Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

When finding or allocating a loop device, loop_probe() did not take
partition numbers into account so that it can result to a different
device. Consider following example:

$ sudo modprobe loop max_part=15
$ ls -l /dev/loop*
brw-rw---- 1 root disk 7,   0 2011-05-24 22:16 /dev/loop0
brw-rw---- 1 root disk 7,  16 2011-05-24 22:16 /dev/loop1
brw-rw---- 1 root disk 7,  32 2011-05-24 22:16 /dev/loop2
brw-rw---- 1 root disk 7,  48 2011-05-24 22:16 /dev/loop3
brw-rw---- 1 root disk 7,  64 2011-05-24 22:16 /dev/loop4
brw-rw---- 1 root disk 7,  80 2011-05-24 22:16 /dev/loop5
brw-rw---- 1 root disk 7,  96 2011-05-24 22:16 /dev/loop6
brw-rw---- 1 root disk 7, 112 2011-05-24 22:16 /dev/loop7
$ sudo mknod /dev/loop8 b 7 128
$ sudo losetup /dev/loop8 ~/temp/disk-with-3-parts.img
$ sudo losetup -a
/dev/loop128: [0805]:278201 (/home/namhyung/temp/disk-with-3-parts.img)
$ ls -l /dev/loop*
brw-rw---- 1 root disk 7,    0 2011-05-24 22:16 /dev/loop0
brw-rw---- 1 root disk 7,   16 2011-05-24 22:16 /dev/loop1
brw-rw---- 1 root disk 7, 2048 2011-05-24 22:18 /dev/loop128
brw-rw---- 1 root disk 7, 2049 2011-05-24 22:18 /dev/loop128p1
brw-rw---- 1 root disk 7, 2050 2011-05-24 22:18 /dev/loop128p2
brw-rw---- 1 root disk 7, 2051 2011-05-24 22:18 /dev/loop128p3
brw-rw---- 1 root disk 7,   32 2011-05-24 22:16 /dev/loop2
brw-rw---- 1 root disk 7,   48 2011-05-24 22:16 /dev/loop3
brw-rw---- 1 root disk 7,   64 2011-05-24 22:16 /dev/loop4
brw-rw---- 1 root disk 7,   80 2011-05-24 22:16 /dev/loop5
brw-rw---- 1 root disk 7,   96 2011-05-24 22:16 /dev/loop6
brw-rw---- 1 root disk 7,  112 2011-05-24 22:16 /dev/loop7
brw-r--r-- 1 root root 7,  128 2011-05-24 22:17 /dev/loop8

After this patch, /dev/loop8 - instead of /dev/loop128 - was
accessed correctly.

In addition, 'range' passed to blk_register_region() should
include all range of dev_t that LOOP_MAJOR can address. It does
not need to be limited by partition numbers unless 'max_loop'
param was specified.
Signed-off-by: NNamhyung Kim <namhyung@gmail.com>
Cc: Laurent Vivier <Laurent.Vivier@bull.net>
Cc: stable@kernel.org
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

The 'max_part' parameter controls the number of maximum partition
a loop block device can have. However if a user specifies very
large value it would exceed the limitation of device minor number
and can cause a kernel panic (or, at least, produce invalid
device nodes in some cases).

On my desktop system, following command kills the kernel. On qemu,
it triggers similar oops but the kernel was alive:

$ sudo modprobe loop max_part0000
 ------------[ cut here ]------------
 kernel BUG at /media/Linux_Data/project/linux/fs/sysfs/group.c:65!
 invalid opcode: 0000 [#1] SMP
 last sysfs file:
 CPU 0
 Modules linked in: loop(+)

