This fixes a typo in the MMC_RX_CRC_ERROR constant.
Signed-off-by: NNik Nyby <nikolas@gnu.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current implementation of descriptor init procedure only takes
care about setting/clearing ownership flag in "des0"/"des1"
fields while it is perfectly possible to get unexpected bits
set because of the following factors:

 [1] On driver probe underlying memory allocated with
     dma_alloc_coherent() might not be zeroed and so
     it will be filled with garbage.

 [2] During driver operation some bits could be set by SD/MMC
     controller (for example error flags etc).

And unexpected and/or randomly set flags in "des0"/"des1"
fields may lead to unpredictable behavior of GMAC DMA block.

This change addresses both items above with:

 [1] Use of dma_zalloc_coherent() instead of simple
     dma_alloc_coherent() to make sure allocated memory is
     zeroed. That shouldn't affect performance because
     this allocation only happens once on driver probe.

 [2] Do explicit zeroing of both "des0" and "des1" fields
     of all buffer descriptors during initialization of
     DMA transfer.

And while at it fixed identation of dma_free_coherent()
counterpart as well.
Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: arc-linux-dev@synopsys.com
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add constants and callback functions for the dwmac on rk3368 socs.
As can be seen, the base structure is the same, only registers and
the bits in them moved slightly.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mac settings like RGMII/RMII, speeds etc are done in the so called
"General Register Files", contain numerous other settings as well and
always seem to change between Rockchip SoCs. Therefore abstract the
register accesses into a per-soc ops struct to make this reusable on
other Rockchip SoCs.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The first iteration of the dwmac-rk support did access an intermediate
clock directly below the pll selector. This was removed in a subsequent
revision, but the clock and one invocation remained. This results in
the driver trying to set the rate of a non-existent clock when the soc
and not some external source provides the phy clock for RMII phys.

So set the rate of the correct clock and remove the remaining now
completely unused definition.

Fixes: 436f5ae08f9d ("GMAC: add driver for Rockchip RK3288 SoCs integrated GMAC")
Cc: stable@vger.kernel.org
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a first version the driver did want to do some gpio wiggling, which
of course never made it into the kernel, but somehow these register
defines where forgotten. Remove them, as they shouldn't be here.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These kind of informations are only useful for debugging and should not be
displayed in normal modules message.
Signed-off-by: NRomain Perier <romain.perier@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethernet controller available in IPQ806x is a Synopsys DesignWare
Gigabit MAC IP core, already supported by the stmmac driver.

This glue layer implements some platform specific settings required to
get the controller working on an IPQ806x based platform.
Signed-off-by: NMathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case DT is used, this change adds the ability to the stmmac driver to
detect a fixed-link PHY, instanciate it, and use it during
phy_connect().

Fixed link PHYs DT usage is described in:
Documentation/devicetree/bindings/net/fixed-link.txt
Signed-off-by: NMathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On stmmac driver, PHY specification in device-tree was done using the
non-standard property "snps,phy-addr". Specifying a PHY on a different
MDIO bus that the one within the stmmac controller doesn't seem to be
possible when device-tree is used.

This change adds support for the phy-handle property, as specified in
Documentation/devicetree/bindings/net/ethernet.txt.
Signed-off-by: NMathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

stmmac DebugFS entries are currently global to the driver. As a result,
having more than one stmmac device in the system creates the following
error:
* ERROR stmmaceth, debugfs create directory failed
* stmmac_hw_setup: failed debugFS registration

This also results in being able to access the debugfs information for
the first registered device only.

This patch changes the debugfs structure to have one sub-directory per
net-device. Files under "/sys/kernel/debug/stmmaceth" will now show-up
under /sys/kernel/debug/stmmaceth/ethN/.
Signed-off-by: NMathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the caller already check the presence of a of_node there
is no need to repeat the check in stmmac_probe_config_dt.

