We store c45 PHY's id information in c45_ids, so it should be used to
check the matching between PHY driver and PHY device for c45 PHY.
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sierra Wireless MC7305/MC7355 with USB ID 1199:9041 also provide a
second QMI/network interface like the MC73xx with USB ID 1199:68c0 on
USB interface #10 when used in the appropriate USB configuration.
Add the corresponding QMI_FIXED_INTF entry to the qmi_wwan driver.

Please note that the second QMI/network interface is not working for
early MC73xx firmware versions like 01.08.x as the device does not
respond to QMI messages on the second /dev/cdc-wdm port.
Signed-off-by: NReinhard Speyerer <rspmn@arcor.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The TCCR.TSRQn bit may get clearead after TCCR gets read, so that TCCR write
would get skipped. We don't need to check this bit before setting.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The keystone qmss will raise interrupt when packet arrive at the
receive queue. Only control available to avoid interrupt from happening
is to keep the free descriptor queue (FDQ) empty in the receive side.
So the filling of descriptors into the FDQ has to happen after
request_irq() call is made as part of knav_queue_enable_notify(). So
move the function netcp_rxpool_refill() after this call.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "follow" fail_over_mac policy is useful for multiport devices that
either become confused or incur a performance penalty when multiple
ports are programmed with the same MAC address, but the same MAC
address still may happened by this steps for this policy:

1) echo +eth0 > /sys/class/net/bond0/bonding/slaves
   bond0 has the same mac address with eth0, it is MAC1.

2) echo +eth1 > /sys/class/net/bond0/bonding/slaves
   eth1 is backup, eth1 has MAC2.

3) ifconfig eth0 down
   eth1 became active slave, bond will swap MAC for eth0 and eth1,
   so eth1 has MAC1, and eth0 has MAC2.

4) ifconfig eth1 down
   there is no active slave, and eth1 still has MAC1, eth2 has MAC2.

5) ifconfig eth0 up
   the eth0 became active slave again, the bond set eth0 to MAC1.

Something wrong here, then if you set eth1 up, the eth0 and eth1 will have the same
MAC address, it will break this policy for ACTIVE_BACKUP mode.

This patch will fix this problem by finding the old active slave and
swap them MAC address before change active slave.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Tested-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

7445E0 contains an ECO which disconnected the internal SF2 pseudo-PHY which was
known to conflict with the external pseudo-PHY of BCM53125 switches. This
motivated the need to utilize the internal SF2 MDIO controller via indirect
register reads/writes to control external Broadcom switches due to this address
conflict (both responded at address 30d).

For 7445E0, the internal pseudo-PHY of the SF2 switch got disconnected, and as
a consequence this prevents the internal SF2 MDIO bus controller from reading
data (reads back everything as 0) since the MDI line is tied low.

Fix this by making the indirect register reads and writes conditional to
7445D0, on 7445E0 we can utilize the SWITCH_MDIO controller (backed by
mdio-unimac and not the DSA created slave MII bus).

We utilize of_machine_is_compatible() here since this is the only way for use
to differentiate between these two chips in a way that does not violate layers
or becomes (too) vendor-specific.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the bond is enslaving a device with different type it will be setup
by it, but if after being setup the enslave fails the bond doesn't
switch back its type and also keeps pointers to foreign structures that can
be long gone. Thus revert back any type changes if the enslave failed and
the bond had to change its type.
Example:
 Before patch:
$ echo lo > bond0/bonding/slaves
-bash: echo: write error: Cannot assign requested address
$ ip l sh bond0
20: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default
    link/loopback 16:54:78:34:bd:41 brd 00:00:00:00:00:00
$ echo +eth1 > bond0/bonding/slaves
$ ip l sh bond0
20: bond0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT group default qlen 1000
    link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff
(notice the MASTER flag is gone)

