Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Reported-by: NIan Kent <raven@themaw.net>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Add at91 sama5d4 xplained board support.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This commit adds the Device Tree files for the Armada 39x family of
processors, as well as one Armada 398 Development Board.

Like for other Marvell EBU families, a common armada-39x.dtsi contains
the description of the common features of all Armada 39x SoCs, while
armada-390.dtsi and armada-398.dtsi respectively describe the
specificities of those SoCs.

Finally, an armada-398-db.dts file is added to describe the Armada 398
Development Board itself.

So far, the following features are supported:

 * SMP: dual Cortex-A9
 * Basic ARM IPs: SCU, timer, GIC, L2 cache
 * Basic Marvell IPs: pin-muxing, clocks, system controller, MBus
   controller, MPIC interrupt controller, timer, CPU reset for SMP,
   PMSU.
 * I2C
 * SPI
 * SDHCI
 * XOR
 * NAND
 * UART
 * PCIe

Additional features will be supported in the future.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

DT file to enable the Wireless Audio reference design based on the
BCM58305.
Reviewed-by: NRay Jui <rjui@broadcom.com>
Reviewed-by: NScott Branden <sbranden@broadcom.com>
Tested-by: NScott Branden <sbranden@broadcom.com>
Signed-off-by: NJonathan Richardson <jonathar@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Add a DTS file for MINIX NEO-X8, a Meson8-based digital media player.
Signed-off-by: NBeniamino Galvani <b.galvani@gmail.com>
Signed-off-by: NCarlo Caione <carlo@endlessm.com>

The Linksys WRT1900AC (Mamba) is a router that has

- 2 mini-PCIe slots with Marvell 88W8864 radios
- 1 USB 3.0 port
- 1 USB 2.0/eSATAp port
- 2 Ethernet interfaces connected to a 88E6172 switch (1x WAN + 4x LAN)
- 128MB NAND flash
- 256MB RAM

gregory.clement@free-electrons.com: - add ARM to the title
	- fix the reference to CONFIG_DEBUG_MVEBU_UART0_ALTERNATE
	- fix the unbalanced comment for the syscfg partition
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

cx92755.dtsi describes CX92755 on chip peripherals. cx92755_equinox.dts
describes the Equinox evaluation board for the CX92755 SoC.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The entries are separated as ARM V4/V5 and ARM V7 as some other per-SoC config
options may be removed in the near future.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This add support for Rayeager PX2, Rockchip PX2 based development board
made by ChipSPARK.
Signed-off-by: NFUKAUMI Naoki <naobsd@gmail.com>
Tested-by: NAndy Yan <andy.yan@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

This adds support for Firefly-RK3288, Rockchip RK3288 based development
boards made by Firefly.

There are 2 dts for 2 versions of the board. rk3288-firefly-beta.dts is
for the beta version, rk3288-firefly.dts is for the mass production version.
Signed-off-by: NFUKAUMI Naoki <naobsd@gmail.com>

[removed gmac reference, due to the gmac node going through the net-tree]
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Signed-off-by: NOlof Johansson <olof@lixom.net>

The Hyundai A7HD is a 7" 16:9 A10 powered tablet featuring 1G RAM, 8G
nand, 1024x600 IPS screen, a mini hdmi port, mini usb receptacle and a
headphones port for details see: http://linux-sunxi.org/Hyundai_A7HD

Cc: Mark Janssen <maniac@maniac.nl>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The pogoplug differs from the SheevaPlug only by a
few details, but especially in the led assignments.
This patch was tested under Gentoo Linux and is
based on dts files from Arch Linux ARM and OpenWrt.
Suggested-by: NFelix Kaechele <heffer@fedoraproject.org>
Suggested-by: NOleg Rakhmanov <moonman.ca@gmail.com>
Signed-off-by: NChristoph Junghans <ottxor@gentoo.org>
[Andrew Lunn <andrew@lunn.ch>: Fixed subject line]
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

Add dts file for Hisilicon hip01 ca9x2 board
Signed-off-by: NWang Long <long.wanglong@huawei.com>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>
[olof: Folded in smp enable-method from a different patch]
Signed-off-by: NOlof Johansson <olof@lixom.net>

This patch add support for Marsboard A10 board.