There is also no point in checking the return value of the
of_match_device function since if there wasn't match in the
first place we would never be in this function.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since stmmac_dvr_probe takes care of setting driver data and
assign resources to the priv structure there is no need to
access the priv structure from the other probe functions.
This mean that this function can be changed into just return
an int and thus simplifying the callers.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Creat a struct that contain all the resources that needs to be
assigned to the priv struct in stmmac_dvr_probe. This makes it
possible to factor out more common code from the other probe
functions and also use this struct to hold the resources as
they are fetched.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move setting of driver data into stmmac_dvr_probe so the
other probe functions don't have to. This will help to
simplify the other probe functions later.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This also matches with the sibling call netdev_alloc_skb_ip_align() made in
rx fast path.
Signed-off-by: NVineet Gupta <vgupta@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-generic replaces the driver inside the stmmac
platform code. This turns stmmac platform into a library
used by drivers for common platform driver functions.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert platform glue layer into a proper platform
driver and add it to the build system.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert platform glue layer into a proper platform
driver and add it to the build system.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert platform glue layer into a proper platform
driver and add it to the build system.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert platform glue layer into a proper platform
driver and add it to the build system.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert platform glue layer into a proper platform
driver and add it to the build system.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert platform glue layer into a proper platform
driver and add it to the build system.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create a new driver around the generic device tree match strings
in the stmmac platform code. This driver is intended to be used
by all platforms that doesn't require any platform specific code
to function or is using platform data.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prepare the stmmac platform code to support standalone drivers
by exporting the need functions and having of_match_device use
the match table reference already present in the driver struct.

This will allow us to reuse the platform driver functions from
this code easily in other stand alone platform drivers.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for Ethernet on NXP LPC18xx and LPC43xx using the
dwmac driver. This glue is required to setup phy interface
mode, MII or RMII, on the SoC.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This file is built off of a tristate Kconfig option and also contains
modular function calls so it should explicitly include module.h to
avoid compile breakage during header shuffles done in the future.

Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Configure flow control correctly, and based on the receive fifo size read
as a property from the devicetree since the Synopsys stmmac fifo sizes are
configurable based on a particular chip's implementation. This patch maintains
the previous incorrect behavior unless the receive fifo size is found in the
devicetree.
Signed-off-by: NVince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unicast pause frame detect was not being enabled for the Synopsys stmmac. This
patch sets Unicast pause frame detect in MAC register 6 so that pause frame
detection by the stmmac conforms to IEEE 802.3, Annex 31B.3.3 Receive
Operation - Specifically, a MAC shall respond to pause frames containing
either the reserved multicast address or the unique physical address
associated with this station.
Signed-off-by: NVince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Read the tx-fifo-depth and rx-fifo-depth from the devicetree. The Synopsys
stmmac controller fifos are configurable per product instance, and the fifo
sizes are needed to configure certain features correctly such as flow control.
Signed-off-by: NVince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add defines and documentation for enabling flow control on the stmmac. Flow
control was not implemented correctly on the stmmac driver and is currently
non-functional as a result. This is the first in a series of small patches
to correctly implement this feature.
Signed-off-by: NVince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An oops exists in the flow of stmmac_release().
phy_ethtool_get_wol() depends on phydev->drv.
phydev->drv will be null after stmmac_mdio_unreg() completes.

Steps to reproduce on Quark X1000:

1. ifconfig eth0 192.168.0.1
2. rmmod stmmac_pci

To fix this stmmac_mdio_unreg() should be run after unregister_netdev().
Signed-off-by: NBryan O'Donoghue <pure.logic@nexus-software.ie>
Reported-by: NDan O'Donovan <dan.odonovan@emutex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In socfpga_dwmac_parse_data forward error code from devm_reset_control_get.
This gives the driver another chance to laod if altr,rst-mgr is loaded after
the network driver.
Signed-off-by: NPhil Reid <preid@electromag.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DWMAC block on certain SoCs (such as IMG Pistachio) have a second
clock which must be enabled in order to access the peripheral's
register interface, so add support for requesting and enabling an
optional "pclk".
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the driver to use ns_to_timespec64() instead of
open coding the same logic.

Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This device stores the number of seconds in a 32 bit register.  So
more work is needed on this driver before the year 2038 comes around.

Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.

$ git ls-files drivers/net/ethernet/ | \
  while read file ; do \
    codespell -w $file; \
  done

I removed a false positive in e1000_hw.h
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not having a reset control line to the ethernet controller should not be a
hard failure. Instead, add support for deferred probing and just print out
a debug statement.
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we're getting IRQs after lots of resources are already
allocated:
 * netdev
 * clocks
 * MDIO bus
Also HW gets initialized by the time when checking IRQs as well.

Now there's a possibility for master interrupt controller to be not
probed yet. This will lead to exit from GMAC probe routine with "-
EPROBE_DEFER" and so deferred probe will hapen later on.

But since we exited the first GMAC probe without release of all
allocated resources there could be conflicts on subsequent probes.

