Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

IRQ_LOCOMO_* are never used elsewhere, remove these definitions. As well
as the cascade of these IRQs. IRQ_LOCOMO_*_BASE changed to IRQ_LOCOMO_*.

IRQ_LOCOMO_LT and IRQ_LOCOMO_SPI are likely to be used in a same way as
IRQ_LOCOMO_KEY.

IRQ_LOCOMO_GPIO and the demultiplex handler should really be living
somewhere else.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

It is not necessary and is over-complicated for IRQ_LOCOMO_KEY to
be a cascaded IRQ of IRQ_LOCOMO_KEY_BASE. Removed and introduced
locomokbd_{open,close} for masking/unmasking of the keyboard IRQ.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

These IRQ definitions related to LOCOMO are never referenced anywhere,
thus could be safely removed.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Cc: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Missing AC97 pin configurations are added where pxa_set_ac97_info() are
called for all pxa25x/pxa27x platforms. Where no exact configuration is
provided, use the default as in sound/arm/pxa2xx-ac97-lib.c

Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This is really pxa27x specific and should be kept in pxa27x.c. With this
newly introduced function, the original set_resetgpio_mode() is deprecated.

Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

There are only limited possible LCD pin configurations for pxa25x
platforms, simplify this by macro.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

* Modification of Kconfig to add the Option
* 1 new file : buffalo-wxl-setup.c
This file is inspired from the db-78xx0-setup.c already present.
The following is done:
  - Configure MPP Lines for the plateform (see my patch for MPP)
This is taken from the stock kernel provided by buffalotech (the vendor)
  - GigaBit Ethernet
  - Sata
  - Uart are initiallized in a different way than on the dev board as we
have one core only.
  - USB

The kernel has been running for some days now on my plateform.
Signed-off-by: NSebastien Requiem <sebastien@kolios.dk>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

This patch is composed of two new files :

- mpp.c which is mainly inspired by the same file as in mach-kirkwood

- mpp.h that is written from the documentation provided by Marvell
http://www.marvell.com/products/processors/embedded/discovery_innovation/HW_MV78100_OpenSource.pdf

Moreover, due to some implementation problem, I have
defined some MPPX_UNUSED that offer developers the possibility
to SET MPP to some unused value (such as for Buffalo WXL).

Note: This patch doesn't support MV78200 yet (only 78100 MPP lines have
been written)
Signed-off-by: NSebastien Requiem <sebastien@kolios.dk>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Accept SD CD and SD WP in accordance to
http://plugcomputer.org/data/docs/Sheeva-PowerPlug-V1.3-GTI-090906.pdf
on MPP 47 and 44 respectively on the eSATA SheevaPlug
Signed-off-by: NJohn Holland <john.holland@cellent-fs.de>
Signed-off-by: NNicolas Pitre <nico@marvell.com>
--

Enable the kirkwood SATA SoC interface on the eSATA SheevaPlug.
Signed-off-by: NJohn Holland <john.holland@cellent-fs.de>
Signed-off-by: NNicolas Pitre <nico@marvell.com>
--

Allow basic eSATA SheevaPlug board configuration and build.
Signed-off-by: NJohn Holland <john.holland@cellent-fs.de>
Signed-off-by: NNicolas Pitre <nico@marvell.com>
--

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch fix the below build error for arm1026ej-s processor (IntegratorCP/arm1026ej-s board).
  CC      init/main.o
In file included from include/linux/highmem.h:8,
                 from include/linux/pagemap.h:10,
                 from include/linux/mempolicy.h:62,
                 from init/main.c:52:
arch/arm/include/asm/cacheflush.h:134:2: error: #error Unknown cache maintainence model
make[1]: *** [init/main.o] Erreur 1
make: *** [init] Erreur 2
Signed-off-by: NAbdoulaye Walsimou Gaye <walsimou@walsimou.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

It appears the wrong GPIO registers were used
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@gmail.com>

The 'outer_cache' variable is needed by the outer_inv_range(),
outer_clean_range() and outer_flush_range() functions, which are
declared as inline in asm/cacheflush.h.  Otherwise drivers built
as a loadable module, which access these functions, will have
an undefined symbol.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The platform data allocated with kmalloc() will become unreachable once
the init is complete, so it should be freed. The problem was discovered
by kmemleak.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes the power LED on DNS-323 revision A1, and adds timer
support for (hopefully) both A1 and B1 revisions.

