This patch prepares the driver for the at91sam9X5 processors,
which don't have the mb0 bug.
(See commit 3a5655a5 for more details.)
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This is the second of two patches converting the at91_can driver from a
compile time mailbox setup to a dynamic one.

This patch first adds a id_table to the platform driver. Depending on the
driver_data the constants for the mailbox setup is selected. Then all
remaining prime mailbox constants are converted to functions, using the
run time selected mailbox constants.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This is the first of two patches converting the at91_can driver from a
compile time mailbox setup to a dynamic one.

This patch converts all derived mailbox constants to functions.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

... and use it for AT91_NEXT_MB_MASK,
AT91_IRQ_MB_RX and AT91_IRQ_MB_RX, too.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

...instead of deriving it from AT91_MB_RX_FIRST and AT91_MB_RX_NUM.
This removes a level of computation, when switching the driver from
compile time constants to runtime values.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>

Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Semicolons are not necessary after switch/while/for/if braces
so remove them.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit b1c43f82.

It was broken in so many ways, and results in random odd pty issues.

It re-introduced the buggy schedule_work() in flush_to_ldisc() that can
cause endless work-loops (see commit a5660b41: "tty: fix endless
work loop when the buffer fills up").

It also used an "unsigned int" return value fo the ->receive_buf()
function, but then made multiple functions return a negative error code,
and didn't actually check for the error in the caller.

And it didn't actually work at all.  BenH bisected down odd tty behavior
to it:
  "It looks like the patch is causing some major malfunctions of the X
   server for me, possibly related to PTYs.  For example, cat'ing a
   large file in a gnome terminal hangs the kernel for -minutes- in a
   loop of what looks like flush_to_ldisc/workqueue code, (some ftrace
   data in the quoted bits further down).

   ...

   Some more data: It -looks- like what happens is that the
   flush_to_ldisc work queue entry constantly re-queues itself (because
   the PTY is full ?) and the workqueue thread will basically loop
   forver calling it without ever scheduling, thus starving the consumer
   process that could have emptied the PTY."

which is pretty much exactly the problem we fixed in a5660b41.

Milton Miller pointed out the 'unsigned int' issue.
Reported-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: NMilton Miller <miltonm@bga.com>
Cc: Stefan Bigler <stefan.bigler@keymile.com>
Cc: Toby Gray <toby.gray@realvnc.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When interface is down, driver prints false warning messages
during lro configuration through ethtool.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function attempts to free one fragment beyond the number of
fragments that were actually mapped.  This patch brings back the limit
to the correct spot.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Tested-by: NAlex Williamson <alex.williamson@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch simplifies the logic and locking in sungem significantly:

 - LLTX is gone, all private locks are gone, mutex is gone
 - We don't poll the PHY while the interface is down
 - The above allowed me to get rid of a pile of state flags
   using the proper interface state provided by the networking
   stack when needed and overall simplify the driver a lot
 - Allocate the bulk of RX skbs at init time using GFP_KERNEL
 - Fix a bug where the dev->features were set after register_netdev()
 - Added GRO while at it
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No need to check for 10, 100, 1000, 10000 explicitly. Just make this
generic and check for invalid values only (similar check is in ethtool
userspace app). This enables correct speed handling for slave devices
with "nonstandard" speeds.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Reviewed-by: NNicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The failed_get label is used after the call to clk_get has succeeded, so it
should be moved up above the call to clk_put.

The failed_req labels doesn't do anything different than failed_get, so
delete it.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r exists@
expression e1,e2;
statement S;
@@

e1 = clk_get@p1(...);
... when != e1 = e2
    when != clk_put(e1)
    when any
if (...) { ... when != clk_put(e1)
               when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
 } else S
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the DM9000 driver requests the primary interrupt before it
resets the chip and puts it into a known good state. This means that if
the chip is asserting interrupt for some reason we can end up with a
screaming IRQ that the interrupt handler is unable to deal with. Avoid
this by only requesting the interrupt after we've reset the chip so we
know what state it's in.

This started manifesting itself on one of my boards in the past month or
so, I suspect as a result of some core infrastructure changes removing
some form of mitigation against bad behaviour here, even when things boot
it seems that the new code brings the interface up more quickly.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Go to existing error handling code at the end of the function that calls
clk_put.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r exists@
expression e1,e2;
statement S;
@@

e1 = clk_get@p1(...);
... when != e1 = e2
    when != clk_put(e1)
    when any
if (...) { ... when != clk_put(e1)
               when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
 } else S
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces the CAIF HSI Protocol Driver for the
CAIF Link Layer.