For example this is what happens for me:
 --->8---
 stmmaceth e0018000.ethernet: no reset control found
 stmmac - user ID: 0x10, Synopsys ID: 0x37
  Ring mode enabled
  DMA HW capability register supported
  Normal descriptors
  RX Checksum Offload Engine supported (type 2)
  TX Checksum insertion supported
  Enable RX Mitigation via HW Watchdog Timer
 libphy: stmmac: probed
 eth0: PHY ID 20005c7a at 1 IRQ POLL (stmmac-0:01) active
 platform e0018000.ethernet: Driver stmmaceth requests probe deferral
 ...
 ...
 ...
 stmmaceth e0018000.ethernet: no reset control found
 stmmac - user ID: 0x10, Synopsys ID: 0x37
  Ring mode enabled
  DMA HW capability register supported
  Normal descriptors
  RX Checksum Offload Engine supported (type 2)
  TX Checksum insertion supported
  Enable RX Mitigation via HW Watchdog Timer
 ------------[ cut here ]------------
 WARNING: CPU: 0 PID: 6 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x4e/0x68()
 sysfs: cannot create duplicate filename
'/devices/platform/axs10x_mb/e0018000.ethernet/mdio_bus/stmmac-0'
 CPU: 0 PID: 6 Comm: kworker/u2:0 Not tainted 4.0.0-rc1-next-20150303+#8
 Workqueue: deferwq deferred_probe_work_func

 Stack Trace:
  arc_unwind_core+0xb8/0x114
  warn_slowpath_common+0x5a/0x8c
  warn_slowpath_fmt+0x2e/0x38
  sysfs_warn_dup+0x4e/0x68
  sysfs_create_dir_ns+0x98/0xa0
  kobject_add_internal+0x8c/0x2e8
  kobject_add+0x4a/0x8c
  device_add+0xc6/0x448
  mdiobus_register+0x6c/0x164
  stmmac_mdio_register+0x112/0x264
  stmmac_dvr_probe+0x6c0/0x85c
  stmmac_pltfr_probe+0x2e4/0x50c
  platform_drv_probe+0x26/0x5c
  really_probe+0x76/0x1dc
  bus_for_each_drv+0x42/0x7c
  device_attach+0x64/0x6c
  bus_probe_device+0x74/0xa4
  deferred_probe_work_func+0x50/0x84
  process_one_work+0xf8/0x2cc
  worker_thread+0x110/0x478
  kthread+0x8a/0x9c
  ret_from_fork+0x14/0x18
 ---[ end trace a2dfaa7d630c8be1 ]---
 ------------[ cut here ]------------
 WARNING: CPU: 0 PID: 6 at lib/kobject.c:240
kobject_add_internal+0x218/0x2e8()
 kobject_add_internal failed for stmmac-0 with -EEXIST, don't try to
register things with the same name in the same di.
 CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G        W
4.0.0-rc1-next-20150303+ #8
 Workqueue: deferwq deferred_probe_work_func

 Stack Trace:
  arc_unwind_core+0xb8/0x114
  warn_slowpath_common+0x5a/0x8c
  warn_slowpath_fmt+0x2e/0x38
  kobject_add_internal+0x218/0x2e8
  kobject_add+0x4a/0x8c
  device_add+0xc6/0x448
  mdiobus_register+0x6c/0x164
  stmmac_mdio_register+0x112/0x264
  stmmac_dvr_probe+0x6c0/0x85c
  stmmac_pltfr_probe+0x2e4/0x50c
  platform_drv_probe+0x26/0x5c
  really_probe+0x76/0x1dc
  bus_for_each_drv+0x42/0x7c
  device_attach+0x64/0x6c
  bus_probe_device+0x74/0xa4
  deferred_probe_work_func+0x50/0x84
  process_one_work+0xf8/0x2cc
  worker_thread+0x110/0x478
  kthread+0x8a/0x9c
  ret_from_fork+0x14/0x18
 ---[ end trace a2dfaa7d630c8be2 ]---
 libphy: mii_bus stmmac-0 failed to register
 : Cannot register as MDIO bus
 stmmac_pltfr_probe: main driver probe failed
 stmmaceth: probe of e0018000.ethernet failed with error -22
 --->8---

Essential fix is to check for IRQs availability as early as possible and
then safely go to deferred probe if IRQs are not there yet.
Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.

This is done using Coccinelle and semantic patch used for
this is as follows:

// <smpl>
@@
expression x,y,z,a,b;
@@

-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: NVaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>