The Marsboard A10 is a A10 based development board with 1G RAM, 1G NAND,
micro SD card slot, SATA 2.0 socket, 10/100 ethernet, mini HDMI port,
1 USB OTG port and 2 USB 2.0 ports. Board does not use the AXP209 pmic,
it does not have a pmic at all.
Board also have 2 expansion 70 pin headers.
Signed-off-by: NAleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The mk802_a10s re-uses is the "classic" mk802 case and functionality, but has
an A10s SoC inside rather then the A10, it features 512M or 1G RAM, 4G nand,
a mini-hdmi female connector, USB-A receptacle, mini-usb receptacle (OTG)
and a sdio realtek wifi chip. Unlike the original mk802 it does have a pmic,
the axp152.

For more details see: http://linux-sunxi.org/Semitime_g2Signed-off-by: NHans de Goede <hdegoede@redhat.com>
[Maxime: Changed the compatible and node names labels]
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The mk802ii is a revised version of the mk802 A10 based hdmi tv-stick, it
features 1G RAM, 4G nand, a hdmi male connector, USB-A receptacle, 2 micro
usb receptacles (OTG & power) and USB-wifi, and does come with an axp209 pmic.

For more details see: http://linux-sunxi.org/Rikomagic_mk802iiSigned-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The mk802 is the "classic" Allwinner A10 based hdmi tv-stick, it features
512M or 1G RAM, 4G nand, a mini-hdmi female connector, USB-A receptacle,
mini-usb receptacle (OTG) and USB-wifi. Somewhat unique the mk802 does not
use the AXP209 pmic, it does not have a pmic at all.

For more details see: http://linux-sunxi.org/Rikomagic_mk802Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Chuwi V7 is an A10 (sun4i) based tablet with 1G of RAM, 16G of nand flash,
microsd slot, 7" 1024x768 lvds ips panel, mini hdmi out, headphones out,
stereo speakers, front & back camera and usb wifi.

It is clearly marked "CHUWI", "V7" and "Model: CW0825" on the back of the
tablet.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add support for the new Bananapro A20 development board from lemaker.org.
This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for
OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver,
3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Ippo Q8H v1.2 is almost identical to the v5, still it needs a separate
dtb file since some gpio-s surrounding the wlan/bluetooth are different,
it uses different camera sensors, and different DRAM timings.

Note that atm neither the wlan/bluetooth nor the camera are supported, so
atm their is no difference between the dts files, but because of the different
DRAM timings there are already separate u-boot configs for the 2 different
versions, and the 1.2 config refers to sun8i-a23-ippo-q8h-v1.2.dtb to be
future proof, so we need to provide a sun8i-a23-ippo-q8h-v1.2.dtb file.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The CSQ CS908 is an A31s based top-set box, with 1G RAM, 8G NAND,
rtl8188etv usb wifi, 2 USB A receptacles (1 connected through the OTG
controller), ethernet, 3.5 mm jack with a/v out and hdmi out.

Note it has no sdcard slot and therefore can only be fel booted.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>

Luxul XWC-1000 is a controller device based on BCM4708 SoC. The only
unusual thing in its DTS file is "ubi" partition on NAND flash.
Signed-off-by: NDan Haab <dhaab@luxul.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>

The file is roughly sorted alphabetically (with some exceptions where
old options have been split in two), so alphascale should go at the
top instead of at the bottom.

Also linewrap like other entries have been lately.
Signed-off-by: NOlof Johansson <olof@lixom.net>

for now it is wary basic SoC description with most important IPs needed
to make this device work
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This allows booting the device with basic functionality.

Note that at least on my revision c board the DDR3 does
not seem to work properly and only some of the memory
can be reliably used.