 After patch:
$ echo lo > bond0/bonding/slaves
-bash: echo: write error: Cannot assign requested address
$ ip l sh bond0
21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
    link/ether 6e:66:94:f6:07:fc brd ff:ff:ff:ff:ff:ff
$ echo +eth1 > bond0/bonding/slaves
$ ip l sh bond0
21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
    link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: e36b9d16 ("bonding: clean muticast addresses when device changes type")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the bonding is being unloaded and the netdevice notifier is
unregistered it executes NETDEV_UNREGISTER for each device which should
remove the bond's proc entry but if the device enslaved is not of
ARPHRD_ETHER type and is in front of the bonding, it may execute
bond_release_and_destroy() first which would release the last slave and
destroy the bond device leaving the proc entry and thus we will get the
following error (with dynamic debug on for bond_netdev_event to see the
events order):
[  908.963051] eql: event: 9
[  908.963052] eql: IFF_SLAVE
[  908.963054] eql: event: 2
[  908.963056] eql: IFF_SLAVE
[  908.963058] eql: event: 6
[  908.963059] eql: IFF_SLAVE
[  908.963110] bond0: Releasing active interface eql
[  908.976168] bond0: Destroying bond bond0
[  908.976266] bond0 (unregistering): Released all slaves
[  908.984097] ------------[ cut here ]------------
[  908.984107] WARNING: CPU: 0 PID: 1787 at fs/proc/generic.c:575
remove_proc_entry+0x112/0x160()
[  908.984110] remove_proc_entry: removing non-empty directory
'net/bonding', leaking at least 'bond0'
[  908.984111] Modules linked in: bonding(-) eql(O) 9p nfsd auth_rpcgss
oid_registry nfs_acl nfs lockd grace fscache sunrpc crct10dif_pclmul
crc32_pclmul crc32c_intel ghash_clmulni_intel ppdev qxl drm_kms_helper
snd_hda_codec_generic aesni_intel ttm aes_x86_64 glue_helper pcspkr lrw
gf128mul ablk_helper cryptd snd_hda_intel virtio_console snd_hda_codec
psmouse serio_raw snd_hwdep snd_hda_core 9pnet_virtio 9pnet evdev joydev
drm virtio_balloon snd_pcm snd_timer snd soundcore i2c_piix4 i2c_core
pvpanic acpi_cpufreq parport_pc parport processor thermal_sys button
autofs4 ext4 crc16 mbcache jbd2 hid_generic usbhid hid sg sr_mod cdrom
ata_generic virtio_blk virtio_net floppy ata_piix e1000 libata ehci_pci
virtio_pci scsi_mod uhci_hcd ehci_hcd virtio_ring virtio usbcore
usb_common [last unloaded: bonding]

[  908.984168] CPU: 0 PID: 1787 Comm: rmmod Tainted: G        W  O
4.2.0-rc2+ #8
[  908.984170] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[  908.984172]  0000000000000000 ffffffff81732d41 ffffffff81525b34
ffff8800358dfda8
[  908.984175]  ffffffff8106c521 ffff88003595af78 ffff88003595af40
ffff88003e3a4280
[  908.984178]  ffffffffa058d040 0000000000000000 ffffffff8106c59a
ffffffff8172ebd0
[  908.984181] Call Trace:
[  908.984188]  [<ffffffff81525b34>] ? dump_stack+0x40/0x50
[  908.984193]  [<ffffffff8106c521>] ? warn_slowpath_common+0x81/0xb0
[  908.984196]  [<ffffffff8106c59a>] ? warn_slowpath_fmt+0x4a/0x50
[  908.984199]  [<ffffffff81218352>] ? remove_proc_entry+0x112/0x160
[  908.984205]  [<ffffffffa05850e6>] ? bond_destroy_proc_dir+0x26/0x30
[bonding]
[  908.984208]  [<ffffffffa057540e>] ? bond_net_exit+0x8e/0xa0 [bonding]
[  908.984217]  [<ffffffff8142f407>] ? ops_exit_list.isra.4+0x37/0x70
[  908.984225]  [<ffffffff8142f52d>] ?
unregister_pernet_operations+0x8d/0xd0
[  908.984228]  [<ffffffff8142f58d>] ?
unregister_pernet_subsys+0x1d/0x30
[  908.984232]  [<ffffffffa0585269>] ? bonding_exit+0x23/0xdba [bonding]
[  908.984236]  [<ffffffff810e28ba>] ? SyS_delete_module+0x18a/0x250
[  908.984241]  [<ffffffff81086f99>] ? task_work_run+0x89/0xc0
[  908.984244]  [<ffffffff8152b732>] ?
entry_SYSCALL_64_fastpath+0x16/0x75
[  908.984247] ---[ end trace 7c006ed4abbef24b ]---

Thus remove the proc entry manually if bond_release_and_destroy() is
used. Because of the checks in bond_remove_proc_entry() it's not a
problem for a bond device to change namespaces (the bug fixed by the
Fixes commit) but since commit
f9399814 ("bonding: Don't allow bond devices to change network
namespaces.") that can't happen anyway.
Reported-by: NCarol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: a64d49c3 ("bonding: Manage /proc/net/bonding/ entries from
                      the netdev events")
Tested-by: NCarol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6xxx_priv_state structure contains an fid_mask, where 1 means
the FID is free to use, 0 means the FID is in use.

This patch fixes the bit clear in mv88e6xxx_leave_bridge() when
assigning a new FID to a port.

Example scenario: I have 7 ports, port 5 is CPU, port 6 is unused (no
PHY). After setting the ports 0, 1 and 2 in bridge br0, and ports 3 and
4 in bridge br1, I have the following fid_mask: 0b111110010110 (0xf96).

Indeed, br0 uses FID 0, and br1 uses FID 3.