 Pid: 43, comm: insmod Tainted: G        W   2.6.39-qemu+ #155 Bochs Bochs
 RIP: 0010:[<ffffffff8113ce61>]  [<ffffffff8113ce61>] internal_create_group=
+0x2a/0x170
 RSP: 0018:ffff880007b3fde8  EFLAGS: 00000246
 RAX: 00000000ffffffef RBX: ffff880007b3d878 RCX: 00000000000007b4
 RDX: ffffffff8152da50 RSI: 0000000000000000 RDI: ffff880007b3d878
 RBP: ffff880007b3fe38 R08: ffff880007b3fde8 R09: 0000000000000000
 R10: ffff88000783b4a8 R11: ffff880007b3d878 R12: ffffffff8152da50
 R13: ffff880007b3d868 R14: 0000000000000000 R15: ffff880007b3d800
 FS:  0000000002137880(0063) GS:ffff880007c00000(0000) knlGS:00000000000000=
00
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 0000000000422680 CR3: 0000000007b50000 CR4: 00000000000006b0
 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
 DR3: 0000000000000000 DR6: 0000000000000000 DR7: 0000000000000000
 Process insmod (pid: 43, threadinfo ffff880007b3e000, task ffff880007afb9c=
0)
 Stack:
  ffff880007b3fe58 ffffffff811e66dd ffff880007b3fe58 ffffffff811e570b
  0000000000000010 ffff880007b3d800 ffff880007a7b390 ffff880007b3d868
  0000000000400920 ffff880007b3d800 ffff880007b3fe48 ffffffff8113cfc8
 Call Trace:
  [<ffffffff811e66dd>] ? device_add+0x4bc/0x5af
  [<ffffffff811e570b>] ? dev_set_name+0x3c/0x3e
  [<ffffffff8113cfc8>] sysfs_create_group+0xe/0x12
  [<ffffffff810b420e>] blk_trace_init_sysfs+0x14/0x16
  [<ffffffff8116a090>] blk_register_queue+0x47/0xf7
  [<ffffffff8116f527>] add_disk+0xdf/0x290
  [<ffffffffa00060eb>] loop_init+0xeb/0x1b8 [loop]
  [<ffffffffa0006000>] ? 0xffffffffa0005fff
  [<ffffffff8100020a>] do_one_initcall+0x7a/0x12e
  [<ffffffff81096804>] sys_init_module+0x9c/0x1e0
  [<ffffffff813329bb>] system_call_fastpath+0x16/0x1b
 Code: c3 55 48 89 e5 41 57 41 56 41 89 f6 41 55 41 54 49 89 d4 53 48 89 fb=
 48 83 ec 28 48 85 ff 74 0b 85 f6 75 0b 48 83 7f 30 00 75 14 <0f> 0b eb fe =
48 83 7f 30 00 b9 ea ff ff ff 0f 84 18 01 00 00 49
 RIP  [<ffffffff8113ce61>] internal_create_group+0x2a/0x170
  RSP <ffff880007b3fde8>
 ---[ end trace a123eb592043acad ]---
Signed-off-by: NNamhyung Kim <namhyung@gmail.com>
Cc: Laurent Vivier <Laurent.Vivier@bull.net>
Cc: stable@kernel.org
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

In file included from drivers/block/drbd/drbd_main.c:54:                        drivers/block/drbd/drbd_int.h:1190: warning: parameter has incomplete type

Forward declarations of enums do not work.

Fix it unpleasantly by moving the prototype.

Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NLars Ellenberg <drbd-dev@lists.linbit.com>
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>

Found these with the help of ispell -l.
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>

An administrative detach used to request a state change directly to D_DISKLESS,
first suspending IO to avoid the last put_ldev() occuring from an endio handler,
potentially in irq context.

This is not enough on the receiving side (typically secondary), we may miss
some peer_req on the way to local disk, which then may do the last put_ldev()
from their drbd_peer_request_endio().

This patch makes the detach always go through the intermediate D_FAILED state.
We may consider to rename it D_DETACHING.

Alternative approach would be to create yet an other work item to be scheduled
on the worker, do the destructor work from there, and get the timing right.

manually picked commit 564040f from the drbd 8.4 branch.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The old (optimistic) implementation could shrink the bio size
on an primary device.

Shrinking the bio size on a primary device is bad. Since there
we might get BIOs with the old (bigger) size shortly after
we published the new size.

The new implementation is more conservative, and eventually
increases the max_bio_size on a primary device (which is valid).
It does so, when it knows the local limit AND the remote limit.

 We cache the last seen max_bio_size of the peer in the meta
 data, and rely on that, to make the operation of single
 nodes more efficient.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

It seems that the real cause of all the issues where that
we did not noticed in drbd_try_connect() when the other
guy closes one socket if the round trip time gets higher
than 100ms. There were that 100ms hard coded!
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

It is no longer sufficient to trigger on local WRITE,
we need to check on (rq_state & RQ_IN_ACT_LOG)
before calling drbd_al_complete_io also in the error path.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

If there is no replication traffic within the idle timeout
(ping-int seconds), DRBD will send a P_PING,
and adjust the timeout to ping-timeout.

If there is no P_PING_ACK received within this ping-timeout,
DRBD finally drops the connection, and tries to re-establish it.

To decide which timeout was active, we compared the current timeout
with the ping-timeout, and dropped the connection, if that was the case.

