console +1
                                       console_callback()
                                         switch_screen()
                                         vt_event_post() // no waiters

    vt_event_wait() // forever

Fix the race by ensuring we're registered for the event before we check
if it's already completed.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds a "compatible" string for the new 8250 UART type PORT_LPC3220.
This is necessary for initializing LPC32xx UARTs via DT.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

LPC32xx has "Standard" UARTs that are actually 16550A compatible but have
bigger FIFOs. Since the already supported 16X50 line still doesn't match here,
we agreed on adding a new type.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Acked-by: NAlan Cox <alan@linux.intel.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently, serial drivers don't report buffer overruns. When a buffer overrun
occurs, tty_insert_flip_char returns 0, and no attempt is made to insert that
same character again (i.e. it is lost). This patch reports buffer overruns via
the buf_overrun field in the port's icount structure.
Signed-off-by: NCorbin Atkinson <corbin.atkinson@xxxxxx>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

port->baudclk_rate should be compared to the rate of port->baudclk,
because port->baudclk_rate was assigned as the rate of port->baudclk previously.
So to check that the current baudclk rate is same as previous rate,
the target of comparison sholud be the rate of port->baudclk.
Signed-off-by: NJun-Ho, Yoon <junho78.yoon@samsung.com>
Signed-off-by: NKyoungil Kim <ki0351.kim@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit b9562545 ("bcma: complete workaround for BCMA43224 and
BCM4313") introduced the wrong masks for setting the chip control
registers - the "mask" parameter is inverse.

It should be the mask of bits *not* changed, which is admittedly a bit
non-intuitive.

The incorrect mask not only causes the driver to not work correctly on
the chips affected (eg the BCM43224 on the Macbook Air 4,2) but the
state persists over a soft reset, causing the next boot to not
necessarily see the device correctly.
Reported-and-tested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Tested-by: NSeth Forshee <seth.forshee@canonical.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Arend Van Spriel <arend@broadcom.com>
Cc: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Cc: Brett Rudley <brudley@broadcom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This should fix the problem reported by Fengguang:

The coccinelle static checker emits these warnings:

drivers/bcma/scan.c:466:3-9: ERROR: missing iounmap; ioremap on line 451 and execution via conditional on line 465
drivers/bcma/scan.c:540:3-9: ERROR: missing iounmap; ioremap on line 515 and execution via conditional on line 539
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The wrong interrupts where assigned to the cores in
bcma_core_mips_init(). This caused at least my serial console not to
response to any input.

This was caused by this patch which changed the order of the cores in
the list:
commit c334e25c
Author: Rafał Miłecki <zajec5@gmail.com>
Date:   Wed Jul 11 12:37:00 2012 +0200

    bcma: add new cores at the end of list

This should be fixed properly later so that the correct interrupt
numbers are assigned to the cores independently from the ordering of
the list. This patch restores the old behavior again. I will look into
the problem more deeply later.

I also changed the order of the list with the cores and their assigned
interrupt number which gets printed to the log. Now they are printed in
the same order like all the other lists of cores and like it was done
before the patch which changed the order.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

info->control.sta and control.vif may only be dereferenced during the
drv_tx call otherwise could lead to use-after-free bugs.
Signed-off-by: NThomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Wrong pointer variable is being used to parse the rss hash from
receive completions leading to corrupted rss_hash values filled into skb.
Signed-off-by: NSarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RFS filter id can't have the special value RPS_NO_FILTER,
need to skip it when allocating id's.

CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TI LP8788 PMU has the current sink as the keyboard led driver.
The brightness is controlled by the i2c commands.
Configurable parameters can be defined in the platform side.

Patch v2.
(a) use workqueue on changing the brightness

(b) use mutex_lock/unlock when the brightness is set
    and the led block of lp8788 device is enabled

(c) remove err_dev on _probe()
    : just return as returned value if any errors

(d) replace module_init/exit() with module_platform_driver()

(e) add led configuration structure and loading them by default
    if platform data is null
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>

Fixes kernel panic when vblank interrupt triggers before first sync to
vblank request.

(Besides init, remove some relevant leftovers from vblank rework)
Reported-by: NOrtwin Glück <odi@odi.ch>
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Cc: stable@vger.kernel.org [3.5]
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

These will be replaced in the near future, the code isn't yet stable enough
for this merge window however.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

I want this file for the new interfaces...
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Reported-by: NMaarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@canonical.com>

Current name is misleading, because this error can be triggered by other
conditions, like changing STRMOUT parameter without disabling STRMOUT first.
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>