After setting nomaster for port 0, I get the wrong fid_mask: 0b10 (0x2).

With this patch we correctly get 0b111110010100 (0xf94), meaning port 0
uses FID 1, br0 uses FID 0, and br1 uses FID 3.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ANY_LAYOUT is a compatibility feature. It's implied
for VERSION_1 devices, and non-transitional devices
might not offer it. Change code to behave accordingly.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

First, dma_sync_single_for_cpu() shouldn't have been called in the first place
(it's a streaming DMA API), dma_unmap_single() should have been called instead.
Second, dma_unmap_single() call after handing the buffer to napi_gro_receive()
makes little sense.  Moreover desc->dptr might not be valid at this point.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The regulators power and transceiver are optional. If those are not
present, the pointer (or error pointer) is correctly handled by the
driver, hence we can use devm_regulator_get_optional safely, which
avoids regulators getting created.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

If a valid power regulator or a dummy regulator is used (which
happens to be the case when no regulator is specified), restart_work
is queued no matter whether the device was running or not at suspend
time. Since work queues get initialized in the ndo_open callback,
resuming leads to a NULL pointer exception.

Reverse exactly the steps executed at suspend time:
- Enable the power regulator in any case
- Enable the transceiver regulator if the device was running, even in
  case we have a power regulator
- Queue restart_work only in case the device was running

Fixes: bf66f373 ("can: mcp251x: Move to threaded interrupts instead of workqueues.")
Signed-off-by: NStefan Agner <stefan@agner.ch>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Inet6addr notifier is atomic and runs in bh context without RTNL when
ipv6 receives router advertisement packet and performs autoconfiguration.

Proper fix still in discussion. Let's at least plug the bug.
v1: http://lkml.kernel.org/r/20150514135618.14062.1969.stgit@buzz
v2: http://lkml.kernel.org/r/20150703125840.24121.91556.stgit@buzzSigned-off-by: NKonstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In tx path rcu_read_lock_bh() is held, so we need rcu_deference_bh().
This fixes the following warning:

 ===============================
 [ INFO: suspicious RCU usage. ]
 4.1.0-rc1+ #1007 Not tainted
 -------------------------------
 drivers/net/ipvlan/ipvlan.h:106 suspicious rcu_dereference_check() usage!

 other info that might help us debug this:

 rcu_scheduler_active = 1, debug_locks = 0
 1 lock held by dhclient/1076:
  #0:  (rcu_read_lock_bh){......}, at: [<ffffffff817e8d84>] rcu_lock_acquire+0x0/0x26

 stack backtrace:
 CPU: 2 PID: 1076 Comm: dhclient Not tainted 4.1.0-rc1+ #1007
 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
  0000000000000001 ffff8800d381bac8 ffffffff81a4154f 000000003c1a3c19
  ffff8800d4d0a690 ffff8800d381baf8 ffffffff810b849f ffff880117d41148
  ffff880117d40000 ffff880117d40068 0000000000000156 ffff8800d381bb18
 Call Trace:
  [<ffffffff81a4154f>] dump_stack+0x4c/0x65
  [<ffffffff810b849f>] lockdep_rcu_suspicious+0x107/0x110
  [<ffffffff8165a522>] ipvlan_port_get_rcu+0x47/0x4e
  [<ffffffff8165ad14>] ipvlan_queue_xmit+0x35/0x450
  [<ffffffff817ea45d>] ? rcu_read_unlock+0x3e/0x5f
  [<ffffffff810a20bf>] ? local_clock+0x19/0x22
  [<ffffffff810b4781>] ? __lock_is_held+0x39/0x52
  [<ffffffff8165b64c>] ipvlan_start_xmit+0x1b/0x44
  [<ffffffff817edf7f>] dev_hard_start_xmit+0x2ae/0x467
  [<ffffffff817ee642>] __dev_queue_xmit+0x50a/0x60c
  [<ffffffff817ee7a7>] dev_queue_xmit_sk+0x13/0x15
  [<ffffffff81997596>] dev_queue_xmit+0x10/0x12
  [<ffffffff8199b41c>] packet_sendmsg+0xb6b/0xbdf
  [<ffffffff810b5ea7>] ? mark_lock+0x2e/0x226
  [<ffffffff810a1fcc>] ? sched_clock_cpu+0x9e/0xb7
  [<ffffffff817d56f9>] sock_sendmsg_nosec+0x12/0x1d
  [<ffffffff817d7257>] sock_sendmsg+0x29/0x2e
  [<ffffffff817d72cc>] sock_write_iter+0x70/0x91
  [<ffffffff81199563>] __vfs_write+0x7e/0xa7
  [<ffffffff811996bc>] vfs_write+0x92/0xe8
  [<ffffffff811997d7>] SyS_write+0x47/0x7e
  [<ffffffff81a4d517>] system_call_fastpath+0x12/0x6f