Power LED on revision A1 is active low and also requires GPIO 4 to be
low to work.

Tested on my DNS-323 revision A1.

I have set the default trigger to timer as that replicates the
behaviour of the original firmware, userspace can change the trigger
at the end of the boot process providing a useful indication that
booting has completed.
Signed-off-by: NNicolas Pitre <nico@marvell.com>

This patch add a GPIO LED named "ns_v2:blue:sata" which can be used to
enable or disable SATA activity LED blinking.
Signed-off-by: NSimon Guinot <sguinot@lacie.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

The Internet and Network Space v2 boards are very close. The only
difference is that there is no USB type B plug wired on the Internet
Space v2.
Signed-off-by: NSimon Guinot <sguinot@lacie.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Signed-off-by: NSimon Guinot <sguinot@lacie.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

This patch allow user-space to configure the switch power-off behaviour
via the gpiolib sysfs interface.
Signed-off-by: NSimon Guinot <sguinot@lacie.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Signed-off-by: NNicolas Pitre <nico@marvell.com>

Signed-off-by: NNicolas Pitre <nico@marvell.com>

... and replace misuse of arch_reset() with arm_machine_restart().
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Signed-off-by: NZhu Qingsen <zhuqs@cn.fujitsu.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Inspired by the mach-ep93xx flattening work, there is really not
much difference between the OpenRD base and client board support
so they should be merged together.
Signed-off-by: NAlexander Clouter <alex@digriz.org.uk>
Acked-by: NSimon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

The (void *) cast is not needed when setting dev.platform_data to the
address of the data. Remove the casts.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

The (void *) cast is not needed when setting dev.platform_data to the
address of the data. Remove the casts.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

The (void *) cast is not needed when setting dev.platform_data to the
address of the data. Remove the casts.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Currently the omap serial clocks are autoidled after 5 seconds.
However, this causes lost characters on the serial ports. As this
is considered non-standard behaviour for Linux, disable the timeout.

Note that this will also cause blocking of any deeper omap sleep
states.

To enable the autoidling of the serial ports, do something like
this for each serial port:

# echo 5 > /sys/devices/platform/serial8250.0/sleep_timeout
# echo 5 > /sys/devices/platform/serial8250.1/sleep_timeout
...
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

I have found an access to already released memory in
clk_debugfs_register_one() function.
Signed-off-by: NMarek Skuczynski <mareksk7@gmail.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

David Binderman ran the sourceforge tool cppcheck over the source code of the
new Linux kernel 2.6.33-rc6:

[./arm/mach-omap2/mux.c:492]: (error) Buffer access out-of-bounds

13 characters + 1 digit + 1 zero byte is more than 14 characters.

Also add a comment on mode0 name length in case new omaps
start using longer names.
Reported-by: NDavid Binderman <dcb314@hotmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

3630 has more mux signals than 34xx. The additional pins
exist in omap36xx_cbp_subset, but are not initialized
as the superset is missing these offsets. This causes
the following errors during the boot:

mux: Unknown entry offset 0x236
mux: Unknown entry offset 0x22e
mux: Unknown entry offset 0x1ec
mux: Unknown entry offset 0x1ee
mux: Unknown entry offset 0x1f4
mux: Unknown entry offset 0x1f6
mux: Unknown entry offset 0x1f8
mux: Unknown entry offset 0x1fa
mux: Unknown entry offset 0x1fc
mux: Unknown entry offset 0x22a
mux: Unknown entry offset 0x226
mux: Unknown entry offset 0x230
mux: Unknown entry offset 0x22c
mux: Unknown entry offset 0x228

Fix this by adding the missing offsets to omap3 superset.
Note that additionally the uninitialized pins need to be
skipped on 34xx.

Based on an earlier patch by Allen Pais <allen.pais@ti.com>.
Reported-by: NAllen Pais <allen.pais@ti.com>
Signed-off-by: NAllen Pais <allen.pais@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>