By default, ping-int is 10 seconds, ping-timeout is 500 ms.

Unfortunately, if you configure ping-timeout to be the same as ping-int,
expiry of the idle-timeout had been mistaken for a missing ping ack,
and caused an immediate reconnection attempt.

Fix:
Allow both timeouts to be equal, use a local variable
to store which timeout is active.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

We limit ourselves to a configurable maximum number of pages used as
temporary bio pages.

If the configured "max_buffers" is not big enough to match the bandwidth
of the respective deployment, a distributed deadlock could be triggered
by e.g. fast online verify and heavy application IO.

TCP connections would block on congestion, because both receivers
would wait on pages to become available.

Fortunately the respective senders in this case would be able to give
back some pages already. So do that.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

For some time we contemplated calling the "struct lru_cache"
a "struct tracked_set", and some comments kept the ts_ prefix.

Fix those to match the member field names.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

In case a write failes on the local disk, go into D_INCONSISTENT
disk state. That causes future reads of that block to be shipped
to the peer.

Read retry remote was already in place.

Actually the documentation needs to get fixed now. Since the
application is still shielded from the error. (as long as we have
only a single disk failing) The difference to detach is that
we keep the disk. And therefore might keep all the other, still
working sectors up to date.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Merge branches 'for-jens/xen-backend-fixes' and 'for-jens/xen-blkback-v3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen into for-2.6.40/drivers

If the backends, which use these two functions, are compiled as
a module we need these two functions to be exported.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

We only supported the M2P (and P2M) override only for the
GNTMAP_contains_pte type mappings. Meaning that we grants
operations would "contain the machine address of the PTE to update"
If the flag is unset, then the grant operation is
"contains a host virtual address". The latter case means that
the Hypervisor takes care of updating our page table
(specifically the PTE entry) with the guest's MFN. As such we should
not try to do anything with the PTE. Previous to this patch
we would try to clear the PTE which resulted in Xen hypervisor
being upset with us:

(XEN) mm.c:1066:d0 Attempt to implicitly unmap a granted PTE c0100000ccc59067
(XEN) domain_crash called from mm.c:1067
(XEN) Domain 0 (vcpu#0) crashed on cpu#3:
(XEN) ----[ Xen-4.0-110228  x86_64  debug=y  Not tainted ]----

and crashing us.

This patch allows us to inhibit the PTE clearing in the PV guest
if the GNTMAP_contains_pte is not set.

On the m2p_remove_override path we provide the same parameter.

Sadly in the grant-table driver we do not have a mechanism to
tell m2p_remove_override whether to clear the PTE or not. Since
the grant-table driver is used by user-space, we can safely assume
that it operates only on PTE's. Hence the implementation for
it to work on !GNTMAP_contains_pte returns -EOPNOTSUPP. In the future
we can implement the support for this. It will require some extra
accounting structure to keep track of the page[i], and the flag.

[v1: Added documentation details, made it return -EOPNOTSUPP instead
 of trying to do a half-way implementation]
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

The sector number on empty barrier requests may (will?) be -1, which,
given that it's being treated as unsigned 64-bit quantity, will almost
always exceed the actual (virtual) disk's size.

Inspired by Konrad's "When writting barriers set the sector number to
zero...".

While at it also add overflow checking to the math in vbd_translate().
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

vbd_resize() up_read()'s xs_state.suspend_mutex twice in a row via double
xenbus_transaction_end() calls. The next down_read() in
xenbus_transaction_start() (at eg. the next resize attempt) hangs.

Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=618317Acked-by: NJan Beulich <jbeulich@novell.com>
Acked-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NLaszlo Ersek <lersek@redhat.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

The recent changes caused this field of the structure to be offset a bit.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

And not depend on the driver being built with -DDEBUG flag.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

No need for that '_st' and xen_blkif is more apt.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Not point of the blkif.h file. It is not used by the frontend.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

CHECK: multiple assignments should be avoided
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Break up the macro usage.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

with more details.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

From the blkif.h header, which was exposed to the frontend.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

It is not really used for anything.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

To make it easier to read.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

And also make them uniform and prefix the message with 'xen-blkback'.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

If the backend supports the 'feature-flush-cache' mode, use that
instead of the 'feature-barrier' support.

Currently there are three backends that support the 'feature-flush-cache'
mode: NetBSD, Solaris and Linux kernel. The 'flush' option is much
light-weight version than the 'barrier' support so lets try to use as
there are no filesystems in the kernel that use full barriers anymore.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>