This driver implements a platform driver to accommodate for a
platform specific HSI devices. A general platform driver is not
possible as there are no HSI side Kernel API defined.
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This avoids messages like this after suspend:

   cdc_ncm 2-1.4:1.6: no reset_resume for driver cdc_ncm?
   cdc_ncm 2-1.4:1.7: no reset_resume for driver cdc_ncm?
   cdc_ncm 2-1.4:1.6: usb0: unregister 'cdc_ncm' usb-0000:00:1d.0-1.4, CDC NCM

This is important for the Ericsson F5521gw GSM/UMTS modem.
Otherwise modemmanager looses the fact that the cdc_ncm and cdc_acm devices
belong together.

The cdc_ether module does the same.
Signed-off-by: NStefan Metzmacher <metze@samba.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of setting CL45 mode for every CL45 access, apply it once during initialization.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modify XGXS functions to follow rest of PHY scheme.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix link status synchronization between the primary function, and rest functions.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move BCM8726 module detection code into a separate function to be called only once during initialization.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch relocates some functions as a preparation for next patches, and also fixes some grammar mistakes.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix BCM84833 register settings.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On 57712 chip, port number is enumerated per engine, so it requires adjustment in port display to the user.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case TX fault is detected on Fiber PHYs, declare the link as down until TX fault is gone.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change return status from u8 to int.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Display the current media type connected to the port in ethtool.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for new phy BCM8722.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In some cases we can read wrong temperature value. If after that
temperature value will not be updated to good one, we badly configure
tx power parameters and device is unable to send a data.

Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=35932

Cc: stable@kernel.org # 2.6.39+
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is the same fix as

   commit 84105160
   Author: Matteo Croce <technoboy85@gmail.com>
   Date:   Fri Dec 3 02:25:08 2010 +0100

   The ath9k driver subtracts 3 dBm to the txpower as with two radios the
   signal power is doubled.
   The resulting value is assigned in an u16 which overflows and makes
   the card work at full power.

in two more places. I grepped the ath tree and didn't find any others.

Cc: stable@kernel.org
Signed-off-by: NDaniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of failing the init/probe code in the driver fallback to the older opcode to ensure
the driver is loaded thereby enabling users to upgrade the f/w to whatever version is required.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit e5cb966c.

It causes new build regressions with gcc-4.2 which is
pretty common on non-x86 platforms.
Reported-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

catc_ctrl_run() calls usb_submit_urb() with GFP_KERNEL, while it is called from
catc_ctrl_async() and catc_ctrl_done() with catc->ctrl_lock spinlock held.

The patch replaces GFP_KERNEL with GFP_ATOMIC.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a driver crash during packet reception due to not enough
bytes allocated in the skb. Since the loop reads out 4 bytes at a time, we
need to allow for up to 3 bytes of slack space.
Signed-off-by: NDennis Aberilla <denzzzhome@yahoo.com>
Signed-off-by: NDavid S. Miller <davem@zippy.davemloft.net>

For 6150 devices, modify the supported PCI subsystem ID.

Cc: stable@kernel.org
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

zd1211 devices register 'EP 4 OUT' endpoint as Interrupt type on USB 2.0:

      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x04  EP 4 OUT
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               1

However on USB 1.1 endpoint becomes Bulk:

      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x04  EP 4 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0

Commit 37939810 assumed that endpoint is
always interrupt type and changed usb_bulk_msg() calls to usb_interrupt_msg().

Problem here is that usb_bulk_msg() on interrupt endpoint selfcorrects the
call and changes requested pipe to interrupt type (see usb_bulk_msg).
However with usb_interrupt_msg() on bulk endpoint does not correct the
pipe type to bulk, but instead URB is submitted with interrupt type pipe.

So pre-2.6.39 used usb_bulk_msg() and therefore worked with both endpoint
types, however in 2.6.39 usb_interrupt_msg() with bulk endpoint causes
ohci_hcd to fail submitted URB instantly with -ENOSPC and preventing zd1211rw
from working with OHCI.

Fix this by detecting endpoint type and using correct endpoint/pipe types
for URB. Also fix asynchronous zd_usb_iowrite16v_async() to use right
URB type on 'EP 4 OUT'.

Cc: stable@kernel.org
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix kernel oops when trying to use passive scheduled scans.  The
reason was that in passive scans there are no SSIDs, so there was a
NULL pointer dereference.

To solve the problem, we now check the number of SSIDs provided in the
sched_scan request and only access the list if there's one or more
(ie. passive scan is not forced).  We also force all the channels to
be passive by adding the IEEE80211_CHAN_PASSIVE_SCAN flag locally
before the checks in the wl1271_scan_get_sched_scan_channels()
function.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>