Fixes: 2ad7bf36 ("ipvlan: Initial check-in of the IPVLAN driver.")
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Acked-by: NMahesh Bandewar <maheshb@google.com>
Acked-by: NKonstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All structures used in traffic forwarding are rcu-protected:
ipvl_addr, ipvl_dev and ipvl_port. Thus we can unhash addresses
without synchronization. We'll anyway hash it back into the same
bucket: in worst case lockless lookup will scan hash once again.
Signed-off-by: NKonstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add missing kfree_rcu(addr, rcu);
Signed-off-by: NKonstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

They are unused after commit f631c44b ("ipvlan: Always set broadcast bit in
multicast filter").
Signed-off-by: NKonstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 6c3e921b.

commit 6c3e921b ("net: fec: Ensure clocks are enabled while using mdio
 bus") prevents the kernel to boot on mx6 boards, so let's revert it.
Reported-by: NTyler Baker <tyler.baker@linaro.org>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.

Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.

Cc: Bernd Krumboeck <b.krumboeck@gmail.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.

Cc: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.

Cc: Thomas Körper <thomas.koerper@esd.eu>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.

Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.

Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.

Cc: Anant Gole <anantgole@ti.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.

Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.

Cc: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.

Cc: Aaron Wu <Aaron.wu@analog.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The > should be >=.  I also added spaces around the '-' operations so
the code is a little more consistent and matches the condition better.

Fixes: f53c3fe8 ('xen-netback: Introduce TX grant mapping')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 514ac99c "can: fix multiple delivery of a single CAN frame for
overlapping CAN filters" requires the skb->tstamp to be set to check for
identical CAN skbs.

Without timestamping to be required by user space applications this timestamp
was not generated which lead to commit 36c01245 "can: fix loss of CAN frames
in raw_rcv" - which forces the timestamp to be set in all CAN related skbuffs
by introducing several __net_timestamp() calls.

This forces e.g. out of tree drivers which are not using alloc_can{,fd}_skb()
to add __net_timestamp() after skbuff creation to prevent the frame loss fixed
in mainline Linux.

This patch removes the timestamp dependency and uses an atomic counter to
create an unique identifier together with the skbuff pointer.

Btw: the new skbcnt element introduced in struct can_skb_priv has to be
initialized with zero in out-of-tree drivers which are not using
alloc_can{,fd}_skb() too.
Signed-off-by: NOliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The previous change 3973c526 (net: can: c_can: Disable pins when CAN
interface is down) causes a slight glitch on the pinctrl settings when used.
Since commit ab78029e (drivers/pinctrl: grab default handles from device core),
the device core will automatically set the default pins. This causes the pins
to be momentarily set to the default and then to the sleep state in
register_c_can_dev(). By adding an optional "enable" state, boards can set the
default pin state to be disabled and avoid the glitch when the switch from
default to sleep first occurs. If the "enable" state is not available
c_can_pinctrl_select_state() falls back to using the "default" pinctrl state.

[Roger Q] - Forward port to v4.2 and use pinctrl_get_select().
Signed-off-by: NJ.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

All the error messages in the driver but  the ones from devm_clk_get() failures
use similar format.  Make those  two messages consitent with others.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Also print the error code when the request_irq() call fails in rcar_can_open(),
rewording  the error message...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Fix typo in the first error message printed by rcar_can_open().

Based on the original patch by Vladimir Barinov.

Fixes: 862e2b6a ("can: rcar_can: support all input clocks")
Reported-by: NVladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Printing IRQ # using "%x" and "%u" unsigned formats isn't quite correct as
'ndev->irq' is of  type *int*, so  the "%d" format  needs to be used instead.

While fixing this, beautify the dev_info() message in rcar_can_probe() a bit.

Fixes: fd115931 ("can: add Renesas R-Car CAN driver")
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

rcar_can_probe() regards 0 as a wrong IRQ #, despite platform_get_irq() that it
calls returns negative error code in that case. This leads to the following
being printed to the console when attempting to open the device:

error requesting interrupt fffffffa

because  rcar_can_open() calls request_irq() with a negative IRQ #, and that
function naturally fails with -EINVAL.

Check for the negative error codes instead and propagate them upstream instead
of just returning -ENODEV.

Fixes: fd115931 ("can: add Renesas R-Car CAN driver")
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

bcmgenet driver needs to separate packet drops from packet errors.

When the driver has to drop a *good* packet, due to lack of buffers or
replacement skbs, increment only dev->stats.[rx|tx]_dropped.

When the driver encounters a bad Rx packet or Tx error, increment only
dev->stats.[rx|tx]_errors + relevant detailed error counter.
Signed-off-by: NPetri Gynther <pgynther@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>