Also, the mainline u-boot does not seem to properly
initialize the ethernet, so I've been using the old TI
u-boot at:

http://arago-project.org/git/projects/?p=u-boot-omap3.git;a=summary

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

B2199 HDK is the reference board for STiH418 SoC.
It has the following characteristics:
 - 3GB DDR3
 - 8GB eMMC / SD-Card slot
 - 32MB NOR Flash
 - 1 x Gbit Ethernet
 - 1 x USB3.0 port
 - 2 x USB2.0 ports
 - 1 x Sata or Mini-PCIe port
 - 1 x WiFi 802.11ac (Quantenna)
 - 1 x HDMI out
 - 1 x HDMI in
 - 1 x SPDIF
Reviewed-by: NPeter Griffin <peter.griffin@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

CSR atlas7 uses Network on Chip(NoC) bus architecture, there are dozens
of MARCOs, in each MARCO, there are dozens of hardware modules.
Signed-off-by: NZhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: NHao Liu <Hao.Liu@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>

A number of arches (EXYNOS/IMX/TEGRA) are separated out into finer grained
definitions whether it be sub ARCH or SOC definitions. The device tree blobs
should only be built if the specific option is enabled that supports that
device or it might be that there's an expectation that the device is supported
when in actual fact it's not. This ensures only the relevant bits are built.

Also standardised the line break between the arch/soc definitions and the
dtbs to be on separate lines for better consistency as per feedback.
Signed-off-by: NPeter Robinson <pbrobinson@gmail.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NShawn Guo <shawn.guo@freescale.com>
[olof: Fixed stray \ in one of the IMX rules]
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add DTS for the Hardkernel Odroid XU3. The name of the DTS file is
kept the same as the vendors naming, which means it's prefixed with
exynos5422 instead of exynos5800 as the SoC name even though it
includes the exyno5800 dtsi.
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Tested-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

MARCO will not be supported any more. it has been replaced by CSR
atlas7.
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>

The A388-GP is a board produced by Marvell that holds

- 1 PCIe slot
- 2 mini PCIe slot (one of them is multiplexed with the PCIe slot,
  muxing is selected through the GPIO expander)
- 1 16MB SPI-NOR
- 2 Gigabit Ethernet ports
- 4 SATA ports (2 of them are multiplexed with the mini PCIe slots,
  muxing is selected through the GPIO expander)
- 1 SDIO slot
- 1 USB3 port
- 2 USB2 port
- 2 GPIO/interrupts expander on I2C
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

This SoC belongs to the Armada 38x family. The main difference with
the Armada 385 is that the 388 can handle two more SATA
ports. Currently the consequence is the use of a different compatible
string for the pinctrl node, in order to be able to use the pins
associated to this 2 new SATA ports. The second SATA controller has
also been moved from the armada38x.dtsi as it it specific to the
Armada388 version.

In the same time the Armada385 DB and Armada 385 RD board have been
renamed in the 388 one and now include the armada-388.dtsi file. AS
both of them have 4 SATA ports the SoC used on them were wrongly
described.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

The A385-AP is a board produced by Marvell that holds 3 mPCIe slot, a 16MB
SPI-NOR, 3 Gigabit Ethernet ports, USB3 and NAND flash storage.

[gregory.clement@free-electrons.com: switch the license to the dual
X11/GPL with the agreement of the author]
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

The AM437x Industrial Development Kit (IDK) is
an application development platform targeted at
industrial communication and control applications.

It comes with a 3-phase motor driver, PROFINET,
PROFIBUS and a few other industrial communication
interfaces.

The board has 1GiB of DDR3 RAM, QSPI NOR flash,
a 100% discrete power design (no PMIC) and an
on-board 2MP camera (not supported with Linux
as of this writing).
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

For more information about the Udoo boards:
http://www.udoo.org/Signed-off-by: NRobert Nelson <robertcnelson@gmail.com>
Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch adds support for Seagate BlackArmor NAS220.

The Seagate BlackArmor NAS 220 is a NAS system based on Marvell 88f6192. It has
32MB NAND and 128MB DRAM. It has two SATA slots, one Gigabit Ethernet port, two
USB 2.0 ports, two buttons and three LEDs. There is a serial port available on
the CN5 connector on the board (1 - TX, 4 - RX, 6 - GND).

The only functionality still not implemented is the bi-color led on the front
panel (status). Pins mpp22 and mpp23 control this led. Setting mpp22 to high and
mpp23 to low results in orange color. Setting mpp22 to low and mpp23 to high
results in blue color.

The third led is wired to show the SATA activity on the two drives.
Signed-off-by: NEvgeni Dobrev <evgeni@studio-punkt.com>
Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

Add basic i.MX6SoloX Sabre Auto board support, currently
only debug UART and uSDHC are supported on this board.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Makes sure the dtb is built for multiplatform builds.
Signed-off-by: NUlrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>